Thread and Connector Identification
JIC is JOINT INDUSTRIES COUNCIL SAE J514, ISO 8434-2 UN is UNIFIED NATIONAL SAE J1926, ISO 11926-2 JIC & UNO (O Ring Boss) thread forms are the same (ASME B1.1). Method of sealing differs. JIC male has 37° flare which seals against 37° seat in female. UNO (O Ring Boss) seals with O Ring compressed
Download Thread and Connector Identification
Information
Domain:
Source:
Link to this page:
Documents from same domain
Thread and Connector Identification - Gerrard …
www.gerrardhydraulics.com.auPage 426 QUALITY HOSE AND FITTINGSQUALITY HOSE AND FITTINGS Thread and Connector Identification Thread size refers to the nominal bore of the pipe. Subtract approximately 1/4”(6 mm) from thread meas ure ment for nominal pipe size.
T1A – AVENGER Non-Skive Hose AVENGER T …
www.gerrardhydraulics.com.auPage 30 QUALITY HOSE AND FITTINGS T1A – AVENGER Non-Skive Hose AVENGER T1A Meets or exceeds the performance requirements of SAE 100R1AT, AS 3791 100R1AT, DIN 20022-1SN, EN 853 Type 1SN, ISO 1436 Types R1AT & 1SN.
Guide to Thread and Connector Working Pressures
www.gerrardhydraulics.com.auimpractical to lay down specific allowable working pressures that satisfy all design criteria. Unless otherwise specified in this document, and given correct working conditions, including, but not limited to, torque setting, assembly, alignment, support,
Related documents
CONECTORES HIDRÁULICOS
www.indisa.comEste fue desarrollado para cumplir las estrictas normas y requerimientos de SAE J514 y los estándares militares MILF 18866. Este conector consiste de un cuerpo, un casquillo (ferrule) maquinado de alta presión y una tuerca. En el ensamble el casquillo muerde la …
37° Flared Tube Fittings (SAE J514)
www.panamengineers.comDesign & Construction SAE-J514 Assembly Instructions The SAE 37° Flared Tube Fittings design is simple. It uses an easily produced flare at the tube end to seal and hold fluid under high pressure. The fitting consists of three pieces: the body, …
GUÍA DE IDENTIFICACIÓN Y MEDICIÓN DE ROSCAS
brennaninc.comLas conexiones hidráulicas SAE J514 JIC/37° son comunes en la mayoría de los sistemas hidráulicos. Tanto el componente macho como la hembra tienen un asiento de 37°. El sellado se hace estableciendo contacto entre el macho abocardado y el asiento cónico de la hembra. Esta es también considerada una conexión mecánica.
Thread Identification Guide
www.hydraulicstore.comJIC 37° Flare (SAE J514) The 37° JIC (Joint Industrial Council) is a reliable, straight thread, single-flare design that is used across the world. It is very popular in many applications and environments because it’s compact and easy to assemble. It also features high holding power with low torque requirements. The 37° JIC connection consists
螺纹管接头 (MS-01-147;rev Q;zh-CN;目录)
www.swagelok.com.cnsae j514，液压管接头或基于液压油泄漏的 4:1 设计系数的 压力测试。 统一英制螺纹 世伟洛克 an 接头 asme b1.1 unj， sae as 8879 额定值以室温下压力 pipe 管道 b31.3 和工艺管线的 asme 代码为基础。 按 b31.1 动力 pipe 管道确定压力额定值时： 碳钢材料—乘以 0.85。
FITTINS Pipe Fittings - Swagelok
www.swagelok.comSAE J514, Hydraulic Tube Fittings or pressure testing with a 4:1 design factor based on hydraulic fluid leakage. Unified Inch Screw Threads Swagelok AN fittings ASME B1.1 UNJ, SAE AS 8879 Ratings are based on ASME Code for Pressure Piping B31.3, Process Piping, at …