Design Manual Clear Zones Chapter 8 Safety Design ...

1 Page 1 of 8 This section provides guidelines for determining Clear zone distances on primary highways. The location from which the Clear zone is measured ( edge of traveled way or back of curb ) and the appropriate procedures for determining the Clear zone width depend on the type of highway. Definition A Clear zone is defined as a roadside area that is free of objects, where an out-of-control vehicle can traverse safely. The width of a Clear zone is measured relative to the edge of traveled way. How far the Clear zone extends from this point can be expressed in two ways: Design Clear zone distance, or provided Clear zone distance. Design Clear Zone Distance This is the width of Clear zone that should be provided along a given roadway for a specific project. This distance is chosen from one of the Clear zone tables and is based on traffic speeds, traffic volumes, horizontal curvature, and roadside geometry. Design Clear zone distance can change along a project.

2 Such a change may result from a change in Design speed, traffic volumes, horizontal curvature, or roadside geometry. Provided Clear Zone Distance This is a measure of the actual Clear zone width that is available along a given roadway. This distance is measured from the edge of traveled way out to the face of the nearest object. The provided Clear zone distance should be equal to or greater than the Design Clear zone distance. Figure 1: Example of possible Clear zone distances at a given point along a roadway. While the Design Clear zone distance may remain constant along a segment of roadway, provided Clear zone distance distances may vary considerably. As seen in Figure 1, the provided Clear zone distance extends from the edge of traveled way out to the nearest hazard a large tree in this case. However, just upstream or downstream of this tree, the nearest hazard may be much farther from the roadway. Thus, the provided Clear zone distance at these locations may be significantly larger.

3 Figure 2 demonstrates Clear Zones 8A-2 Design Manual Chapter 8 Safety Design Originally Issued: 12-13-10 Revised: 11-12-20 Design Bureau Chapter 8 Safety Design Section 8A-2 Clear Zones Page 2 of 8 this possibility. The provided Clear zone distance is much larger just upstream and downstream of each object. Figure 2: Example of how Clear zone distances may vary along a roadway. Clear Zone Distances for Highways For freeways, expressways, rural two lane highways, and transitional facilities, select the Design Clear zone distance from the appropriate Clear zone table below. For low speed urban facilities, refer to the discussion near the end of this section. Preferred Clear Zone Table Acceptable Clear Zone Table Within the table, use bi-directional mainline traffic volumes (ADT) that would be expected in the Design year of the project. For ramps that are separate from the mainline, use the ramp volume. Ramp tapers and auxiliary lanes are special cases and are discussed later in this section.

4 Since traffic speeds, traffic volumes, horizontal curvature, and roadside geometry can all vary throughout a corridor, Clear zone distances must be determined for each distinct roadway segment. Right-of-way availability, environmental concerns, or economic factors may impact the ability to provide Clear Zones . Where Clear zone distances do not meet the requirements set forth in this Chapter , document this according to Section 1C-8. Slopes A vehicle leaving the roadway will normally encounter some type of slope either a foreslope or a backslope. A roadside cross section may contain multiple foreslopes, multiple backslopes, or combinations of both. The steepness of a roadside slope can affect a vehicle s stability and trajectory. It is one of the factors used in the determination of Clear zone widths. As used in this Manual , slopes are defined as a ratio of horizontal distance to vertical rise or fall. For example, a 4:1 foreslope is a slope that falls away one foot for every four feet.

5 Figure 3 illustrates this concept. Figure 3: A 4:1 foreslope. Foreslopes and backslopes that are too steep can be considered hazardous and, therefore, cannot be counted as part of a Clear zone. The following sections describe how foreslopes and backslopes are classified based on their steepness. Foreslopes A foreslope is a parallel slope that falls away from the roadway. Foreslopes are typically encountered where the roadway is higher than the surrounding natural ground line. Where a roadside ditch exists, a foreslope connects the edge of the shoulder to the bottom of the ditch. Foreslopes are identified as recoverable, non-recoverable, and critical. Each of these features is discussed below. Chapter 8 Safety Design Section 8A-2 Clear Zones Page 3 of 8 Recoverable A recoverable foreslope (4:1 or flatter) is a slope on which an errant motorist is likely to regain control. Recoverable foreslopes can be counted as part of a Clear zone and their use is preferred whenever possible (see Figure 4).

6 Figure 4: Example of a recoverable foreslope Design . Non-Recoverable A non-recoverable foreslope is a slope on which an errant motorist will unlikely be unable to stop and will continue on to the bottom of the slope. Non-recoverable foreslopes are those steeper than 4:1 to as steep as 3:1. Complete recovery usually will not occur until the vehicle travels a certain distance beyond the base of such a slope. Therefore, a recoverable area free of objects should be provided at the toe of a non-recoverable slope. Non-recoverable foreslopes cannot be counted as part of a Clear zone (see Figure 5). Figure 5: Example of a non-recoverable foreslope Design . Critical A critical foreslope (steeper than 3:1) is a slope on which most vehicles would be expected to roll over. Critical foreslopes should be evaluated for treatment (refer to Section 8A-4). Critical foreslopes cannot be counted as part of a Clear zone (see Figure 6). Chapter 8 Safety Design Section 8A-2 Clear Zones Page 4 of 8 Figure 6: Example of a critical foreslope Design .

7 Backslopes A backslope is a parallel slope that falls toward the roadway, and is typically encountered where the roadway is lower than the natural ground line. Where a roadside ditch exists, a backslope also connects the bottom of the ditch to the surrounding ground. The effects of backslopes on vehicle dynamics have not been studied as extensively as those of foreslopes. Therefore, the relative Safety effects of various backslope designs are not as well understood. Nevertheless, flatter backslopes are preferred whenever possible. Moderate A moderate backslope ( :1 or flatter) is a slope on which most vehicles should be able to traverse safely. Moderate backslopes are not considered hazardous. Severe A severe backslope (steeper than :1) is a slope on which some vehicles might be expected to roll over. Severe backslopes may be considered hazardous and should be evaluated for treatment (refer to Section 8A-4). Severe backslopes cannot be counted as part of a Clear zone.

8 Adjustment at Horizontal Curves The Design Clear zone distance should be adjusted at certain horizontal curves. Adjust the width of the Clear zone at a curve when a crash history or engineering judgment suggests the need for additional width. Otherwise, adjust the width when all of the following criteria are met: The Design speed of the roadway is 55 mph or greater. The radius of the curve is 2860 feet or less. The curve occurs on a normally tangent alignment (one where the curve is preceded by a tangent more than one mile in length). Use the following equation to determine the adjusted Clear zone distance when widening at horizontal curves: CZC = CZT KCZ where: CZC = adjusted Design Clear zone distance at curve (rounded to nearest foot) CZT = Design Clear zone distance on tangent segment KCZ = curve adjustment factor Chapter 8 Safety Design Section 8A-2 Clear Zones Page 5 of 8 Table 1: KCZ (Curve Adjustment Factors) radius (ft.) Design speed (mph) 40 45 50 55 60 65 70 2860 2290 1910 1640 1430 1270 1150 950 820 720 640 570 380 As Figure 7 shows, the Clear zone should be adjusted only on the outside of the first curve following the tangent.

9 If the alignment is generally curvilinear, no adjustment factor should be applied. Similarly, if the alignment is curvilinear preceding the curve in question, then no adjustment factor should be applied. Figure 7: Clear zone adjustment at horizontal curves. Chapter 8 Safety Design Section 8A-2 Clear Zones Page 6 of 8 Figure 8 shows the appropriate method for initiating and terminating an adjusted Clear zone width at horizontal curves. Figure 8: Initiating and terminating adjusted Clear zone width at curves. Ramp Tapers and Auxiliary Lanes Determining Clear zone distances for ramp tapers, auxiliary lanes, climbing lanes, or turning lanes involves a three step process: Determine the Clear zone distance from the edge of the through lane based on through lane traffic volume and speed. Determine the Clear zone distance from the edge of the auxiliary lane based on auxiliary lane traffic volume and speed. Compare the calculated distances. The distance which extends to a point further from the edge of the auxiliary lane is used as the overall Clear zone distance for this location.

10 Refer to Figure 9 for an example. Figure 9: Example of a Clear zone calculation for auxiliary lanes. For the example shown in Figure 9, the Clear zone distance for the through lanes would be the controlling Clear zone for this road segment. Chapter 8 Safety Design Section 8A-2 Clear Zones Page 7 of 8 Clear Zone Distances for Transitional and Low Speed Urban Facilities Transitional and urban roadway environments present unique sets of circumstances, often with conflicting interests sharing limited right-of-way. For transitional facilities, speed limits are typically between 35 and 45 mph, gutter sections are being introduced, and right-of-way is being reduced. With low speed urban facilities, on-street parking is common, and bicyclists and pedestrians may be present. For both types of facilities, trees, light poles, traffic signals, and other roadside objects tend to be located near the traveled portion of the roadway. Lateral Offset Lateral offset to all obstructions including crashworthy devices must be provided.