Trusses - CWC
Trusses • Introduction • Applications • Shapes • Spans • History • Materials • Design Procedures • Codes and Standards • Details • Gable Roof • Girder and Valley • Hip Roof • Truss Support • Manufacture • Quality Control • Fire Safety • Additional Info Introduction Wood trusses are widely used in single- and multi-family residential, institutional, agricultural
Download Trusses - CWC
Information
Domain:
Source:
Link to this page:
Documents from same domain
Trusses - CWC
cwc.caTrusses • Introduction • Applications • Shapes • Spans • History • Materials • Design Procedures • Codes and Standards • Details • Gable Roof • Girder and Valley
Prescriptive Residential Exterior Wood Deck Span …
cwc.ca7 canadian wood council residential prescriptive exterior wood deck span guide table 2a - deck joist spans not incised (m) maximum allowable
Fire Separations & Fire resistance Ratings
cwc.caprotection, using firestop systems. More information on firestop systems can be found in the W Fire Fact Sheet entitled “Fire Stops and Fire locks.” Fire-Resistance Ratings For an assembly or a structural member that is required to have a fire-resistance rating, Subsection 3.1.7. of the N specifies that the fire-resistance rating shall be
Prescriptive Residential Exterior Wood Deck Span Guide - CWC
cwc.ca4 DESIGN ASSUMPTIONS Joists and eams Design based on SA O86-14 and N 2015 Live load: 1.9 kPa (40 psf) Dead load: 0.5 kPa (10 psf) Grade: No.2 or better Species: Refer to Table 1 Live load deflection limit: L/360 Wet service condition factors for all Tables (Ksb = 0.84, Ksv = 0.96, KSE = 0.94) Treatment factors for incised lumber Tables (KT = 0.85 for ending and Shear, KT …
Sizes Table 2: Plywood Thicknesses - CWC
cwc.caCommon panel sizes are listed in Table 3. Panel Sizes 4' x 8', 4' x 9', 4' x 10' Sizes – Wood Ref. Handbook Canadian plywood is manufactured in several sizes and thicknesses as shown in Table 4.2 ( 197). It is most commonly available in sheets 1220mm (4') wide by 2440mm (8') long. It is also available in a metric size of 1200 x 2400mm. Other ...
Available sizes of glulam - CWC
cwc.caStandard sizes have been developed for Canadian glued-laminated timber to allow optimum ... Initial width of glulam stock Finished width of glulam stock mm. in. mm in. 89 3-1/2 80 3 140 5-1/2 130 5 184 7-1/4 175 6-7/8
Oriented Strand Board (OSB) Sizes - CWC
cwc.caOriented Strand Board (OSB) Sizes OSB panels are available in a variety of thicknesses and sizes. They are manufactured in both imperial and metric sizes, and are either square-edged or tongue-and-grooved on the long edges for panels 15 mm (19/32”) or thicker. The most common panel size is 1220 x 2440 mm (4 x 8 ).
Wood Trusses - CWC
cwc.caLight trusses are manufac-tured to suit virtually any roof profile. Pitched or flat, they are only limited to the load arrangements and the support locations. Flat Trusses: Flat trusses, also known as parallel chord trusses, are an alternative to conventional wood floor joist systems and are a competitive option to open web steel joist systems.
Cahier Pratique de Calcul et D'Estimation - CWC
cwc.ca• Disponibilité de main-d’oeuvre. • Facilité de montage et de manutention des matériaux. • Mise en œuvre plus rapide. • Options de finition. • Formes de bâtiment complexes relativement faciles à réaliser. C ahier pratique de calcul et d’estimation 1 1.0 Introduction GRID-CRA french 5/12/99 11:46 AM Page 1
Related documents
888.565.9181 • www.TrusSteel.com Truss Design Manual
www.cascade-mfg-co.comRecognized fire resistance Noncombustible TrusSteel trusses provide integral, recognized fire resistance that does not fade with time. See the following pages for a list of TrusSteel’s useful, cost-saving UL-listed roof and floor assemblies. Assured structural performance With over forty years of experience in the truss
Techincal Note: Fire-Retardant-Treated (FRT) Plywood
inspectapedia.comWhere the required fire-resistance rating is 2 hours or less. Exterior wall assemblies I & II 603.1.1.1.2 Nonbearing - where no fire rating is required. Roof constructions I & II 603.1.1.3 Including girders, trusses framing and decking. EXCEPTION: In Type I Construction exceeding two stories in height, FRT is not permitted in roof con-
Pryda’s Specifi cation Guide for Floor and Rafter Truss …
pryda.com.aupredictably reliable performance. The timber for these trusses is on fl at, which provides a stable platform during installation and minimizes the overall depth required. All trusses use commonly available timber and most fl oor trusses in …
Fire performance of trusses - Structural building components
sbcindustry.comFIRE PERFORMANCE OF TRUSSES 17-1 17.1 FIRE PERFORMANCE - INTRODUCTION Fireproof buildings do not exist. Even buildings constructed entirely of noncombustible materials can suffer complete loss due to a fire started in the contents of the building. The intention of fire performance evaluation is to provide safe structures using reasonable
2-Hour Fire Endurance Assembly for MPCWT Structural Floor ...
sbcindustry.comOct 02, 2017 · trusses with end joints centered over the top chord of the truss • Placed so the end joints are staggered • Applied in compliance with specifications and recommendations provided by ... fire performance of the membrane system and creates dead air space that is insulating.
Cold-Formed Steel Trusses: Design, Performance, and …
www.buildsteel.org3. CFS trusses deliver on performance and lifecycle savings Overall, framing and trusses represent approximately 20 percent of the total cost of construction, so any incremental additional initial cost from using CFS trusses is a minimal increase to owners. However, when you factor in the costs resulting from wood
FIRE BARRIER SYSTEM - ROCKWOOL
www.rockwool.comPerformance Fire performance N.B. All extensions in drop height must incorporate a minimum 100mm overlap between the sections and stitched with 1.5mm galvanised wire. *All stitching must be carried out using 0.9mm annealed and galvanised wire. Continuous wire stitching (100mm minimum) or separate lengths of wire secured by twisting ends together.