Technical Document Seismic Technical Guide
12 ga. hanger wire min. 3 turns Typical Saddle Tie Note: saddle tie has double loop at support Bottom of Wood Joist saddle tie required for all widths greater than 1/2" hanger wire 1/4" diameter drilled hole 2" min. typical saddle tie with double loop at support Bottom of Wood Joist 12 ga. hanger wire min. 3 turns wood I-joist add 2 1/2" x 20 ...
Download Technical Document Seismic Technical Guide
Information
Domain:
Source:
Link to this page:
Documents from same domain
USG Fire-Resistant Assemblies Catalog (English) - …
www.usg.com4 USG Fire-Resistant Assemblies Fire Protection USG is the undisputed leader among building material manufacturers in providing products and systems designed to keep people safe from fire.
USG Area Separation Wall Systems Brochure …
www.usg.comArea separation walls between adjoining townhouses must provide fire-resistive ratings to ensure the safety of occupants in adjacent dwellings.
Fire-Resistant Assemblies Brochure (English) - SA100
www.usg.comUser’s Guide Use this brochure to determine fire ratings for CGC products and systems. This brochure provides: — Comprehensive information about fire-rated assemblies
Technical Document Seismic Technical Guide - USG
www.usg.comTechnical Seismic Technical Guide Document Light Duty Suspension Systems ASTM C6351 addresses the load carrying capability of main tees, categorizing them as Light, Intermediate or Heavy Duty.
CGC SHAFT WALL SYSTEMS - USG
www.usg.comC-H studs in a progressive manner, with gypsum panels, gypsum fiber panels or cement board applied to the face. All details, specifications and data contained in this literature are intended as a …
USG DUROCK BRAND CEMENT BOARD SYSTEMS
www.usg.comSTANDARDS USG Durock® cement board exceeds ANSI standards for cementitious backer units (CBU). See ANSI A118.9 for test See ANSI A118.9 for test methods and specifications for CBU and ANSI A108.11 for interior installation of CBU.
Manual Técnico USG Tablaroca® (Español)
www.usg.comUSG Manual Técnico USG TABLAROCA® USG SHEETROCK® Manejo, almacenaje, especificación, instalación y recomendaciones generales.
0 ICC-ES Evaluation Report ESR-1222 - USG
www.usg.comThe USG suspended ceiling framing systems described in this report are suspended, exposed framing, concealed ceiling assemblies used in fire-rated and non -resistance -
Technical Document Seismic Technical Guide - USG
www.usg.comTechnical Seismic Technical Guide Document Compression Posts USG Donn® Brand Compression Post providesidrig support for a ceiling suspension system in seismic applications. Telescoping compression posts attach to the main tees at each splayed wire location, preventing upward
SET YOUR DESIGN APART. Drywall Suspension System
www.usg.com2 USG Drywall Suspension System Flat Ceilings The USG Drywall Suspension System is engineered to replace traditional framing such as steel studs or cold-rolled channel and drywall furring channel for gypsum board ceiling installations. Main tees and cross tees snap together, which reduces wire ties.
Related documents
Handbook of STEEL SIZES & WEIGHTS
www.coyotesteel.comCoyote Steel & Co. 2030 Cross Street Eugene, Oregon 97402 USA No. 1 Handbook of STEEL SIZES & WEIGHTS For Industry Phone: 541-461-2060 Toll-free: 1-800-553-0240
METAL LATH FOR STUCCO & PLASTER
amicoglobal.comAMICO Wire Corners are discussed further on page 14 (Specialty Products) Cornalath is used to reinforce corners and help prevent cracks. The 105º angle offers resistance when placed to the inside of the corner over the lath. Available in galvanized steel only. Striplath is galvanized, diamond mesh lath, produced in 6” wide strips with smooth ...
MASTER SPECIFICATIONS Division 09 FINISHES
www.northwestern.eduA. Tie Wire: ASTM A 641/A 641M, Class 1 zinc coating, soft te0.062-inch- (1.59-mmmper, -) diameter wire, or double strand of 0.048-inch- (1.21-mm-) …
From the Ground Up - ptsupply.com
www.ptsupply.comAerial Support Spacer Tie One piece ties designed for standard spacing applications. Pre-grouped in multiples of five to save installation time. Minimum tensile strength is 100 lbs. Guy-Grip® Deadends For quick, easy dead-ending of 7-wire and 3-wire “B” galvanized guy and messenger strand. Each size is color-coded for identification in ...
12TH EDITION National Gypsum Construction Guide
www.steeler.comhanger wire 1 1/2" c.r. channel tie wire 66 casing bead flexible dust seal finished wall line gypsum plaster 09210k scale: 3" = 1'-0" suspended metal lath at wall (unrestrained) hanger wire 3/4" c.r. channel 1 1/2" c.r. channel metal lath gypsum plaster no. 15 expansion joint 09210m scale: 3" = 1'-0" suspended metal lath control joint metal ...
Technical Document Seismic Technical Guide - USG
www.usg.com12 ga. hanger wire min. 3 turns Typical Saddle Tie Note: saddle tie has double loop at support Bottom of Wood Joist saddle tie required for all widths greater than 1/2" hanger wire 1/4" diameter drilled hole 2" min. typical saddle tie with double loop at support Bottom of Wood Joist 12 ga. hanger wire min. 3 turns wood I-joist add 2 1/2" x 20 ...
PDF Downloads – Specifications and Applications of Steel Wire
www.walcoom.comCoil galvanized wire. U type wire. Straight cut wire. Double loop wire ties. Single loop bale ties. Cotton bale tie wire. Table 1: Common Specifications of Hot Dipped Galvanized Wire Serial Number Size Diameter (mm) Standard Bundle Weight (Kg) 1 8# 4.0 50 2 10# 3.5 50 3 12# 2.8 50 4 14# 2.2 50 5 16# 1.6 50.25 6 18# 1.2 25 7 20# 0.9 25 8 22# 0.7 ...