Search results with tag "Sae j514"
Technical Data Pressure Ratings, General Reference - Air-Way
www.air-way.comSAE Dash Size Nom Inch Tube O.D. SAE J514 Flared Tube End and SAE J1926/3/ ISO 11926-3 O-Ring Port Thread Size 37 Deg. Flared Tube Ends, Unions and Bulkheads 37 Deg. Female Swivels SAE J514 (Inch) Port Plugs and Stud Ends Per SAE J1926/3/ISO 11926-3 Port Plugs/Non-Adjustable Studs Adjustable Studs MPa psi-2 1/8 5/16-24 UNF 34.5 5,000
37° Flared Tube Fittings (SAE J514) - Panam Engineers
www.panamengineers.comDesign & Construction SAE-J514 Assembly Instructions The SAE 37° Flared Tube Fittings design is simple. It uses an easily produced flare at the tube end to seal and hold fluid under high pressure. The fitting consists of three pieces: the body, …
螺纹管接头 (MS-01-147;rev Q;zh-CN;目录)
www.swagelok.com.cnsae j514,液压管接头或基于液压油泄漏的 4:1 设计系数的 压力测试。 统一英制螺纹 世伟洛克 an 接头 asme b1.1 unj, sae as 8879 额定值以室温下压力 pipe 管道 b31.3 和工艺管线的 asme 代码为基础。 按 b31.1 动力 pipe 管道确定压力额定值时: 碳钢材料—乘以 0.85。
Thread and Connector Identification
www.gerrardhydraulics.com.auJIC is JOINT INDUSTRIES COUNCIL SAE J514, ISO 8434-2 UN is UNIFIED NATIONAL SAE J1926, ISO 11926-2 JIC & UNO (O Ring Boss) thread forms are the same (ASME B1.1). Method of sealing differs. JIC male has 37° flare which seals against 37° seat in female. UNO (O Ring Boss) seals with O Ring compressed
37° Flared Tube Fittings (SAE J514)
superlokworld.comThe tube end is flared at a 37° angle (74°included angle) and held between the fitting nose (seat) and the sleeve (support) with the nut as shown in Fig. 3, providing a very effective (single) seal between the fitting nose and the tube flare. The design of SAE 37° Flared Tube Fittings is …
FITTINS Pipe Fittings - Swagelok
www.swagelok.comSAE J514, Hydraulic Tube Fittings or pressure testing with a 4:1 design factor based on hydraulic fluid leakage. Unified Inch Screw Threads Swagelok AN fittings ASME B1.1 UNJ, SAE AS 8879 Ratings are based on ASME Code for Pressure Piping B31.3, Process Piping, at …
Thread and Connector Identification - Gerrard Hydraulics
www.gerrardhydraulics.com.auJIC 37° FLARE & UNO (O RING BOSS) THREADS JIC is JOINT INDUSTRIES COUNCIL SAE J514, ISO 8434-2 UN is UNIFIED NATIONAL SAE J1926, ISO 11926-2 JIC & UNO (O Ring Boss) thread forms are the same (ASME B1.1). Method of sealing differs. JIC male has 37° flare which seals against 37° seat in female. UNO (O Ring Boss) seals with O Ring compressed
GUÍA DE IDENTIFICACIÓN Y MEDICIÓN DE ROSCAS
brennaninc.comLas conexiones hidráulicas SAE J514 JIC/37° son comunes en la mayoría de los sistemas hidráulicos. Tanto el componente macho como la hembra tienen un asiento de 37°. El sellado se hace estableciendo contacto entre el macho abocardado y el asiento cónico de la hembra. Esta es también considerada una conexión mecánica.
Thread Identification Guide
www.hydraulicstore.comJIC 37° Flare (SAE J514) The 37° JIC (Joint Industrial Council) is a reliable, straight thread, single-flare design that is used across the world. It is very popular in many applications and environments because it’s compact and easy to assemble. It also features high holding power with low torque requirements. The 37° JIC connection consists
CONECTORES HIDRÁULICOS
www.indisa.comEste fue desarrollado para cumplir las estrictas normas y requerimientos de SAE J514 y los estándares militares MILF 18866. Este conector consiste de un cuerpo, un casquillo (ferrule) maquinado de alta presión y una tuerca. En el ensamble el casquillo muerde la …
SAE J514 - World Wide Metric
products.worldwidemetric.com41 SAE TECHNICAL CHARACTERISTICS The CAST S.p.A. 37° fitting grants a perfect sealing of the system independently from the used fluid, as long as corrosive fluids are not used and all the specific prescription for this type of fitting are complied with.