Search results with tag "Pryda"
FIXING & INSTALLATION OF PRYDA BUILDER'S GUIDE
www.pryda.co.nzThe Pryda timber connectors are manufactured from either Z275 or Z600 galvanised coil. Some brackets are also available in hot dipped galvanised or stainless steel for use in certain exposed and covered situations. Application Pryda timber connectors are designed for specific connections of timber to timber, primarily,
Truss Systems for Floors and Rafters - Pryda Australia
www.pryda.com.auwww.pryda.com.au Truss Systems for Floors and Rafters The high performance cost effective system using steel or timber webs 248-Pryda-Truss System Bro Update2 (Singles).indd 1 10/8/15 5:48 PM
Installation Guidelines for Timber Roof Trusses - Pryda
pryda.com.auPryda Australia acknowledges Standards Australia for permission to reproduce some of the drawings and technical content from within AS4440-2004. 1.2 APPLICATION . This document intends to apply to nailplate timber roof trusses within the following general limitations: a) Residential structures (NCC Building classes 1, 2,
Pryda’s Specifi cation Guide for Floor and Rafter Truss …
pryda.com.auPryda Span is manufactured using light gauge metal webs and are lighter than Longreach, but this is considered during the design process. The metal web system can be very cost-effective, especially if the truss chords have reserve capacity, as is often the case. The nail plates and Pryda Span metal webs are made to
Pryda Timber Connectors
www.pryda.com.auPryda Timber Connectors Bracing Guide September 2016 A complete guide to the design, specifications and installation of Pryda Bracing
Pryda Timber Connectors
www.pryda.com.auPRYDA TIMBER CONNECTORS Post Anchors Guide POST ANCHORS GUIDE – 4MARCH 2014 POST ANCHORS Economical Timber Post Anchors Advantages Pryda Post Anchors are manufactured to a consistent quality.
Pryda Timber Connectors
www.pryda.com.auPryda Timber Connectors Connectors & Tie-Downs Guide September 2016 A complete guide to the design, specifications and installation of Pryda Connectors & Tie-Downs
Pryda Timber Connectors
www.pryda.com.auPryda Timber Connectors Hangers & Truss Boot Guide September 2016 A complete guide to the design, specifications and installation of Pryda Hangers and Truss Boots
Pryda Timber Connectors
pryda.com.au• Pryda products are structurally adequate provided they are designed, installed and used completely in accordance with . This warranty applies only to: • Products in this guide. Products used in the specified applications and not damaged after manufacture and supply . • Joints free from wood splitting, decay or other timber defects
Pryda Timber Connectors
pryda.com.au4. Hole diameter for bolts in seasoned timber must not be more than 1.0 mm larger than the bolt diameterto achieve snuga - tight connection. Specified washers must be installed against the timber face. 5. Use proper safety equipment and due care in installing these connectors. 3 mm. 7. Do not over-tighten screws.
Pryda Post Anchors Guide - March 2017
pryda.com.auGenerally used to “hide” the post anchor. The post is slotted at the bottom and bolted through the post and anchor, leaving only the bolt heads, nuts and washers visible. Can be bolted to existing concrete or decking or set into concrete 9 Centre Pin Post Anchor (PSCP) For use where the post anchor is NOT to be visible. Due to the fixing
Pryda Timber Connectors
www.pryda.com.au90 39.4 65.0 52.1 86.0 3/45. Notes: 1. The Anti-crush Plate increases the bearing capacities of the wall plate only. The bearing capacities of the truss are the “Without Anti -