SECTION 1 - IDENTIFICATION - documents.trex.com
section 8 – exposure controls / personal protection : VENTILATION: Provide local exhaust ventilation and general room ventilation to maintain exposure concentrations of thermal decomposition products below the respective OSHA PEL’s.
Download SECTION 1 - IDENTIFICATION - documents.trex.com
Information
Domain:
Source:
Link to this page:
Documents from same domain
2019 INSTALLATION GUIDE - documents.trex.com
documents.trex.com5 Trerx.comet1x-.8m1e SAFETY When working on any construction project, you should wear protective clothing and safety equipment. Wear safety glasses, gloves, a dust mask and long sleeves,
COMPOSITE DECKING – TREX SELECT
documents.trex.comA. Wood-Plastic Composite Lumber; a. Material Description: Composite Decking consisting of recycled Linear Low Density Polyethylene (LLDPE) and recycled wood. The product is extruded into shapes and sizes as follows: i. Trex Select Decking Boards; 0.875” x …
TREX TRANSCEND RAILING
documents.trex.comself-tapping screws provided (use three outer holes; do not use hole in RSB that is closest to post). If two hole bracket is included, attach with two self-tapping screws (provided). Placing Baluster Spacers 9. Snap baluster spacer into bottom …
2020 DECKING INSTALLATION GUIDE - Trex
documents.trex.comIssues with Concrete, Cement, Mortar, or Stucco Dust When working with cement, concrete, mortar, or stucco, protect the decking as much as possible in order to not get dust particles on the decking surface. These particles, once they get hot or wet, can cause a reaction on the decking surface and are very difficult to remove.
COMPOSITE DECKING – TREX TRANSCEND AND TREX …
documents.trex.comModulus of Elasticity ASTM D4761 412,000psi 200,000 psi Modulus of Rupture ASTM D4761 3280 psi 500 psi * Ultimate strength values are not meant for design analysis. Design value are for tems peratures up to 130F (54C) 2.2 Accessories . A. Fasteners: a. Trex Universal Hideaway Hidden Fasteners
TREX DECKING
documents.trex.combalcony or even a roof-top retreat, trex has you covered. rich textured finish hidden fasteners help keep the rich texture of trex completely pristine and unblemished by deck screws. learn more on page 11. quick cleaning forget sanding and staining. with just soap and water, you can keep your trex deck totally clean. boundless design possibilities
TREX Fascia Installation Recommendations
documents.trex.comTrex Fascia utilized around the perimeter of a deck must be gapped with the same requirements as Trex decking to allow for air flow and expansion/contraction of the fascia. When Using Approved Fascia Fasteners: NOTE: The fasteners listed below can only be used with 1x8 or 1x12 fascia product, and cannot be used with
RAILING GUIDE - Trex
documents.trex.comAluminum Gates Warranties Tools Trex Signature Railing Trex Transcend Railing Trex Select Railing ... Transcend Crown top and Universal top/bottom in VL infill: Round aluminum balusters in BZ posts: ... Add a cocktail rail using Transcend or Select deck boards. For installation, see Cocktail Rail Bracket on page 52. ...
Related documents
SECTION 1: IDENTIFICATION - CDMS Home
www.cdms.netFor substances listed in section 3 that are not listed here, there are no established exposure limits from the manufacturer, supplier, importer, or the appropriate advisory agency including: ACGIH (TLV), NIOSH (REL), or OSHA (PEL).
Section 1. Identification - eatoncompressor.com
www.eatoncompressor.com1-Propene, 2-methyl-, homopolymer ≥1 - ≤3 9003-27-4 Any concentration shown as a range is to protect confidentiality or is due to batch variation. There are no additional ingredients present which, within the current knowledge of the supplier and in the concentrations applicable, are
SECTION 1 IDENTIFICATION - K-FLEX USA
www.kflexusa.comPage . 3. of . 9. K-FLEX: May cause moderate skin irritation. Product may be absorbed through the skin, producing effects similar to inhalation or ingestion.
Section 1: IDENTIFICATION - Plains Midstream Canada
www.plainsmidstream.comCondensate - COED to Enbridge SAFETY DATA SHEET Date of Preparation: April 11, 2016 Page 2 of 16 Deerfoot Consulting Inc. Precautionary Statements Prevention: Obtain special instructions before use. Do not handle until all safety precautions have been read and understood.
Section 1: IDENTIFICATION - Plains Midstream Canada
www.plainsmidstream.comSteelman NGL SAFETY DATA SHEET Date of Preparation: April 11, 2016 Deerfoot Consulting Inc. Page 2 of 12 Response: If exposed or concerned: Get medical advice/attention. Get medical advice/attention if …
Section 1: Identification - planborganics.com
www.planborganics.comSafety Data Sheet Section 11: Toxicological Information Primary Routes of Exposure: Inha lation, skin contact, and eye contact Symptoms of Exposure: May act …
Section 1: IDENTIFICATION
www.usor.comVacuum Gas Oil SAFETY DATA SHEET / MATERIAL SAFETY DATA SHEET Date of Preparation: December 2, 2016 Page 1 of 11 Deerfoot Consulting Inc. Section 1: IDENTIFICATION Product Identifier: Vacuum Gas Oil Other Means of Identification : FCC Feedstock; Light Vacuum Gas Oil; Heavy Vacuum Gas Oil; Raw Vacuum Gas Oil.
Section 1: IDENTIFICATION - cdn.simplegreen.com
cdn.simplegreen.comSection 2: HAZARDS IDENTIFICATION . This product is not regulated under the Hazardous Products Regulation (WHMIS 2015). This product has been classified and labelled in accordance with Health Canada as disinfectant drugs under the . Food and Drugs Act . and . Regulations. A safety data
SECTION 1: IDENTIFICATION - Leica Biosystems
drp8p5tqcb2p5.cloudfront.netPage: 1 of 10 SECTION 1: IDENTIFICATION Product identifier used on the label CV MOUNT Product number 14046430011 Recommended use of the chemical and restrictions on use Recommended use For use when mounting coverglass on top of a prepared specimen. Restrictions on use All other uses.
SECTION 1: Identification - Duro-Last
duro-last.comSECTION 5: Fire Fighting Measures The product is a solid article that will burn if exposed to an ignition source of sufficient heat and intensity, or open flame, such as a welder’s torch.