Sto Gold Coat
AATCC 127 (modified) No cracking of the coating or bond failure, no water penetration after cyclic weathering & 5 hour water column (21.5 in [55 cm]) Pass Adhesion to ASTM E2570/C297 > 15 psi (103 kPa) > 15 psi (105 kPa) over glass mat gypsum sheathing > 50 psi (345 kPa) over CMU, OSB & plywood sheathing Air Leakage Resistance
Download Sto Gold Coat
Information
Domain:
Source:
Link to this page:
Documents from same domain
System Bulletin StoPowerwall ExtraSeal - Sto Corp.
www.stocorp.comSystem Bulletin StoPowerwall® ExtraSeal™ Portland cement stucco directly applied to CMU with continuous air and moisture barrier and high performance finish
SAFETY DATA SHEET - Sto Corp.
www.stocorp.com1.3 Details of the Supplier of the Safety Data Sheet . ... for total dust and 5 mg/m of ... are advised to make your own determination as to safety, ...
StoTherm EIFS: Installation Guide - Sto Corp.
www.stocorp.com9 TheStoGuardassemblyconsistsof: Sto Gold Fill ® –Aflexible,trowel-appliedjoint treatmentthat,combinedwithStoGuard MeshorSto DetailMesh,bridgessheathingjointsandprotectsrough
Sto Guide Specification QS200D StoQuik® Silver DrainScreen ...
www.stocorp.comB. APA Engineered Wood Association PS 1 Voluntary Product Standard, Structural Plywood PS 2 Performance Standard for Wood-Based Structural-Use Panels E 30 APA Engineered Wood Construction Guide C. ICC (International Code Council) 2012 and 2015 IBC (International Building Code) D. ICC ES (International Code Council Evaluation Service) ...
StoTherm EIFS: Installation Guide - Sto Corp.
www.stocorp.comSto is the innovative world leader in cladding, coating and restoration systems. Sto was an Exterior Insulation and Finish Systems pioneer - introducing StoTherm ® to Europe in 1963. Headquartered in Atlanta, Georgia, ISO 9001:2000 and 14001:2004 Certified Sto Corp., continues to lead the North American industry in
StoTherm EIFS: Installation Guide - Sto Corp.
www.stocorp.com2 Stoistheinnovativeworldleaderincladding,coatingandrestorationsystems. StowasanExteriorInsulationandFinishSystemspioneer-introducingStoTherm® toEuropein1963 ...
StoTherm ci XPS Booklet - Sto Corp.
www.stocorp.comAll trim and projecting architectural features must have a minimum 1:2 (27 degree) slope. A minimum of ¾” (19mm) XPS insulation board must remain if areveal is cut in the insulation board. A minimum of 1 ½” thickness of XPS board is needed when a reveal is specified.
Job Description Title: Maintenance Mechanical Technician ...
www.stocorp.comJob Description. Title: Maintenance Mechanical Technician Location: Atlanta, GA Plant Reports to: Plant Engineering/ Maintenance Manager Purpose: This position will support operations by maintaining, troubleshooting, repairing and optimizing all facilities and manufacturing equipment including but not limited to:
Stolit Acrylic Textured Finish - Sto Corp.
www.stocorp.comAbrasion resistance Coverages may vary depending on application technique and surface conditions. Packaging 5 gal pail (19L). Shelf Life 18 months, if properly sealed and stored. Storage Protect from extreme heat [90ºF (32ºC)], freezing, and direct sunlight. REPORT TEST METHOD TEST CRITERIA TEST RESULTS Surface Burning ASTM E-84 < 25 Flame Spread
Expanded Polystyrene (EPS) Insulation Board
www.stocorp.com4. Projections – Insulation board shall be free of surface projections or wire marks in excess of 1/16 inches (1.6 mm). Packaging All insulation board shall be packaged in polyethylene bags as required by the EIFS manufacturer. Alternative methods of packaging shall be submitted to the EIFS manufacturer and approved in writing prior to use.
Related documents
SCIENCE CITATION INDEX EXPANDED - JOURNAL LIST …
bezmialem.edu.tr5. aatcc review 6. abdominal imaging 7. abhandlungen aus dem mathematischen seminar der universitat hamburg 8. abstract and applied analysis 9. abstracts of papers of the american chemical society 10. academic emergency medicine 11. academic medicine 12. academic pediatrics 13. academic radiology 14. accountability in research-policies and ...
AAMA 611-98 Voluntary Specification for Anodized ...
aluminium-guide.comAATCC - American Association of Textile Chemists and Colorists ASTM - American Society for Testing and Materials CMC - Color Measurement Committee of the Society of Dyers and Colorists ISO - International Organization for Standardization 5.0 GENERAL 5.1 To meet this specification, products tested shall meet all
Colorfastness to Light - Contract Textiles
contracttextiles.orgAATCC 16 Option 1 or 3* The AATCC 16 Option 1 and 3 are test methods of the American Association of Textile Chemists and Colorists (AATCC). ACT recognizes both methods where the only difference is the light source being used. In AATCC 16 Option 1 a Carbon-Arc lamp is used as the light source, and in AATCC 16 Option 3 a Xenon-Arc lamp is used.
INSULATION FOR THE BUILDING ENVELOPE
usa.sika.com(ASTM E331, AATCC Test Method 127) • Class A Flame Spread and Smoke Developed Indices per IBC Chapter 8, Interior Finishes (1” min.) • 1, 2, 3 or 4 hour Fire Rated Assemblies as shown in the UL Fire Resistance Directory. NOTE: For details, requirements and/or limitations, refer to Third-Party Evaluation Reports