Spectifications - pipefittingweb.com
Spectifications ANSI (American National Standard Institute) / ASME (American Society of Mechanical Engineers) ANSI / ASME B1.20.1 Pipe Threads, General Purpose (Inch)
Download Spectifications - pipefittingweb.com
Information
Domain:
Source:
Link to this page:
Documents from same domain
Pressure Unit Conversion Table - pipefittingweb.com
www.pipefittingweb.comPressure Unit Conversion Table atm ata ( kg/cm2 ) Torr ( mm Hg) in Hg (32℉) mm water (4℃) in (60℉) bar Mpa Kpa PSI ( lb/in) atm 1 1.033 760 29.92 10332.56 406.79 1.013 0.1013 101.32 14.69 ata ( kg/cm2 ) 0.968 1 735.56 28.96 10000.03 393.71 0.981 0.0981 98.07 14.22
Materials - pipefittingweb.com
www.pipefittingweb.comMaterials Chemical Composition % Mechanical Properties C Mn P S Si Ni Cr Mo N Tensile Strength Yield Strength Elongation HRB Stainless Steel
Concentric and Eccentric Reducers
www.pipefittingweb.comConcentric and Eccentric Reducers MSS SP-75 ANSI B16.9 (in mm) * Wellgrow’s standard. Outside Diameter at Bevel Outside Diameter at Bevel
DIN Flanges - pipefittingweb.com
www.pipefittingweb.comDIN Flanges Summary Chart Rated Pressure (in bar) (1 bar = 14.5 psi = 100 kPa)
Forged High Pressure Pipe Fittings
www.pipefittingweb.comForged High Pressure Pipe Fittings Tel: 886-4-23112576 Fax: 886-4-23112578 E-mail: wellgrow@ms18.hinet.net
90° Long Radius Elbow - pipefittingweb.com
www.pipefittingweb.comLong and Short Radius 45°/ 90° Elbows ANSI B16.9 B16.28 (in mm) * Wellgrow’s standard. Center to End Long Radius Elbows Short Radius Elbows
EN 1092-1 Flanges - pipefittingweb.com
www.pipefittingweb.comFlange type (typ) as in EN 1092-1 01 (Plate [slip-on] flanges for welding) 13 (Hubbed threaded flanges) 02 (Loose plate flanges with weld-on plate collar) 21 (Integral flanges)
Caps - pipefittingweb.com
www.pipefittingweb.comCaps MSS SP-75 ANSI B16.9 (in mm) Nominal Pipe Size (NPS) Outside Diameter at Bevel D Length (2) E Limiting Wall Thickness for Length E Length (3)
Long and Short Radius 45°/ 90° Elbows - …
www.pipefittingweb.comLong and Short Radius 45°/ 90° Elbows ANSI B16.9 B16.28 (in mm) * Wellgrow’s standard. Center to End Long Radius Elbows Short Radius Elbows
Concentric and Eccentric Reducers - pipefittingweb.com
www.pipefittingweb.comConcentric and Eccentric Reducers MSS SP-75 ANSI B16.9 (in mm) * Wellgrow’s standard. Outside Diameter at Bevel Outside Diameter at Bevel
Related documents
Product Bulletin 1077 Handwheel Actuator September 2017 ...
www.emerson.comwww.Fisher.com Fisher™ 1077 Manual Handwheel Rotary Actuator Fisher 1077 manual‐only handwheel actuator is for use with rotary‐shaft valves such as the 9500 butterfly
FORGED STEEL FLANGES - GARTH INDUSTRIAL
www.garthindustrial.com• 6 • INCHES MILLIMETRES 1 Socket Welding Flanges, sizes NPS 3 1/2 (DN 90) and larger are not covered by ASME/ANSI B16.5. 2 Includes .06" (1.6 mm) raised face. 3 These dimensions correspond to inside diameters of pipe as given in ANSI/ASME B36.10M for Standard Wall Pipe.Thickness of Standard Wall is the same as Schedule 40 in size NPS 10 (DN 250) and smaller.
SEAMLESS WELDING FITTINGS - GARTH INDUSTRIAL
www.garthindustrial.com• 5 • INCHES MILLIMETRES 1Out-of-round is the sum of absolute values of plus and minus tolerance. NPS DN Outside1 Diameter at Bevel O.D. Inside Diameter at End i.D. Wall Thickness Center to End A,B,C,M 90˚ & 45˚ Elbows Tees Crosses Laterals
API Standard 661 - Hudson Products
www.hudsonproducts.comHudson Products Corp. Page 3 of 6 API Standard 661 - 5th Edition / ISO 13706 7.1.7.8 Paragraph 6.1.7.8 of 4th Edition now reads: fiThreads of plugs having nominal diameters 30 mm (1 1/inch) and smaller shall be fine series threads.fl Paragraph 6.1.7.9 was eliminated. 7.1.8.9 Added fiAnnex A.8 may be consulted for further guidance on gasketsfl This annex is new.
SPECIFICATIONS FOR STEEL PIPE
www.kellypipe.com1 return to index Published pipe standards serve three functions. 1. They dictate manufacturing and testing requirements and prescribed methods of measuring the required mechani-
Internal Threading Technology - LMT FETTE TOOLS
www.lmtfettetools.comContents www.lmtusa.com 1 USA Bottoming Style Taps Rasant – V Inch – Full Bottoming 4 Rasant – V Metric – Full Bottoming 5 Rasant – IQ Plus Inch – Modified Bottoming 6
B16.9-2001 7/23/01 2:40 PM Page 1 ASME B16.9-2001 …
www.trubotvod.ruan american national standard factory-made wrought buttwelding fittings asme b16.9-2001