Technical Data Sheet - Jotun
Specially designed as an internal lining for offshore, onshore and buried tanks and pipes such as chemical storage, waste water, grey water, process water, concrete bund, fire service lines and drilling mud tanks. ... Substrate temperature 10 °C15 °C23 °C30 °C40 °C Dried/cured for service Dry to over coat, minimum 24 h20 h10 h7 h4 h ...
Download Technical Data Sheet - Jotun
Information
Domain:
Source:
Link to this page:
Documents from same domain
Technical Data Sheet - Jotun
www.jotun.comTechnical Data Sheet Hardtop Flexi The provided data is typical for factory produced products, subject to slight variation depending on colour. Gloss description: According to …
Technical Data Sheet Application Guide
www.jotun.comEpoxy HR Product description This is a two component polyamine cured phenolic/novolac epoxy coating. It is heat resistant up to 205 °C (401 °F) and can be applied on hot substrates up to 150 °C (302 °F).
Technical Data Sheet
www.jotun.comTechnical Data Sheet Epoxy HR Surface preparation summary table Substrate Minimum Recommended Carbon steel St 2 (ISO 8501-1) Sa 2½ (ISO 8501-1) Stainless steel The surface shall be hand or machine
Technical Data Sheet Application Guide
www.jotun.comApplication Guide 3140;3240;4320 1,2 3140 Scope The Application Guide offers product details and recommended practices for the use of the product. The Application Guide (AG) must be read in conjunction with the relevant specification, Technical Data Sheet (TDS) and Safety Data Sheet (SDS) for all the products used as part of the coating system.
Technical Data Sheet - Jotun
www.jotun.comOptimum performance, including adhesion, corrosion protection, heat resistance and chemical resistance is achieved with recommended surface preparation. Date of issue:22 March 2021 Page: 3/7 This Technical Data Sheet supersedes those previously issued.
Technical Data Sheet - Jotun
www.jotun.comPackaging (typical) The volume stated is for factory made colours. Note that local variants in pack size and filled volumes can vary due to local regulations. Size of containers (litres) Aluminium Paint H.R. 5 5 Storage Volume (litres) Depending on the actual exposure of the coating system, various primers and topcoats can be used in
Technical Data Sheet Jotamastic 87 Aluminium
www.jotun.comPackaging (typical) The volume stated is for factory made colours. Note that local variants in pack size and filled volumes can vary due to local regulations. Size of containers Jotamastic 87 Wintergrade Comp B 4 5 (litres) Jotamastic 87 Standard Comp B 2.7 Jotamastic 87 Aluminium Comp A 14.7 20 3 Volume (litres) Date of issue:27 June 2017 Page ...
Technical Data Sheet
www.jotun.comLEED®v4 (2013) MR credit: Building product disclosure and optimization - Material Ingredients, Option 2: Material Ingredient Optimization, International Alternative Compliance Path - REACH optimization: Fully inventoried chemical ingredients to 100 …
Technical Data Sheet
www.jotun.comThis is a two component amine cured epoxy coating. It is a fast drying, zinc phosphate pigmented, high solids, high build product. Specially designed for new construction where short dry to handle and over coating times are required. Can be used as primer, mid coat, finish coat or as single coat system in atmospheric environments.
SAFETY DATA SHEET - Jotun
www.jotun.com1.3 Details of the supplier of the safety data sheet Product type :Liquid. Product description :Paint. 1.2 Relevant identified uses of the substance or mixture and uses advised against SECTION 1: Identification of the substance/mixture and of the company/ undertaking Product code :3140 1.4 Emergency telephone number SAFETY DATA SHEET
Related documents
Use these notes to help you fill in the Employment pages ...
assets.publishing.service.gov.ukA For information about supplying services through a company or partnership go to ... If this employer no longer exists or is offshore, do not include the details on this page. Instead, ... either at the same time or in succession, please give details on a separate sheet Car 1 Car 2 Make and model Date first registered DD MM YY Approved CO
Aqueous Film-Forming Foam (AFFF) - ITRC Web
pfas-1.itrcweb.orgThe fact sheet is not intended to replace manufacturer specifications, or industry guidance for AFFF use, or discuss alternatives in detail. It is only intended to educate users on AFFF use to reduce and eliminate potential harm to human health and the environment. For further information, please see the ITRC Technical and Regulatory
Mangroves (Primefact 746) - Department of Primary Industries
www.dpi.nsw.gov.auestuaries and bays, the sheltered bays of offshore islands and on some coral reef cays. Mangroves grow best in areas where silt is brought down by rivers or is banked up by waves, tides and currents. Mangroves usually grow in-between the mean sea level mark in the Fringing Zone, to above the mean high water mark in the Landward Zone (see Figure 5).
2021 Notice of Annual Meeting and Proxy Statement
www.ge.comUNITS Onshore Wind, Offshore Wind, Grid Solutions Equipment and Services, Hydro Solutions, Hybrids Solutions INSTALLED BASE 400+ GW of renewable energy equipment CEO Jérôme Pécresse EMPLOYEES ~40,000 PROGRESS • Onshore Wind delivered record global volumes in 2020, holding the No. 1 U.S. market position for the last two years. • Offshore ...
Technical Data Sheet - Jotun
www.jotun.comRecommended for offshore environments, refineries, power plants, bridges, buildings and mining equipment. Other Approved 1 ... The Technical Data Sheet (TDS) is recommended to be read in conjunction with the Safety Data Sheet (SDS) and the ... Substrate temperature 10 °C23 °C40 °C Dried/cured for service Dry to over coat, minimum 16 h8 h3.5 h