Technical Data Sheet
2920;2401 1 2920 epoxy ^(ValidationDate) Technical Data Sheet Penguard Express ZP Product description This is a two component amine cured epoxy coating. It is a fast drying, zinc phosphate pigmented, high solids, high build product. Specially designed for new construction where short dry to handle and over coating times are required.
Download Technical Data Sheet
Information
Domain:
Source:
Link to this page:
Documents from same domain
Technical Data Sheet - Jotun
www.jotun.comTechnical Data Sheet Hardtop Flexi The provided data is typical for factory produced products, subject to slight variation depending on colour. Gloss description: According to …
Technical Data Sheet Application Guide
www.jotun.comEpoxy HR Product description This is a two component polyamine cured phenolic/novolac epoxy coating. It is heat resistant up to 205 °C (401 °F) and can be applied on hot substrates up to 150 °C (302 °F).
Technical Data Sheet
www.jotun.comTechnical Data Sheet Epoxy HR Surface preparation summary table Substrate Minimum Recommended Carbon steel St 2 (ISO 8501-1) Sa 2½ (ISO 8501-1) Stainless steel The surface shall be hand or machine
Technical Data Sheet Application Guide
www.jotun.comApplication Guide 3140;3240;4320 1,2 3140 Scope The Application Guide offers product details and recommended practices for the use of the product. The Application Guide (AG) must be read in conjunction with the relevant specification, Technical Data Sheet (TDS) and Safety Data Sheet (SDS) for all the products used as part of the coating system.
Technical Data Sheet - Jotun
www.jotun.comOptimum performance, including adhesion, corrosion protection, heat resistance and chemical resistance is achieved with recommended surface preparation. Date of issue:22 March 2021 Page: 3/7 This Technical Data Sheet supersedes those previously issued.
Technical Data Sheet - Jotun
www.jotun.comPackaging (typical) The volume stated is for factory made colours. Note that local variants in pack size and filled volumes can vary due to local regulations. Size of containers (litres) Aluminium Paint H.R. 5 5 Storage Volume (litres) Depending on the actual exposure of the coating system, various primers and topcoats can be used in
Technical Data Sheet Jotamastic 87 Aluminium
www.jotun.comPackaging (typical) The volume stated is for factory made colours. Note that local variants in pack size and filled volumes can vary due to local regulations. Size of containers Jotamastic 87 Wintergrade Comp B 4 5 (litres) Jotamastic 87 Standard Comp B 2.7 Jotamastic 87 Aluminium Comp A 14.7 20 3 Volume (litres) Date of issue:27 June 2017 Page ...
Technical Data Sheet
www.jotun.comLEED®v4 (2013) MR credit: Building product disclosure and optimization - Material Ingredients, Option 2: Material Ingredient Optimization, International Alternative Compliance Path - REACH optimization: Fully inventoried chemical ingredients to 100 …
SAFETY DATA SHEET - Jotun
www.jotun.com1.3 Details of the supplier of the safety data sheet Product type :Liquid. Product description :Paint. 1.2 Relevant identified uses of the substance or mixture and uses advised against SECTION 1: Identification of the substance/mixture and of the company/ undertaking Product code :3140 1.4 Emergency telephone number SAFETY DATA SHEET
SAFETY DATA SHEET - Jotun
www.jotun.comSee Annex to the Safety data sheet for additional information in the Exposure Scenario(s). Consumer applications, Industrial applications, Professional applications, Used by spraying. See Section 11 for more detailed information on health effects and symptoms.
Related documents
Material Corrosion Resistance Guide - Fluid Technology
www.fluid-technology.comAluminum Stainless 304 Stainless 316 Carbon Steel Monel Neoprene Teflon Viton Interplastics 8441 Hetron FR992 Dow 510A Epoxy (250 °F) Inorganic Zinc (150 °F) Coal Tar Epoxy (300 °F) PLASITE 7122L (HAR, TFE) Potassium Hydroxide, to 25% N G G F G G G G - 150S 150S G N G G Potassium Hypochlorite - N F N N F - - - - - G - - -
Corus Construction & Industrial - NPL
resource.npl.co.ukEpoxy primer High build epoxy MIO 60µm E8 30.00 30+ 20-25 15 – Blast clean to Sa 3 150µm 50µm Recoatable polyurethane finish Sprayed aluminium to BS EN 22063 (note 7). Zinc phosphate epoxy sealer coat High build epoxy MIO A corrosion protection guide 4 For steelwork exposed to atmospheric environments
Intercure 200HS - AkzoNobel
international.brand.akzonobel.comSep 22, 2015 · A two component, high solids, low VOC, epoxy zinc phosphate/micaceous iron oxide primer offering excellent barrier protection, low temperature cure and rapid overcoating properties. PRODUCT DESCRIPTION As a primer for steelwork intended for use in a wide range of environmental conditions including
STUDBOLT FASTENERS
www.allfasteners.com.auPO Phosphate & Oil Codes Finishes & Coatings B7 / B7M Heavy Hex Bolts see page 37 plating will eliminate hydrogen embrittlement problems and blocked threads that can occur with fasteners that are exposed to increased pressure and temperature. ZINC NICKEL Zinc Nickel is recognised as a environmentally safe alternative to other electroplating methods
ISO 12944 - Carboline
www.carboline.com(Zinc Phosphate) Carboguard 893 SG Epoxy Polyamide Carboguard 60 8 mils (200 microns) Epoxy Polyamide Carboguard 60 Reinforced Zinc-Rich Primer Carbozinc 808 7 mils (175 microns) Cycloaliphatic Amine Epoxy Carboguard 890 Zinc-Rich Epoxy Carbozinc 859 VOC 11 mils (275 microns)
Technical Data Sheet
www.jotun.com20920;16620 1 20920 epoxy ^(ValidationDate) Technical Data Sheet Penguard HSP ZP Product description This is a two component amine cured epoxy coating. It is a fast drying, zinc phosphate pigmented, high solids, high build product. Specially designed for new construction where short dry to handle and over coating times are required.
CORROSION CONTROL Methods of combating corrosion ...
www.kau.edu.saSteel is coated with a layer of iron phosphate by dipping in a solution containing phosphoric acid and zinc phosphate. The iron phosphate film is not highly protective because it is porous so it usually covered with paint. The phosphate film improves the bond between the metal and the paint. i.e. Phosphating is a pre-painting step. iii. Enamels
MATERIAL & FINISH SPECIFICATIONS
www.seastrom-mfg.comPhosphate: PH MIL-DTL-16232, Type M, Classes 1 to 4 Silver Plate: S ASTM B700, Types I, II, III and Grades A to D, Class N or S Tin Plate: T1 ASTM B545, Classes A to F, Matte, Bright or Flow Brightened Zinc Plate: Z2 & Z3 ASTM B633, SC1 to SC4 and Types I to VI 1074-1095 Spring Steel HR15N 80-83 Beryllium Copper HR15N 73-79