WEBER CARBURETOR CONVERSION KIT INSTALLATION GUIDE
• Attach the original throttle return spring to the lower lever on the Weber Carburetor. If this is not possible on your vehicle use the alternative throttle return spring and bracket provided in the kit. See picture # 9 for more details. • Locate the fuel inlet pipe (picture # 5) on the carburetor and connect the supply line to it.
Download WEBER CARBURETOR CONVERSION KIT INSTALLATION GUIDE
Information
Domain:
Source:
Link to this page:
Documents from same domain
Support - Quadratec
www.quadratec.comP7 - 52823 - Rev. 1 0713 Installation Instructions - Fabric Replacement Top for Trektop NX 2013 Bestop, Inc. Section 2 Remove Header and Fabric From Vehicle (cont.) Page 7 Step 3 Step 4 Step 3 Step 5 Step 4 Lift the Middle Bow from the slots in the Door Surround. Pull back on the quick release knob on the
Related documents
EARLY CHEVROLET PARTS
earlychevyparts.com1925-31 Carburetor Choke Spring -- State your model of carburetor EA 6.00 1925-31 Carburetor Choke Wire Connector EA 15.00 1929-31 Carburetor Choke & Throttle Cable Holder Bracket EA 28.00 1925-26 Carburetor Float -- For Carter Model RXO EA 120.00 1927-31 Carburetor Float for Carter RAJX-O, RAKX-O & RJH08 (21-29s) EA 75.00
STAINLESS VALVES - Manley Performance
manleyperformance.com6 PHONE: 732.905.3366 FAX: 732.905.3010 A Manley Valve For Every Application Choose from one of five series of stainless valves PERFORMANCE SERIES Stainless Steel (XH-422 Exhaust and NK-840 Intake) Chrome Stems and Hard Tips Swirl Polished and Fully Machined Stock and .100” Longer Lengths Available STREET SERIES Stainless Steel (XH-424 Exhaust and NK …
Genuine Parts & Quality Reproductions
www.earlyford.comDec 04, 2009 · SPOT-18552-SET SPOT LIGHT WITH ATTACHING BRACKET, 6V, with Ford name plate, includes all hardware, brackets, etc. ALL 155.25 ea. Above lights also available in 12V - specify. BUG SCREENS 128-6062 Passenger Car 33-34 35.00 ea. 128-6064 Passenger Car 35-35 35.00 ea. 128-6068 Passenger Car 36-36 35.00 ea.
8 to 18 HP Cast Iron Four Cycle Engines
www.smallenginesuppliers.com5. Remove carburetor, clean and install carburetor kit, make adjustment pre-sets where needed. Make sure fuel tank, fuel filters and fuel lines are clean. Reinstall carburetor, replacing any worn or damaged governor springs or linkage. Make proper governor adjustment. 6. Remove flywheel, check for leaks in oil seals, check flywheel key and ...
QUICKSTART MANUAL - Holley
documents.holley.comyour throttle bracket and transmission kickdown brackets. You may be able to re-use the stock style throttle stud or transmission studs from your carburetor. Throttle Linkage/Bracket Side View Figure 2 3. Reconnect the throttle and transmission kick-down linkage. Be sure to check for any binding conditions and correct before proceeding.
550-870, 550-870K, 550-871, 550-871K, 550-872, & 550-872K ...
documents.holley.comJun 09, 2020 · also the time to install your throttle bracket and transmission kickdown brackets. You may be able to re-use the stock style throttle stud or transmission studs from your carburetor. Throttle Linkage/Bracket Side View 3. Reconnect the throttle and if applicable transmission kick-down linkage. Be sure to check for any binding
Ford 2N | 8N | 9N Tractor Parts Manual
www.jensales.comfo-p-2n,8n,9n ffoorrdd parts manual 2n, 8n, 9n & naa this is a manual produced byjensales inc.without the authorization of ford or it’s successors.ford and it’s successors are not responsible for the quality or accuracy of this manual.
V H ILLUSTRATED - M-and-D.com
www.m-and-d.comCrankshaft, Piston and Connecting Rod (cont.) ITEM 24 25 26 27 28 29 30 31 32 33 34 35 36 37 PART NO. ADE65 PK52 ADR63 A DR63A N101A GH44 PL83 PA333 U212 PD123 PE66 ...