SURFACE MOUNT MICRO HEADER 8 - Samtec
Board Lock (Boards are positively locked and cannot be unmated) –EJ = Ejector Shroud (Style –01 only) –DH & –MT not available 10 pins/row minimum 25 pins/row maximum –K = Keying Shroud for mating with FFSD (Style –01 only, 05 thru 25 pins/row only. 13, 17, 20 & 25 only with –EJ option) (-DV only) –A = Alignment Pin (–DV 3 ...
Download SURFACE MOUNT MICRO HEADER 8 - Samtec
Information
Domain:
Source:
Link to this page:
Documents from same domain
REVISION CF SSW-1XX-XX-XXX-X-XX-XXX-XX
suddendocs.samtec.comthis document contains confidential and proprietary information and all design, manufacturing, reproduction, use, patent rights and sales rights are expressly reserved by …
HIGH MATING FTSH–125–01L–DVEJ CYCLES SMT …
suddendocs.samtec.com(1.27 mm) .050" FTSH–125–01L–DVEJ FTSH–120–01F–DV FTSH110–01–L–DV m . A Sm . Cm m m Sm Sm m . WWW.SAMTEC.COM For complete specifications and
POWER AND VOLTAGE RATING - Samtec …
suddendocs.samtec.comVOLTAGE and POWER Ratings final 101207.doc 1 OF 13 10/18/2007 D-SCOPE-TECH, INC. POWER AND VOLTAGE RATING SCOPE: The purpose of this document is to take the confusion out of power and voltage ratings in
(1.27 mm) .050 FTS SERIES MICRO LOW-PROFILE …
suddendocs.samtec.com(1.27 mm) .050" FTS SERIES FTS1102L FTS11002FV FTS12201FV FTS11102LVSA Mates with socket strips or IDC cable Impedance matched for high-speed applications
REVISION AO FFSD-XX-X-XX.XX-01-X-X-XXX
suddendocs.samtec.comthis document contains confidential and proprietary information and all design, manufacturing, reproduction, use, patent rights and sales rights are expressly reserved by …
SFM110–02–L–D–A SFML125–T2–LD–LC …
suddendocs.samtec.com(1.27 mm) .050" SFML125–T2–LD–LC SFM–125–02–L–SH SFM110–02–L–D–A SFML115–T2–LD–LC Choice of SMT or through-hole tails Locking feature
HIGH MATING CYCLES THROUGH-HOLE MICRO …
suddendocs.samtec.com(1.27 mm) .050" FTSH SERIES Im m f applications ( CLP S) sock ips IC le T r surf m (2.51 mm) .0" O (1.27 mm) .050" m FTSH–120–02–L–D FTSH–120–01–L–D–RA
REVISION J - Samtec Microelectronics
suddendocs.samtec.com1.95049.53.05001.270.45011.43.0350.89 (typ) cl cl 01 all dimensions are symmetric about the centerline. notes: stencil to be .0060[.152] thick. a k j h
HIGH MATING CYCLES HTSW115–05–LQ TSW–209–09F–SRA …
suddendocs.samtec.comtsw, htsw series tsw–112–07–g–t tsw10910–f–d–ra htsw12013–t–d tsw–11416g–sre, , m . a sm . cm m m sm sm m .
HIGH MATING CYCLES LOW-PROFILE DUAL WIPE SOCKET
suddendocs.samtec.com(1.27 mm) .050" CLP SERIES T Cw contacts CLP–107–02–F–D–P CLP–130–02–L–D CLP–116–02–F–DH CLP–115–02–L–D S m Lw-pro˜le
Related documents
HIGH MATING CYCLES THROUGH-HOLE MICRO HEADER
suddendocs.samtec.com9 pins/row min. –EL = End Shroud with Board Lock (Style –02 & –03) 9 pins/row min. –EJ = Ejector Shroud (Style –01 only) 10 pins/row min. 25 pins/row max. –RA not available –K = Keying Shroud for mating with FFSD (Style –01 only, 05, 08, 10, 13, 15, 17, 20 & 25 pins/row only and 13, 17, 20 & 25 only with –EJ option) Specify ...
Compact I/O 1769-IF8 Analog Input Module Installation ...
literature.rockwellautomation.comwith female pins 5b stationary bus connector with male pins 6 nameplate label 7a upper tongue-and-groove slots 7b lower tongue-and-groove slots 8a upper DIN rail latch ... open and lock into place. Replacing a Single Module within a System The module can be replaced while the system is mounted to a panel (or DIN rail).
STM32 microcontroller GPIO configuration for hardware ...
www.st.com: GPIO port configuration lock register. GPIOx_AFRL: GPIO alternate function low register. GPIOx_AFRH: GPIO alternate function high register. GPIOx_ASCR: GPIO port analog switch control register. 3 GPIO main features. STM32 GPIO exhibits the following features: • Output states: push-pull, or open drain + pull-up / pull-down according to ...
Safety Wire - Federal Aviation Administration
www.faa.govastle nuts require a cotter pin to lock them down. Keep it Locked. There are three basic methods to prevent the disengagement of hardware or components: 1) safety wire, 2) cotter pins, and 3) self-locking nuts. Wire: usually stainless steel, used on cylinder studs, control cable turnbuckles, and engine accessory attaching bolts.
Inspiron 3847 Owner's Manual - Dell
downloads.dell.comconnector pins. When connecting cables, make sure that the connectors and ports are correctly oriented and aligned. CAUTION: To disconnect a network cable, first unplug the cable from your computer and then unplug the cable from the network device. CAUTION: Press and eject any installed card from the media-card reader. Recommended Tools