Technical Data Sheet
Drying and curing times are determined under controlled temperatures and relative humidity below 85 %, and at average of the DFT range for the product. For storage of crude oil and clean petroleum products the tanks can be returned to service 48 hours after application of the final coat, when applied at temperatures 23 °C and above.
Download Technical Data Sheet
Information
Domain:
Source:
Link to this page:
Documents from same domain
Technical Data Sheet - Jotun
www.jotun.comTechnical Data Sheet Hardtop Flexi The provided data is typical for factory produced products, subject to slight variation depending on colour. Gloss description: According to …
Technical Data Sheet Application Guide
www.jotun.comEpoxy HR Product description This is a two component polyamine cured phenolic/novolac epoxy coating. It is heat resistant up to 205 °C (401 °F) and can be applied on hot substrates up to 150 °C (302 °F).
Technical Data Sheet
www.jotun.comTechnical Data Sheet Epoxy HR Surface preparation summary table Substrate Minimum Recommended Carbon steel St 2 (ISO 8501-1) Sa 2½ (ISO 8501-1) Stainless steel The surface shall be hand or machine
Technical Data Sheet Application Guide
www.jotun.comApplication Guide 3140;3240;4320 1,2 3140 Scope The Application Guide offers product details and recommended practices for the use of the product. The Application Guide (AG) must be read in conjunction with the relevant specification, Technical Data Sheet (TDS) and Safety Data Sheet (SDS) for all the products used as part of the coating system.
Technical Data Sheet - Jotun
www.jotun.comOptimum performance, including adhesion, corrosion protection, heat resistance and chemical resistance is achieved with recommended surface preparation. Date of issue:22 March 2021 Page: 3/7 This Technical Data Sheet supersedes those previously issued.
Technical Data Sheet - Jotun
www.jotun.comPackaging (typical) The volume stated is for factory made colours. Note that local variants in pack size and filled volumes can vary due to local regulations. Size of containers (litres) Aluminium Paint H.R. 5 5 Storage Volume (litres) Depending on the actual exposure of the coating system, various primers and topcoats can be used in
Technical Data Sheet Jotamastic 87 Aluminium
www.jotun.comPackaging (typical) The volume stated is for factory made colours. Note that local variants in pack size and filled volumes can vary due to local regulations. Size of containers Jotamastic 87 Wintergrade Comp B 4 5 (litres) Jotamastic 87 Standard Comp B 2.7 Jotamastic 87 Aluminium Comp A 14.7 20 3 Volume (litres) Date of issue:27 June 2017 Page ...
Technical Data Sheet
www.jotun.comLEED®v4 (2013) MR credit: Building product disclosure and optimization - Material Ingredients, Option 2: Material Ingredient Optimization, International Alternative Compliance Path - REACH optimization: Fully inventoried chemical ingredients to 100 …
Technical Data Sheet
www.jotun.comThis is a two component amine cured epoxy coating. It is a fast drying, zinc phosphate pigmented, high solids, high build product. Specially designed for new construction where short dry to handle and over coating times are required. Can be used as primer, mid coat, finish coat or as single coat system in atmospheric environments.
SAFETY DATA SHEET - Jotun
www.jotun.com1.3 Details of the supplier of the safety data sheet Product type :Liquid. Product description :Paint. 1.2 Relevant identified uses of the substance or mixture and uses advised against SECTION 1: Identification of the substance/mixture and of the company/ undertaking Product code :3140 1.4 Emergency telephone number SAFETY DATA SHEET
Related documents
REFERENCE CHART: HOLDING TIME, BOTTLE TYPE, …
caltestlabs.com1000 mL required for RL of 5 mg/L. 250 mL bottle recommended for samples with expected concentrations of 20 mg/L or higher. {11} If unpreserved, must be analyzed within 7 days of sampling {12} Hold time can be extended to 14 days if preserved to pH 4-5 at time of collection.
Report on Stablecoins
home.treasury.govin normal times and in periods of stress, could increase the likelihood of stablecoins supporting beneficial payments options. The recommendations in this report build on the work of international ... reportedly holding riskier reserve assets, including commercial paper, corporate and municipal bonds, and other digital assets.
Recommended Practices for Local Postweld Heat Treatment
parstechnic.comRecommended practices are available for pressure vessels(l) and piping (2) which provide in- ... for times longer than those associated with stress relief annealto form a thick ... the material where the holding temperature equals or exceeds the minimum and equals
UNDERSTANDING THE TIMES Published by Summit …
understandingthetimes.comThe website addresses recommended throughout this book are offered as a resource to you. These websites are not intended ... The book you are holding has a very long story. It began when I was a junior in college ... edition of Understanding the Times was the finished product of that sorting-out process.
ALS RECOMMENDED HOLDING TIMES AND …
www.alsglobal.comALS RECOMMENDED HOLDING TIMES AND PRESERVATIONS FOR WATER ORGANICS - SEMIVOLATILE COMPOUNDS (SVOCS) Parameter Container Preservation Holding Time Reference Acrylamide Amber (T) Chill 7 days USEPA SW846 8316 1998 Alkyl phenol Ethoxylates Amber (T) Chill 2 days AS/NZS 5667.1:1998 Chill, submit in 2 days, preserve in Lab 7 days In …
CARR’s Review of CDOR: Analysis and Recommendations
www.bankofcanada.castarted moving in this direction by either holding more BAs on balance sheet stead of selling in ... to support the benchmark in both normal times as well as stress periods. Both of these issues ... until CDOR’s recommended cessation date of June 30, 2024.