Manufacturing Company, Inc. - energymfg.com

1 Inch ( cm) to Inch ( cm) Bores; Up to Foot ( m) Stroke LengthsCHD SERIES HEAVY DUTYCUSTOM WELDED HYDRAULIC CYLINDERSENERGY Manufacturing company , CYLINDER DESIGNEnErgy Manufacturing company , : 319-465-3537 Fax 319-465-5279 Email: CYLINDER DIMENSIONSBore Diameter Available Rod Diameters1 ( cm) .5 ( cm), .625 ( cm), .75 ( cm) ( cm) .75 ( cm), 1 ( cm), ( cm) ( cm) 1 ( cm), ( cm)2 ( cm) 1 ( cm), ( cm), ( cm), ( cm) ( cm) ( cm), ( cm) ( cm) ( cm), ( cm), ( cm), ( cm), ( cm), ( cm), 2 ( cm) ( cm) ( cm), ( cm), ( cm), 2 ( cm)3 ( cm) ( cm), ( cm), ( cm), ( cm), 2 ( cm), ( cm), ( cm) ( cm) ( cm) ( cm) ( cm), ( cm), ( cm), 2 ( cm), ( cm), ( cm), ( cm), 3 ( cm) ( cm) ( cm)4 ( cm) ( cm), ( cm), ( cm), 2 ( cm), ( cm), ( cm), 3 ( cm) ( cm) ( cm), 2 ( cm) ( cm) ( ), ( cm), 2 ( cm), ( cm), ( cm), ( cm), 3 ( cm), ( cm) ( cm) ( cm)5 ( cm) 2 ( cm), ( cm), ( cm), ( cm), 3 ( cm), ( cm), ( cm), 4 ( cm) ( cm) ( cm)

2 , ( cm) ( cm) ( cm), ( cm), ( cm), ( cm) ( cm) ( cm)6 ( cm) ( cm), ( cm), 3 ( cm), ( cm), 4 ( cm), ( cm) ( cm) ( cm), 5 ( cm)7 ( cm) ( cm), 3 ( cm), 4 ( cm), 5 ( cm) ( cm) 4 ( cm)8 ( cm) ( cm), 6 ( cm)9 ( cm) 6 ( cm)10 ( cm) Please consult factoryPlease consult factory if the bore / rod combination you desire is not shown above A variety of seal packages to fit most applications St DOM steel tubing skive-burnished to 4 10 micro-inches, RMS (.1 to .25 microns, RMS) Standard rod seal is an energized twin-lip u-cup with backup ring Ground and polished 1045 steel rod hard chrome plated to a minimum of .0005 ( microns) Ductile iron or steel piston and guide Glass-filled nylon wear rings available as neededCHD DESIgN OpTIONS & SpECIAL pORT bLOCkSIllustration is one typical example.

3 For other options consult VALVE bLOCk (bOLTED ON)SpECIAL VALVE bLOCk IN bASE ENDENERgY Manufacturing CUSTOMWELDED CYLINDER ExAMpLESADDITIONALAVAILAbLEfEATURES: Single-acting cylinders Ram-type cylinders Custom end mechanisms Custom fluid lines Hydraulic cushioning Integral stop tubes Custom valve blocks and valves Position sensing cylinders Re-phasing cylinderspORT OpTIONS AVAILAbLE Standard SAE O-Ring Ports: Available in straight, 90 elbow, and several other configurations NPTF Ports: Available in straight, 90 elbow, and several other configurations 4-Bolt Flange Ports: Please consult factory for availabilityIllustration is one typical example. For other options consult Manufacturing company , Plastic Lane Monticello, IA 52310-9472 USAP hone: (319) 465-3537 Fax: (319) 465-5279 Web Site: E-mail: 2003 energy Manufacturing company , Inc.

4 Form No. CSR-7 ISO 9001 energy Mfg. Co., energy welded cylinders are complete and return the following sheet so that we can provide you with the best cylinder for your application. Custom Quotation Request FormThis form must be filled out in its entirety before a welded cylinder quotation can be prepared. Unless noted otherwise by the customer, energy Manufacturing will use the following parameters with respect to the processing of this request:1. The oil temperature in the cylinder will be 170 Fahrenheit (77 Celsius) or The rod speed will be 50 feet per minute ( meters per minute) or System filtration will be 20 micron or The fluid used is SAE 20 (ISO VG68) or less-viscous petroleum-based fluid and is non-foaming type for hydraulic Mount center-to-center and stroke dimensions are +/- 1/8 (+ mm).

5 6. The cylinder is not used in a corrosive OF QUOTE:_____QUOTE DEADLINE DATE:_____CUSTOMER DATAC ustomer name: _____Address: _____City, State or Province, Zip or Postal Code: _____Telephone number: _____ Purchasing contact: _____Fax number: _____ Engineering contact: _____E-mail: _____CYLINDER DATAAll welded cylinder quotation requests should be accompanied by a blueprint or sketch and the following data should be cylinder requests must include pump flow to cylinder, weight of load, and details of the linkage between cylinder and size: _____Mountings:Stroke length: _____Base: _____Rod diameter: _____Rod: _____Retracted pin center length: _____Finish:Port type (pipe or SAE o-ring): _____Acrylic Water-BasedPort size: _____Primer Paint (please specify color): _____Mounting pin diameter: _____Other Paint (please specify): _____Test requirements: ( ) Standard 100% air test ( ) 100% Hydraulic testClear Rust-Preventative Coating: _____None: _____QUOTATION DATAA nnual Usage: _____ Release Quantity: _____Target Price: _____ Customer Part Number: _____APPLICATION DATAType of machine (crane, combine, etc.)

6 :_____ Primary cylinder effort will be to ( ) push load_____ ( ) pull load ( ) both push and pull loadWill cylinder be used to lift people?_____ Cylinder is ( ) double acting ( ) single actingType of function (hoist, swing, steering, etc.):_____ Cylinder is mounted ( ) vertically ( ) horizontally_____ ( ) swings through arc with mechanismEstimated cycles per year: _____Does cylinder always reach full extend or retractPressure values:position? _____ Operating: _____Is cylinder subjected to high overrunning loads? _____ Peak (if known): _____Is cylinder subjected to side loading? _____ Main system relief: _____Is cylinder barrel braced to restrict buckling? _____ Operating flow range: _____S003 7/03 RCUSTOM QUOTATION REQUESTM anufacturing company , Inc. 2011 energy Manufacturing company , Inc. Form CHD (Rev.)

7 7/2011)ISO 9001:2008 ENERGYM anufacturing company , Inc. Mfg. Co., Manufacturing company , Plastic Lane Monticello, IA 52310-9472 USAP hone: 319-465-3537 Fax 319-465-5279 Website: Email.