XBee /XBee-PRO RF Modules
Sep 23, 2009 · The XBee®/XBee-PRO® RF Module was designed to mount into a receptacle (socket) and there-fore does not require any soldering when mounting it to a board. The XBee Development Kits con-tain RS-232 and USB interface boards which use two 20-pin receptacles to receive modules. Figure 1‐02. XBee Module Mounting to an RS‐232 Interface Board
Download XBee /XBee-PRO RF Modules
Information
Domain:
Source:
Link to this page:
Please notify us if you found a problem with this document:
Advertisement
Documents from same domain
AT Commands Reference Guide - SparkFun …
www.sparkfun.comAT Commands Reference Guide 80000ST10025a Rev. 0 - 04/08/06 Reproduction forbidden without Telit Communications S.p.A. written authorization - All …
Guide, Reference, Command, Sparkfun, At commands reference guide
DS1307 64 x 8 Serial Real-Time Clock
www.sparkfun.com1 of 12 100101 FEATURES Real-time clock (RTC) counts seconds, minutes, hours, date of the month, month, day of the week, and year with …
Advanced User Manual - SparkFun Electronics
www.sparkfun.comusage information and a summary of common commands refer to the Install Guide for a given product. Version 4.77 August 27, 2009 Roving Networks reserves the right to make corrections, modifications, and changes to its products, documentation and services ... Advanced User Manual.
Guide, User, Electronic, Advanced, Sparkfun, Sparkfun electronics, Advanced user
Preliminary Product Specification v1 - SparkFun Electronics
www.sparkfun.comRevision 1.0 Page 3 of 75 nRF24L01+ Preliminary Product Specification Writing Conventions This product specification follows a set of typographic rules that make s the document consistent and easy
Product, Specification, Electronic, Product specification, Nrf24l01, Sparkfun, Sparkfun electronics
Single chip 2.4 GHz Transceiver nRF24L01
www.sparkfun.comPRELIMINARY PRODUCT SPECIFICATION nRF24L01 Single Chip 2.4 GHz Radio Transceiver Nordic Semiconductor ASA - Vestre Rosten 81, N-7075 Tiller, Norway - Phone +4772898900 - …
Product, Specification, Nrf24l01, Nrf24l01 product specification
XBee /XBee-PRO RF Modules - SparkFun Electronics
www.sparkfun.comThe XBee®/XBee-PRO® RF Module was designed to mount into a receptacle (socket) and there-fore does not require any soldering when mounting it to a board. The XBee Development Kits con-tain RS-232 and USB interface boards which use two 20-pin receptacles to receive modules.
GSM/GPRS Module - SparkFun Electronics
www.sparkfun.comThis document gives an overview of the LinkSprite GSM/GPRS module: a miniature, single-side board, quad-band GSM 850/EGSM 900/DCS 1800/PCS 1900 module, ready for integration in various kinds of Fix wireless phones and other wireless devices.
Electronic, Module, Gprs, Sparkfun, Sparkfun electronics, Gsm gprs module
16-Channel Constant-Current LED Driver
www.sparkfun.comA6282 Description The A6282 device is designed for LED display applications. This CMOS device includes an input shift register, accompanying data latches, and 16 MOS constant current sink drivers.
Constant, Drivers, Current, Constant current, Constant current led driver
+3.3V Low Power Half-Duplex RS-485 Transceivers with ...
www.sparkfun.com10/15/02 SP3481/3485 Low Power Half-Duplex RS485 Transceivers © Copyright 2000 Sipex Corporation 2 SPECIFICATIONS T AMB = T MIN to T MAX and V CC = +3.3V ± 5% ...
Power, Half, Duplex, 3v low power half duplex rs, Low power half duplex
Typical Application - sparkfun.com
www.sparkfun.comFully Integrated, Hall Effect-Based Linear Current Sensor with ACS712 2.1 kVRMS Voltage Isolation and a Low-Resistance Current Conductor Allegro MicroSystems, Inc. 3 115 Northeast Cutoff
Related documents
Introduction to Socket Programming
alumni.cs.ucr.eduSocket functions like connect(), accept(), and bind() require the use of specifically defined address structures to hold IP address information, port number, and protocol type. This can be one of the more confusing aspects of socket programming so it is necessary to clearly understand how to use the socket address structures.
Introduction, Programming, Sockets, Socket programming, Introduction to socket programming
Getting Started with C Programming for the ATMEL AVR ...
www.elec.uow.edu.au3. Using Atmel Studio for C programming 3 3.1 Creating an Atmel Studio project 3 3.2 Compiling C code to HEX file 5 3.3 Debugging C program using the simulator 6 3.4 Downloading and running HEX file on AVR board 8 1. Introduction This tutorial provides information on the tool and the basic steps for programming the Atmel
EtherNet/IP Web Server Module
literature.rockwellautomation.com11 Publication ENET-UM527E-EN-P - October 2006 Preface About This Publication Use this manual as a reference when installing, using, and troubleshooting your EtherNet/IP Web Server Module. This manual explains the use of the following EtherNet/IP Web Server
Network Programming - Simplify C++ Development
pocoproject.orgThe Socket Class > Poco::Net::Socket is the root class of the sockets inheritance tree. > It supports methods that can be used with some or all kinds of sockets, like: > select() and poll() > setting and getting various socket options (timeouts, buffer sizes, reuse address flag, etc.) > getting the socket's address and the peer's address
Altera DE0 Board - Intel
www.intel.com• USB Blaster (on board) for programming and user API control; both JTAG and Active Serial (AS) programming modes are supported • 8-Mbyte SDRAM • 4-Mbyte Flash memory • SD Card socket • 3 pushbutton switches • 10 toggle switches • 10 green user LEDs • …
WorkCentre 5325/5330/5335 Multifunction Printer
www.office.xerox.comWorkCentre® 5325/5330/5335 Detailed Specifications 3 Envelope Tray (Optional – replaces Tray 1) Capacity1 Up to 60 envelopes Sizes #10 Commercial (9.25 x 4.125 in.), Monarch, DL, C5 Custom sizes: 3.9 x 5.8 in. to 6.4 x 9.5 in. (98 x 148 mm to 162 x 241 mm)
Printer, 2535, Workcentre, Multifunction, 5330, 3355, Workcentre 5325 5330 5335 multifunction printer