Technical Data Sheet - Jotun
for properly prepared carbon steel, galvanized steel, shop primed steel, stainless steel, aluminum and concrete substrates. Suitable as maintenance coating on a wide range of aged coating surfaces. It can be applied at sub zero surface temperatures. Approvals and certificates Approved for PSPC for Water Ballast Tanks according to IMO Res. MSC ...
Download Technical Data Sheet - Jotun
Information
Domain:
Source:
Link to this page:
Documents from same domain
Technical Data Sheet - Jotun
www.jotun.comTechnical Data Sheet Hardtop Flexi The provided data is typical for factory produced products, subject to slight variation depending on colour. Gloss description: According to …
Technical Data Sheet Application Guide
www.jotun.comEpoxy HR Product description This is a two component polyamine cured phenolic/novolac epoxy coating. It is heat resistant up to 205 °C (401 °F) and can be applied on hot substrates up to 150 °C (302 °F).
Technical Data Sheet
www.jotun.comTechnical Data Sheet Epoxy HR Surface preparation summary table Substrate Minimum Recommended Carbon steel St 2 (ISO 8501-1) Sa 2½ (ISO 8501-1) Stainless steel The surface shall be hand or machine
Technical Data Sheet Application Guide
www.jotun.comApplication Guide 3140;3240;4320 1,2 3140 Scope The Application Guide offers product details and recommended practices for the use of the product. The Application Guide (AG) must be read in conjunction with the relevant specification, Technical Data Sheet (TDS) and Safety Data Sheet (SDS) for all the products used as part of the coating system.
Technical Data Sheet - Jotun
www.jotun.comOptimum performance, including adhesion, corrosion protection, heat resistance and chemical resistance is achieved with recommended surface preparation. Date of issue:22 March 2021 Page: 3/7 This Technical Data Sheet supersedes those previously issued.
Technical Data Sheet - Jotun
www.jotun.comPackaging (typical) The volume stated is for factory made colours. Note that local variants in pack size and filled volumes can vary due to local regulations. Size of containers (litres) Aluminium Paint H.R. 5 5 Storage Volume (litres) Depending on the actual exposure of the coating system, various primers and topcoats can be used in
Technical Data Sheet Jotamastic 87 Aluminium
www.jotun.comPackaging (typical) The volume stated is for factory made colours. Note that local variants in pack size and filled volumes can vary due to local regulations. Size of containers Jotamastic 87 Wintergrade Comp B 4 5 (litres) Jotamastic 87 Standard Comp B 2.7 Jotamastic 87 Aluminium Comp A 14.7 20 3 Volume (litres) Date of issue:27 June 2017 Page ...
Technical Data Sheet
www.jotun.comLEED®v4 (2013) MR credit: Building product disclosure and optimization - Material Ingredients, Option 2: Material Ingredient Optimization, International Alternative Compliance Path - REACH optimization: Fully inventoried chemical ingredients to 100 …
Technical Data Sheet
www.jotun.comThis is a two component amine cured epoxy coating. It is a fast drying, zinc phosphate pigmented, high solids, high build product. Specially designed for new construction where short dry to handle and over coating times are required. Can be used as primer, mid coat, finish coat or as single coat system in atmospheric environments.
SAFETY DATA SHEET - Jotun
www.jotun.com1.3 Details of the supplier of the safety data sheet Product type :Liquid. Product description :Paint. 1.2 Relevant identified uses of the substance or mixture and uses advised against SECTION 1: Identification of the substance/mixture and of the company/ undertaking Product code :3140 1.4 Emergency telephone number SAFETY DATA SHEET
Related documents
RECTANGULAR DUCTS - AIC STEEL
www.aicsteel.comHR01 is supplied with various materials Galvanized steel G90 and G115 in accordance with ASTM A653, Black Steel in accordance with ASTM A366 supplied with primer paint, Stainless steel 304 and 316 in accordance with ASTM A240 and Aluminum Alloy 3003-H14 in accordance with ASTM B209.
ZINC COATINGS - American Galvanizers Association
galvanizeit.orgContinuous sheet galvanizing is also a hot-dip process, but is only applied to steel sheet, strip, and wire. A coil to coil process, steel sheet from 0.010 to 1.70 inches (0.25 mm to 4.30 mm) thick and up to 72 inches (1,830 mm) wide is passed as a continuous ribbon through cleaning baths and molten zinc at speeds up to 600 feet per minute.
SHEET METAL DESIGN GUIDE. - GoProto, Inc.
goproto.comALUMINUM Galvanized steel is steel coated with zinc during a zinc solution heat batch. This process protects the steel from corrosion and cracks and, like aluminum, has a good strength-to-weight ratio. Galvanized steel has a lower cost per pound than aluminum but may have some issues in adhesion of paints depending on end use.
SPIRAL DUCT & FITTINGS - Eastern Sheet Metal
www.easternsheetmetal.comGauge selection for galvanized steel (ASTM A 653), paint grip steel, type 304 and 316 stainless steel, and Eastern Poly Coated Steel (PCS).* Fittings are …
Stick Consumable Charts - Global Industrial
www.globalindustrial.comStainless Steel Stainless steel contains a high chromium and low carbon content, and upon contact with oxygen creates a chromium oxide layer that gives passive protection against corrosion from moisture. When certain high-strength alloys such as aluminum come into contact with carbon steel, such as being brushed by carbon steel wire, a
Rigid Sheet Specifications
www.inprocorp.comB. Stainless steel top caps shall be made of #400 series stainless steel. C. Stainless steel vertical divider bars shall be #400 series stainless steel on galvanized steel. D. Aluminum top caps, inside corners, divider bars shall be extruded from 6063-T5 aluminum. 2.05 FINISHES A. Color or pattern of Palladium® Rigid Vinyl Sheet to
Gauge and Weight Chart for - Pittsburgh Air Systems
www.pittsburghairsystems.comGauge and Weight Chart for Sheet Steel, Galvanized Steel,Stainless Steel, and Al September 1st, 2004 This article provides a quick reference to gauges of material, pounds per square foot, and gauge decimal equivalents. Gauge Sheet Steel Galvanized Steel Stainless Steel Aluminum Gauge Decimal Lbs. per Sq. Ft. Gauge Decimal Lbs. per Sq. Ft. Gauge ...