TECHNICAL DATA SHEET - DiversiTech
DOC32214 www.diversitech.com 1.800.995.2222 TECHNICAL DATA SHEET Product Purpose Features CVENT-2 2” 34 3/4“ 3 1/2” 19 1/2“
Download TECHNICAL DATA SHEET - DiversiTech
Information
Domain:
Source:
Link to this page:
Documents from same domain
CARBON MONOXIDE DETECTOR REQUIREMENTS …
media.diversitech.comcarbon monoxide detector requirements by state ... ark. code ann. § 4-86-109 ... carbon monoxide detector requirements by state
MATERIAL SAFETY DATA SHEET - DiversiTech
media.diversitech.comMaterial Safety Data Sheet Page 1 of 6 Section 1: Product & Company Identification Product Name: Zinc-It® Instant Cold Galvanize Product Number (s): 18412, 18412-6
Pro-Blue - DiversiTech
media.diversitech.comSAFETY DATA SHEET DiversiTech Corporation Chemical Emergency: P 800-255-3924 Pro-Blue™
Pro-GreenTM - DiversiTech
media.diversitech.comSAFETY DATA SHEET DiversiTech Corporation Chemical Emergency: P 800-255-3924 6650 Sugarloaf Parkway P 678.542.3600 Duluth, GA 30097 Page 1 of 5 F 678.542.3700
Vent termination Kits - DiversiTech
media.diversitech.comVent termination Kits All Fittings included DiversiTech’s CVENT series concentric vent kit includes all fittings a contractor will need to install the vent.
INSTALLATION ol.indd 1 2/1/05 4:19:25 PM - DiversiTech
media.diversitech.comThe contacts of the Wet Switch’s relay may be wired to use multiple Wet Switches. The drawing to the right shows the contacts 6650 Sugarloaf Parkway interrupting the 24 VAC signal when either Wet Switch gets wet. Duluth, GA USA 800.995.2222 678.542.3700 FAX www.diversitech.com SPECIFICATIONS:
Concentric Vent Installation Guide - DiversiTech
media.diversitech.comInstallation Guide 4010793 Certified to ULC Std S636. General ... PVC solvent cements and all primers must not be used ... 2. Determine correct Concentric Vent size for the pipe diameter selected. 3. Determine the best location for the Concentric Vent. Use 4. Cut a 4” diameter hole for CVENT-2, 2” kit.
Igniter Cross Reference - DiversiTech
media.diversitech.comigniter cross reference ign-001 ign-001 company o.e.m. or distributor part# ign-1f 700-3 ign-1r 700-4 ign-2 700-5 780-001 universal silicon
Related documents
Appendix: Ridge Vent/Soffit Vent Calculator for …
www.bestmaterials.comto create a flow of air. In addition, this standard assumes a proper balance of exhaust and intake venting. Unfor-tunately, it’s probably safer to assume that assumption
VENT SILENCERS - noise enclosures - blowers
www.eiwilliams.comINFORMATION ON VENT SILENCERS 1 A vent silencer or a blow off silencer is a device used to reduce unwanted noise created by gas or steam flow in a
1CT0302 / 1CT0303 CONCENTRIC VENT …
www.upgnet.com1ct0302 / 1ct0303 concentric vent termination for use with all condensing gas furnace models accessory kit installation instructions 035-14287-000 / 66641-uim-f-0905
SRV Vent Connectors
www.americanboa.comBOA SAFETY RELIEF VALVE VENT CONNECTORS, (SRV’s), consist of three basic elements. • A BOA multiple-ply bellows. • An external, heavy wall pressure shell. • An inner, heavy wall, full bore liner.
Sizing - Vent-Axia
www.vent-axia.comPart F&L Guide Part L Overview Part L, the document covering fuel and power is where the energy efficiency information on ventilation is covered.
To Vent or Not to Vent - Advanced Energy
www.advancedenergy.orgTo Vent or Not to Vent Kenton Pass, Contributing Editor 09/01/2004 The 2003 International Residential Code, Section R408.1 states, "The underfloor space between the bottom of the floor joists and
Emergency Relief Vent with Vacuum
www.emerson.comIntroduction Enardo™ 2500 Series emergency relief vents are designed to provide an emergency pressure relief opening for storage tanks when exposed to
Type B Vent H&C Draft 151215 - Hart and Cooley
www.hartandcooley.comType B Gas Vent - 3” to 12” Diameter Installation Instructions 1 Please read and understand the requirements before proceeding. Hart & Cooley Type B gas vent …
The Dryer Vent Requirements For Residential …
www.professionalhomeinspection.netThe Dryer Vent Requirements For Residential Housing Fall Under The “California” Uniform Mechanical Code Sections 504.1 and 504.3 Section 504.3.1 Dryer venting shall terminate on the exterior of the building and