Green Thick Film Chip Resistors - Vishay …

1 RCG Draloric Revision: 01-Sep-141 Document Number: 20047 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT Thick Film Chip ResistorsFEATURES Green resistor - does not use RoHS exemptions Stability R/R = 1 % for 1000 h at 70 C 2 mm pitch packaging option for 0603 size Material categorization: for definitions of compliance please see Notes These Resistors do not feature a limited lifetime when operated within the permissible limits. However, resistance value drift increasing over operating time may result in exceeding a limit acceptable to the specific application, thereby establishing a functional lifetime.

2 Marking: See datasheet Surface Mount Resistor Marking (document number 20020). Power rating depends on the max. temperature at the solder point, the component placement density and the substrate (1)The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat flow support of the printed-circuit board (thermal resistance). The rated dissipation applies only if the permitted film temperature of 155 C is not ELECTRICAL SPECIFICATIONSTYPECASESIZEIMPERIALCASESI ZEMETRICPOWER RATINGP70 ppm/KTOLERANCE %RESISTANCERANGE , 1150 to 10ME24; to to 10ME24 Zero-Ohm-Resistor: Rmax. = 20 m , Imax.

3 = , to 10ME24; E962005E24 Zero-Ohm-Resistor: Rmax. = 20 m , Imax. = , to 10ME24; E962005E24 Zero-Ohm-Resistor: Rmax. = 20 m , Imax. = , to 10ME24; E962005E24 Zero-Ohm-Resistor: Rmax. = 20 m , Imax. = ATECHNICAL SPECIFICATIONSPARAMETERUNITRCG0402 RCG0603 RCG0805 RCG1206 Rated dissipation P70 (1) voltage Umax. ACRMS/DCV5075150200 Insulation voltage Uins (1 min)V75100200300 Insulation resistance > 109 Operating temperature range C- 55 to + Draloric Revision: 01-Sep-142 Document Number: 20047 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT NUMBER AND PRODUCT DESCRIPTIONPART NUMBER: RCG080510K0 FKEATYPEVALUETOLERANCETCRPACKAGINGRCG040 2 RCG0603 RCG0805 RCG1206R = DecimalK = ThousandM = Million0000 = 0 JumperD = %F = %J = %Z = JumperK = 100 ppm/KL = 150 ppm/KN = 200 ppm/K0 = JumperEA, EB,EC, ED,EE, EI,ELPRODUCT DESCRIPTION.

4 RCG0805 100 10K 1 % EARCG080510010K1 %EATYPETCRRESISTANCE VALUE TOLERANCE PACKAGINGRCG0402 RCG0603 RCG0805 RCG1206 100 ppm/K 150 ppm/K 200 ppm/K10R = 10 10K = 10 k 1M = 1 M 0R0 = Jumper % 1 % 5 %EA, EB,EC, ED,EE, EI,ELPACKAGINGTYPECODEQUANTITYCARRIER TAPEWIDTHPITCHREEL DIAMETERRCG0402ED10 000 Paper tape IEC 60286-3 Type 1a8 mm 2 mm 180 mm/7"EE50 000330 mm/13"RCG0603EI5000 Paper tape IEC 60268-3 Type 1a8 mm 2 mm 180 mm/7"ED10 000180 mm/7"EL20 000285 "EE50 000330 mm/13"EA5000 Paper tape IEC 60268-3 Type 1a8 mm 4 mm 180 mm/7"EB10 000285 "EC20 000330 mm/13"RCG0805EA5000 Paper tape IEC 60268-3 Type 1a8 mm 4 mm 180 mm/7"EB10 000285 "EC20 000330 mm/13"RCG1206EA5000 Paper tape IEC 60268-3 Type 1a8 mm 4 mm 180 mm/7"EB10 000285 "EC20 000330 mm/13"RCG080510K0 FKEARCG Draloric Revision: 01-Sep-143 Document Number: 20047 For technical questions, contact.

5 DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT PERFORMANCEN otes No exemptions ( Pb in glass) may be applied to any substances or application for the Green category All concentration levels are based on homogenous materialsDIMENSIONS in millimetersSIZEDIMENSIONSSOLDER PAD DIMENSIONSREFLOW SOLDERINGWAVE SOLDERINGIMPERIAL METRICLWHT1T2ablabl0402RR1005M + + + - + REQUIREMENTSSUBSTANCESCONCENTRATION LIMITLead (Pb)< 1000 ppmMercury (Hg)< 1000 ppmCadmium (Cd)

6 < 100 ppmHexavalent Chronium< 1000 ppmPolybrominated Biphenyl (PBB)< 1000 ppmPolybrominated Diphenyl Ether (PBDE)< 1000 ppmBromine (Br)< 900 ppmChlorine (Cl)< 900 ppmSum of Bromine and Chlorine 1500 ppm (Sb)< 900 ppmRed Phosphorous< 100 ppmDeratingAmbient Temperature in ambFraction of Rated Dissipation P70- 5005010015005010070 C%RCG Draloric Revision: 01-Sep-144 Document Number: 20047 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT PROCEDURES AND REQUIREMENTSEN 60115-1 CLAUSEIEC 60068-2 TEST METHODTESTPROCEDUREREQUIREMENTSPERMISSIBLE CHANGE ( R)Stability for product types:STABILITY CLASS 1OR BETTERSTABILITY CLASS 2OR BETTERRCG e3 1 to 10 M 1 to 10 M %, 1 % 5 % proofU = x Uins; 60 sNo flashover or time overloadU = x 2 x Umax.

7 ;Duration acc. to style ( % R + ) ( % R + ) (Td)SolderabilitySolder bath method; flux;(245 5) C(3 ) sGood tinning ( 95 % covered)no visible (20/- 55/20) C and (20/125/20) C 100 ppm/K, 150 ppm/K 200 (Uu3)Shear(adhesion)RR 1608 and smaller: 9 NRR 2012 and larger: 45 NNo visible (Uu1)Substrate bendingDepth 2 mm;3 timesNo visible damage, no open circuit in bent position ( % R + ) ( % R + ) sequence:- (1 % R + ) (2 % R + ) (Ba)Dry heat125 C; 16 h (Db)Damp heat, cyclic55 C; 90 % RH; 24 h; 1 (Aa)Cold- 55 C; 2 (M)Low air pressure1 kPa; (25 10) C; 1 (Db)Damp heat, cyclic55 C; 90 % RH; 24 h; 5 loadU = at 70 CU = Umax.

8 ; h on; h off;70 C; 1000 h (1 % R + ) (2 % R + ) (Td)Resistance tosoldering heatSolder bath method(260 5) C;(10 1) s ( % R + ) ( % R + ) ,needle flame testIEC 60695-11-5;10 sNo burning after 30 (Cab)Damp heat,steady state(40 2) C;(93 3) % RH;56 days (1 % R + ) (1 % R + ) atupper categorytemperature155 C, 1000 h (1 % R + ) (2 % R + ) discharge (human body model) IEC 61340-3-1;3 pos. + 3 neg. discharges;ESD test voltage acc. to size (1 % R + )P70 x RP70 x RP70 x RRCG Draloric Revision: 01-Sep-145 Document Number: 20047 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE.

9 THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT tests are carried out in accordance with the following specifications: EN 60115-1, generic specification EN 140400, sectional specification EN 140401-802, detail specification IEC 60068-2, environmental test proceduresPackaging of components is done in paper tapes according to IEC (XA)Component solvent resistanceIsopropyl alcohol;50 C; method 2No visible (XA)Solvent resistance of markingIsopropyl alcohol;50 C; method 1, toothbrushMarking legible,no visible (Fc)Vibration, endurance by sweepingf = 10 Hz to 2000 Hz;x, y, z mm;A 200 m/s2;10 sweeps per axis ( % R + ) ( % R + ) electric overloadU = 2 x Umax.

10 ; s on; s off;1000 cycles (1 % R + ) pulse high voltage overload,10 s/700 s = 10 x 2 x Umax.;10 pulses (1 % R + )TEST PROCEDURES AND REQUIREMENTSEN 60115-1 CLAUSEIEC 60068-2 TEST METHODTESTPROCEDUREREQUIREMENTSPERMISSIB LE CHANGE ( R)Stability for product types:STABILITY CLASS 1OR BETTERSTABILITY CLASS 2OR BETTERRCG e3 1 to 10 M 1 to 10 M 15 x P70 x RP70 x R Legal Disclaimer Revision: 01-Jan-20191 Document Number: 91000 Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, Vishay ), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product.