Thread and Connector Identification
inch - TPI mm inch mm inch inch 5/16 - 24 UNF-05 7,9 0.31 6,9 0.27 1/8 3/8 - 24 UNF-06 9,5 0.38 8,5 0.33 3/16 7/16 - 20 UNF-07 11,1 0.44 9,9 0.39 1/4 1/2 - 20 UNF-08 12,7 0.50 11,4 0.45 5/16 9/16 - 18 UNF-09 14,3 0.56 13,0 0.51 3/8 3/4 - 16 UNF-12 19,1 0.75 17,5 0.69 1/2 7/8 - 14 UNF-14 22,2 0.88 20,3 0.80 5/8 1.1/16 - 12 UN-17 27,0 1.06 24,9 0 ...
Download Thread and Connector Identification
Information
Domain:
Source:
Link to this page:
Documents from same domain
T1A – AVENGER Non-Skive Hose AVENGER T …
www.gerrardhydraulics.com.auPage 30 QUALITY HOSE AND FITTINGS T1A – AVENGER Non-Skive Hose AVENGER T1A Meets or exceeds the performance requirements of SAE 100R1AT, AS 3791 100R1AT, DIN 20022-1SN, EN 853 Type 1SN, ISO 1436 Types R1AT & 1SN.
Guide to Thread and Connector Working Pressures
www.gerrardhydraulics.com.auimpractical to lay down specific allowable working pressures that satisfy all design criteria. Unless otherwise specified in this document, and given correct working conditions, including, but not limited to, torque setting, assembly, alignment, support,
Thread and Connector Identification
www.gerrardhydraulics.com.auJIC is JOINT INDUSTRIES COUNCIL SAE J514, ISO 8434-2 UN is UNIFIED NATIONAL SAE J1926, ISO 11926-2 JIC & UNO (O Ring Boss) thread forms are the same (ASME B1.1). Method of sealing differs. JIC male has 37° flare which seals against 37° seat in female. UNO (O Ring Boss) seals with O Ring compressed
Related documents
ICC-ES Evaluation Report ESR-3223
www.itwbuildex.com#12-14 HWH #12-14 UPFH 1/ 4-14 HWH 1/ 4-20 HWH or SI: 1 inch = 2 For shear conne spectively, mus Nominal strength Steel must comp o calculate LRF he “–” symbol d he top sheet is FIGURE ost Widely Acc TA N NOM DIAM (in H 0.1 H 0.2 H 0.2 0.2 0.2 5.4 mm, 1 lbf = 4 ections, the low design. s are based on ly with AISI S10 D values, multip ...
BAB I PENDAHULUAN 1.1 Latar Belakang
scholar.unand.ac.id1. Ron Akek Mesin boat 5 Pk 10 unit 10 orang Dusun Pogari 2. Surak Sita Mesin boat 5 Pk 14 unit 14 orang Dusun Adduru 3. Rop Akek Mesin boat 5 Pk 10 unit 10 orang Dusun Pogari Sumber: Dinas Perikanan Kepulauan Mentawai 2017 Dari tabel di atas dapat dilihat penerimaan bantuan program perikanan
Shear Strengths Comparison Grades 2, 5 & 8
site.alliedbolt.comShear Strengths Comparison Grades 2, 5 & 8 Comparison of Shear Strengths of Grade 2, 5 and 8 Screws The industry standard for determining shear strengths of fasteners is to take 60% of the minimum Ultimate Tensile Strength of the fastener for …
S. L. ten Cate 08-2015
mae.ufl.edu2” x 4,5 UNC 50,726 44,679 4,5 UNF (2A) Nominal Diameter Major Diameter (mm) Minor Diameter (mm) TPI 1/4” x 28 UNF 6,325 5,360 28 5/16” x 24 UNF 7,910 6,782 24 3/8” x 24 UNF 9,497 8,382 24 7/16” x 20 UNF 11,079 9,728 20 1/2” x 20 UNF 12,667 11,328 20 5/8” x 18 UNF 15,839 14,351 18 3/4” x 16 UNF 19,012 17,323 16 7/8” x 14 UNF ...
Standard Specification for Anchor Bolts, Steel, 36, 55, and ...
www.3ppars.com5.1.4 Grade and class. 5.1.5 Copper content, if copper bearing steel is required. 5.1.6 Size and Dimensions—Nominal diameter and thread pitch, bolt length, thread length, head type (if required) and hook angle and hook length (if required). 5.1.7 Coatings—If required, the coating process and the length to be coated as measured from the ...