Technical Data Sheet - Jotun
Drying and Curing time Surface (touch) dry Walk-on-dry 16 h11 h4 h2 h1 h30 min 38 h24 h10 h6 h3 h2 h 21 d13 d8 d4 d3 d Substrate temperature 0 °C5 °C10 °C23 °C40 °C Dried/cured for service-5 °C Dry to over coat, minimum 24 h14 h8 h4 h2 h1 h Walk-on-dry: Minimum time before the coating can tolerate normal foot traffic without permanent marks,
Download Technical Data Sheet - Jotun
Information
Domain:
Source:
Link to this page:
Documents from same domain
Technical Data Sheet - Jotun
www.jotun.comTechnical Data Sheet Hardtop Flexi The provided data is typical for factory produced products, subject to slight variation depending on colour. Gloss description: According to …
Technical Data Sheet Application Guide
www.jotun.comEpoxy HR Product description This is a two component polyamine cured phenolic/novolac epoxy coating. It is heat resistant up to 205 °C (401 °F) and can be applied on hot substrates up to 150 °C (302 °F).
Technical Data Sheet
www.jotun.comTechnical Data Sheet Epoxy HR Surface preparation summary table Substrate Minimum Recommended Carbon steel St 2 (ISO 8501-1) Sa 2½ (ISO 8501-1) Stainless steel The surface shall be hand or machine
Technical Data Sheet Application Guide
www.jotun.comApplication Guide 3140;3240;4320 1,2 3140 Scope The Application Guide offers product details and recommended practices for the use of the product. The Application Guide (AG) must be read in conjunction with the relevant specification, Technical Data Sheet (TDS) and Safety Data Sheet (SDS) for all the products used as part of the coating system.
Technical Data Sheet - Jotun
www.jotun.comOptimum performance, including adhesion, corrosion protection, heat resistance and chemical resistance is achieved with recommended surface preparation. Date of issue:22 March 2021 Page: 3/7 This Technical Data Sheet supersedes those previously issued.
Technical Data Sheet - Jotun
www.jotun.comPackaging (typical) The volume stated is for factory made colours. Note that local variants in pack size and filled volumes can vary due to local regulations. Size of containers (litres) Aluminium Paint H.R. 5 5 Storage Volume (litres) Depending on the actual exposure of the coating system, various primers and topcoats can be used in
Technical Data Sheet Jotamastic 87 Aluminium
www.jotun.comPackaging (typical) The volume stated is for factory made colours. Note that local variants in pack size and filled volumes can vary due to local regulations. Size of containers Jotamastic 87 Wintergrade Comp B 4 5 (litres) Jotamastic 87 Standard Comp B 2.7 Jotamastic 87 Aluminium Comp A 14.7 20 3 Volume (litres) Date of issue:27 June 2017 Page ...
Technical Data Sheet
www.jotun.comLEED®v4 (2013) MR credit: Building product disclosure and optimization - Material Ingredients, Option 2: Material Ingredient Optimization, International Alternative Compliance Path - REACH optimization: Fully inventoried chemical ingredients to 100 …
SAFETY DATA SHEET - Jotun
www.jotun.com1.3 Details of the supplier of the safety data sheet Product type :Liquid. Product description :Paint. 1.2 Relevant identified uses of the substance or mixture and uses advised against SECTION 1: Identification of the substance/mixture and of the company/ undertaking Product code :3140 1.4 Emergency telephone number SAFETY DATA SHEET
SAFETY DATA SHEET - Jotun
www.jotun.comSee Annex to the Safety data sheet for additional information in the Exposure Scenario(s). Consumer applications, Industrial applications, Professional applications, Used by spraying. See Section 11 for more detailed information on health effects and symptoms.
Related documents
Curing Concrete, Chapter 12 - Memphis
www.ce.memphis.eduCuring Concrete Fig. 12-1. Curing should begin as soon as the concrete stiffens enough to prevent marring or erosion of the sur-face. Burlap sprayed with water is an effective method for moist curing. (69973) 60 50 40 30 20 10 0 0 7 28 90 365 8 6 4 2 0 Age at test, days Moist-cured entire time In air after 28 days moist curing In air after 7 ...
The GelBottle Inc (TGB) Gel Polish / Builder in A Bottle ...
dlwdwurqx1ngf.cloudfront.netthe cuticle area. Avoid thick build-up around the free edge and the cuticle area. • Seal the free edge. • Build and cure one nail at a time, turn the hand over to help create apex if necessary. • Cure using the TGB Light The Way Lamp on low heat mode (99 seconds), the lamp has been specifically designed to cure TGB products.
PROPER ENVIRONMENT FOR POTATO STORAGE
vric.ucdavis.eduthe curing period because the heat and moisture generated by the potatoes may provide an environment that is favorable for wound healing. Do not allow free moisture (condensation) to form during storage. If that does occur, air circulation may be necessary. Thereafter, air movement may be required to maintain the desired temperature and humidity
INTRODUCTION TO POLYMERS (RESINS)
web.statler.wvu.eduCuring Agents Importance of curing agents (also called crosslinking agents, hardeners, or catalysts): • determines the type of curing reaction • influences the processing cycle: viscosity versus time, gelation • affects properties of the cured system: Tg, modulus, strength Examples of curing agents for epoxies:
Safety Tips for Using UV Curing Systems
www2.lbl.govSafety Tips for Using UV Curing Systems . What Are UV Curing Systems? UV curing is a speed curing process in which high-intensity ultraviolet (UV) light is used to create a photochemical reaction that instantly cures inks, adhesives, and coatings. Curing systems are widely used in optical, fiber-optic, electronic, laser, microelectronic, and