Technical Data Sheet - Jotun
735;739 1,2 735 phenolic/novolac ^(ValidationDate) epoxy Technical Data Sheet Tankguard Storage Product description This is a two component polyamine cured phenolic/novolac epoxy coating. It is a specially designed tank lining with excellent chemical resistance. Can be used as primer, mid coat or finish coat in atmospheric and immersed ...
Download Technical Data Sheet - Jotun
Information
Domain:
Source:
Link to this page:
Documents from same domain
Technical Data Sheet - Jotun
www.jotun.comTechnical Data Sheet Hardtop Flexi The provided data is typical for factory produced products, subject to slight variation depending on colour. Gloss description: According to …
Technical Data Sheet Application Guide
www.jotun.comEpoxy HR Product description This is a two component polyamine cured phenolic/novolac epoxy coating. It is heat resistant up to 205 °C (401 °F) and can be applied on hot substrates up to 150 °C (302 °F).
Technical Data Sheet
www.jotun.comTechnical Data Sheet Epoxy HR Surface preparation summary table Substrate Minimum Recommended Carbon steel St 2 (ISO 8501-1) Sa 2½ (ISO 8501-1) Stainless steel The surface shall be hand or machine
Technical Data Sheet Application Guide
www.jotun.comApplication Guide 3140;3240;4320 1,2 3140 Scope The Application Guide offers product details and recommended practices for the use of the product. The Application Guide (AG) must be read in conjunction with the relevant specification, Technical Data Sheet (TDS) and Safety Data Sheet (SDS) for all the products used as part of the coating system.
Technical Data Sheet - Jotun
www.jotun.comOptimum performance, including adhesion, corrosion protection, heat resistance and chemical resistance is achieved with recommended surface preparation. Date of issue:22 March 2021 Page: 3/7 This Technical Data Sheet supersedes those previously issued.
Technical Data Sheet - Jotun
www.jotun.comPackaging (typical) The volume stated is for factory made colours. Note that local variants in pack size and filled volumes can vary due to local regulations. Size of containers (litres) Aluminium Paint H.R. 5 5 Storage Volume (litres) Depending on the actual exposure of the coating system, various primers and topcoats can be used in
Technical Data Sheet Jotamastic 87 Aluminium
www.jotun.comPackaging (typical) The volume stated is for factory made colours. Note that local variants in pack size and filled volumes can vary due to local regulations. Size of containers Jotamastic 87 Wintergrade Comp B 4 5 (litres) Jotamastic 87 Standard Comp B 2.7 Jotamastic 87 Aluminium Comp A 14.7 20 3 Volume (litres) Date of issue:27 June 2017 Page ...
Technical Data Sheet
www.jotun.comLEED®v4 (2013) MR credit: Building product disclosure and optimization - Material Ingredients, Option 2: Material Ingredient Optimization, International Alternative Compliance Path - REACH optimization: Fully inventoried chemical ingredients to 100 …
Technical Data Sheet
www.jotun.comThis is a two component amine cured epoxy coating. It is a fast drying, zinc phosphate pigmented, high solids, high build product. Specially designed for new construction where short dry to handle and over coating times are required. Can be used as primer, mid coat, finish coat or as single coat system in atmospheric environments.
SAFETY DATA SHEET - Jotun
www.jotun.com1.3 Details of the supplier of the safety data sheet Product type :Liquid. Product description :Paint. 1.2 Relevant identified uses of the substance or mixture and uses advised against SECTION 1: Identification of the substance/mixture and of the company/ undertaking Product code :3140 1.4 Emergency telephone number SAFETY DATA SHEET
Related documents
Oil and Gas Pipeline Design, Maintenance and Repair - cu
www.eng.cu.edu.egPart 11: Pipeline Rehabilitation and ... Coating • A number of linings (covering the inner diameter) and coatings (covering the outer diameter) can be rolled, brushed or sprayed on the pipe to stop ... epoxy liner may be used . PE 607: Oil & Gas Pipeline Design, ...
CRE-121 White Epoxy Primer CRE-X21 SeesirP meir sr CRE …
images.oreillyauto.comCRE-121 2.1 VOC White Epoxy Primer · CRE-321 2.1 VOC Gray Epoxy Primer · CRE-921 2.1 VOC Black Epoxy Primer · CRE-2xx 2.1 VOC Tintable Epoxy Primer · CRE-211H Catalyst for CRE-X21 Primers · Exempt Solvent: Q30 - Acetone · Non-Exempt Solvents*: Q50 - Aromatic 100, Q60 - MEK, Q70 - MAK, Q80 - Xylene, Q160 - Aromatic 150 * Addition results ...
STANDARD SPECIFICATIONS for CONSTRUCTION and …
www.roads.maryland.govAug 21, 2003 · Section 464 — Epoxy Protective Coatings For Concrete 505 Section 465 — Miscellaneous Coatings For Metal (Steel) 507 ... Section 912 — Coating Systems For Structural Steel 875 Section 913 — Waterproofing 880 ... Portions of Part III Technical Requirements of these Standard Specifications for Construction and
How to Install Iron Balusters - StairSupplies™
www.stairsupplies.comsquare part going into a round hole. www.stairsupplies.com STAIRSUPPLIES Beautiful stair creations 1 866 226 6536 The small hole you see is used during the powder coating process, and doesn't affect installation. Bottom shoes are recommended, while top shoes are less common. This is because the rounded portion of the top of the baluster looks more
STANDARD HIGHWAY SPECIFICATIONS VOLUME II of II
www1.nyc.gov(2’-6”) or less, all stumps, roots and root systems shall be removed to a depth of three (3 below the ’) feet existing ground surface. In fill areas where the depth of fill varies between two foot six inches (2’-6”) and three feet (3’-0”), stumps shall be cut to provide not less than two foot six inches (2’-6”) of fill above the