Spectifications - pipefittingweb.com
Spectifications ANSI (American National Standard Institute) / ASME (American Society of Mechanical Engineers) ANSI / ASME …
Download Spectifications - pipefittingweb.com
Information
Domain:
Source:
Link to this page:
Documents from same domain
Pressure Unit Conversion Table - pipefittingweb.com
www.pipefittingweb.comPressure Unit Conversion Table atm ata ( kg/cm2 ) Torr ( mm Hg) in Hg (32℉) mm water (4℃) in (60℉) bar Mpa Kpa PSI ( lb/in) atm 1 1.033 760 29.92 10332.56 406.79 1.013 0.1013 101.32 14.69 ata ( kg/cm2 ) 0.968 1 735.56 28.96 10000.03 393.71 0.981 0.0981 98.07 14.22
Materials - pipefittingweb.com
www.pipefittingweb.comMaterials Chemical Composition % Mechanical Properties C Mn P S Si Ni Cr Mo N Tensile Strength Yield Strength Elongation HRB Stainless Steel
Concentric and Eccentric Reducers
www.pipefittingweb.comConcentric and Eccentric Reducers MSS SP-75 ANSI B16.9 (in mm) * Wellgrow’s standard. Outside Diameter at Bevel Outside Diameter at Bevel
DIN Flanges - pipefittingweb.com
www.pipefittingweb.comDIN Flanges Summary Chart Rated Pressure (in bar) (1 bar = 14.5 psi = 100 kPa)
Forged High Pressure Pipe Fittings
www.pipefittingweb.comForged High Pressure Pipe Fittings Tel: 886-4-23112576 Fax: 886-4-23112578 E-mail: wellgrow@ms18.hinet.net
90° Long Radius Elbow - pipefittingweb.com
www.pipefittingweb.comLong and Short Radius 45°/ 90° Elbows ANSI B16.9 B16.28 (in mm) * Wellgrow’s standard. Center to End Long Radius Elbows Short Radius Elbows
EN 1092-1 Flanges - pipefittingweb.com
www.pipefittingweb.comFlange type (typ) as in EN 1092-1 01 (Plate [slip-on] flanges for welding) 13 (Hubbed threaded flanges) 02 (Loose plate flanges with weld-on plate collar) 21 (Integral flanges)
Caps - pipefittingweb.com
www.pipefittingweb.comCaps MSS SP-75 ANSI B16.9 (in mm) Nominal Pipe Size (NPS) Outside Diameter at Bevel D Length (2) E Limiting Wall Thickness for Length E Length (3)
Long and Short Radius 45°/ 90° Elbows - …
www.pipefittingweb.comLong and Short Radius 45°/ 90° Elbows ANSI B16.9 B16.28 (in mm) * Wellgrow’s standard. Center to End Long Radius Elbows Short Radius Elbows
Concentric and Eccentric Reducers - pipefittingweb.com
www.pipefittingweb.comConcentric and Eccentric Reducers MSS SP-75 ANSI B16.9 (in mm) * Wellgrow’s standard. Outside Diameter at Bevel Outside Diameter at Bevel
Related documents
Folder API Series 526 NEW 7/13/04 4:37 PM Page 1 …
www.cvisolutions.comType 526 T ype 526 Plain lever H3 T e 526 Open bonnet Type 526 Balanced bellows design Folder API Series 526 NEW 7/13/04 4:37 PM Page 2
Data Sheets & Bulletin: Kunkle Models 6252/6254 …
www.emerson.comKUNKLE MODELS 6252/6254 SAFETY VALVES SAFETY AND RELIEF PRODUCTS FEATURES • Heavy duty high quality cast iron construction with stainless steel semi-nozzle, trim and disc.
PRACTICAL PIPING COURSE - Engineer
www.engineer.caPiping is an assembly of piping components used to convey, distribute, mix, separate, discharge, meter, control or snub fluid flows. Piping also includes pipe-supporting
FORGED STEEL FLANGES - GARTH INDUSTRIAL
www.garthindustrial.com• 4 • FLANGE TYPES, FACINGS AND FINISHES ANSI FLANGES Most forged steel flanges correspond to the requirements of the American Standards Association (ASME/ANSI Standard B16.5)
Orifice Flanges Product Range Catalogue - …
www.hos.co.ukFLANGE / 25 ANSI ORIFICE FLANGES ORIFICE FLANGES are widely used in conjunction with orifice meters for measuring the rate of flow of liquids and gases.
Orifice Plates - Prisma Instruments
www.prisma-instruments.comOrifice plates are most commonly used primary elements for flow measurement in pipelines based on the principle of measurement of ‘differential pressure’ created
The engineer or designer must choose among P - …
www.wmhuittco.comI Weldlng neck FIQURE 6. Weld-neck flanges are hlghly versatile is used to accommodate the slip-on flange or plate flange as a back-up …