Section 1: IDENTIFICATION - cdn.simplegreen.com
Section 2: HAZARDS IDENTIFICATION . This product is not regulated under the Hazardous Products Regulation (WHMIS 2015). This product has been classified and labelled in accordance with Health Canada as disinfectant drugs under the . Food and Drugs Act . and . Regulations. A safety data
Download Section 1: IDENTIFICATION - cdn.simplegreen.com
Information
Domain:
Source:
Link to this page:
Documents from same domain
Section 2: HAZARDS IDENTIFICATION
cdn.simplegreen.comrequirements of the Occupational Safety and Health Administration applicable to this SDS differ from the labeling requirements of the CPSC, and this SDS may contain additional health hazard information not pertinent to consumer use and not found on the product label.
Simple Green SDS
cdn.simplegreen.comCalculated via OSHA HCS 2012 / Globally Harmonized System of Classification and Labelling of Chemicals . Skin Corrosion/Irritation: Non-irritant per Dermal Irritection® assay modeling. No animal testing performed. Eye Damage/Irritation: Non-irritant per Ocular Irritection® assay modeling. No animal testing performed.
Safety Data Sheet: Simple Green® Industrial Cleaner ...
cdn.simplegreen.comCap or plug leaking containers. Cover all drains. Dike or soak up with inert adsorbent material. Dispose of in appropriate waste containers. See Section 13 for disposal considerations. Section 7: HANDLING AND STORAGE . Precautions for safe handling: Before use carefully read the product label. Use of safe work practices are recommended to avoid eye
Related documents
SECTION 1: IDENTIFICATION - CDMS Home
www.cdms.netFor substances listed in section 3 that are not listed here, there are no established exposure limits from the manufacturer, supplier, importer, or the appropriate advisory agency including: ACGIH (TLV), NIOSH (REL), or OSHA (PEL).
Section 1. Identification - eatoncompressor.com
www.eatoncompressor.com1-Propene, 2-methyl-, homopolymer ≥1 - ≤3 9003-27-4 Any concentration shown as a range is to protect confidentiality or is due to batch variation. There are no additional ingredients present which, within the current knowledge of the supplier and in the concentrations applicable, are
SECTION 1 IDENTIFICATION - K-FLEX USA
www.kflexusa.comPage . 3. of . 9. K-FLEX: May cause moderate skin irritation. Product may be absorbed through the skin, producing effects similar to inhalation or ingestion.
Section 1: IDENTIFICATION - Plains Midstream Canada
www.plainsmidstream.comCondensate - COED to Enbridge SAFETY DATA SHEET Date of Preparation: April 11, 2016 Page 2 of 16 Deerfoot Consulting Inc. Precautionary Statements Prevention: Obtain special instructions before use. Do not handle until all safety precautions have been read and understood.
Section 1: IDENTIFICATION - Plains Midstream Canada
www.plainsmidstream.comSteelman NGL SAFETY DATA SHEET Date of Preparation: April 11, 2016 Deerfoot Consulting Inc. Page 2 of 12 Response: If exposed or concerned: Get medical advice/attention. Get medical advice/attention if …
Section 1: Identification - planborganics.com
www.planborganics.comSafety Data Sheet Section 11: Toxicological Information Primary Routes of Exposure: Inha lation, skin contact, and eye contact Symptoms of Exposure: May act …
Section 1: IDENTIFICATION
www.usor.comVacuum Gas Oil SAFETY DATA SHEET / MATERIAL SAFETY DATA SHEET Date of Preparation: December 2, 2016 Page 1 of 11 Deerfoot Consulting Inc. Section 1: IDENTIFICATION Product Identifier: Vacuum Gas Oil Other Means of Identification : FCC Feedstock; Light Vacuum Gas Oil; Heavy Vacuum Gas Oil; Raw Vacuum Gas Oil.
SECTION 1 - IDENTIFICATION - documents.trex.com
documents.trex.comsection 8 – exposure controls / personal protection : VENTILATION: Provide local exhaust ventilation and general room ventilation to maintain exposure concentrations of thermal decomposition products below the respective OSHA PEL’s.
SECTION 1: IDENTIFICATION - Leica Biosystems
drp8p5tqcb2p5.cloudfront.netPage: 1 of 10 SECTION 1: IDENTIFICATION Product identifier used on the label CV MOUNT Product number 14046430011 Recommended use of the chemical and restrictions on use Recommended use For use when mounting coverglass on top of a prepared specimen. Restrictions on use All other uses.
SECTION 1: Identification - Duro-Last
duro-last.comSECTION 5: Fire Fighting Measures The product is a solid article that will burn if exposed to an ignition source of sufficient heat and intensity, or open flame, such as a welder’s torch.