Screwpump Series - klfpump.com

1 1 ACD 1116 GBOctober 2000 IMO AB, Telephone: + 46 8 50 622 800, Telefax: + 46 8 645 15 09E-mail: volume: 11-45 l/minMax differential pressure: 7 barApplications: Lubrication, circulation and transferScrewpump Series ACDP roduct description2 ACD 1116 GBOctober 2000 IMO AB, Telephone: + 46 8 50 622 800, Telefax: + 46 8 645 15 09E-mail: ACD pumps are used for a number ofdifferent fluids:Lubrication oil, fuel oil, vegetable oil,hydraulic oil and other hydraulic fluids,glycols, polymers, emulsions, and any non-aggressive fluid with some application are: Lubrication of diesel engines, gears, gasand steam turbines, hydro turbines, papermachines.

2 Circulation for cooling and filtration inlarge machineries and hydraulic systems,pumping transformer oil for insulation intransformers. Transfer onboard ships, in oil factories,refineries, tank farms dataInlet pressureMax. inlet pressure is 7 barMin. inlet pressure is shown in theSelection guideDisplacement cm3/rSize,lead 025L 025 NDisplacement cm3/r relief valveThe pump is equipped with an integralpressure relief valve with internal return,limiting the differential pressure across thepump and protecting the pump should thedischarge line be blocked.

3 The valve isadjustable for different opening value of the pressure limit can be set atthe factory and should be adjusted atinstallation (see Installation & Startupinstruction for Low pressure pumps ). Thevalve has a pressure accumulation of bar, so with moderate demands onpressure modulation, it may also be usedfor pressure regulation. The valve has amax. set pressure of 7 pump is designed to be short coupled toan electrical motor IEC size 71. The motorbearing will have to carry a slight axial loadfrom the rotor set. With motors deliveredfrom IMO AB, this load will not significantlyimpair the bearing life speed limitThe maximum speed is 3600 rpm.

4 Forhigher speeds contact IMO ACD pump is designed to operate inone rotational direction only, as standardclockwise when facing the shaft viscosity2-1500 mm2/s. For higher viscosities contactIMO temperature-20 C to 90 C for all types of levelA typical sound level from a pump withstandard driver is 58 dB(A). This value refersto free field conditions at 5 bar, 2940 rpm and40 cSt, measured according to ISO and recommendationVersion NTBP is recommended wheneverthe starting viscosity might exceed 800 otherwise specified, version IVBP will be pressureMaximum differential pressure is 7 bar but is reduced at low viscosities as shown in thetable , mm2/s (cSt)2345678910 Max.

5 Diff. pressure (bar) 4,2 4,7 5,1 5,5 5,86,06,36,56,7 Discharge pressureMaximum discharge pressure is 12 bar3 ACD 1116 GBOctober 2000 IMO AB, Telephone: + 46 8 50 622 800, Telefax: + 46 8 645 15 09E-mail: and designIVBPNTBPPump bodyPearlitic cast ironNodular cast ironPower rotorSteel, surface treatedSteel, surface treatedIdler rotorsPearlitic cast iron,Pearlitic cast iron, surface treatedsurface treatedShaft sealCarbon/Ni-resistCarbide/CarbideViton elastomersViton elastomersUnitsThe following units are frequently used for specification of pumps .

6 SI-unitIMO unitsUSA unitsconversionPressurePa (MPa)barpsi1 bar = 14,5 psi = 0,1 MPaSpeedr/srpmrpm1 rpm = 0,016667 r/sViscositymm2/scStSSUsee tableTemperature C C F C = ( F-32)/1,8 Lengthmmminch1 mm = 0,0394 inchFlow ratem3/slit/minGPM1 lit/min = 0,264 GPMPump model codePump seriesACDSize(Power rotor diameter, mm)LeadL=Low leadN=Normal leadGenerationDesign generation 6 Material in pump bodyI=Perlitic cast ironN=Nodular cast ironShaft seal designV=Carbon/Ni-resist. elastomers in VitonT=Carbide/Carbide, elastomers in VitonMountingB=Flange mountingValveP=Pressure relief valve includedSpecial designCode group omitted for standard designViscosity tablecSt2482037752004008001500 SSU 32,6 39,2 52,2 99,4 174 346 927 1850 3700 69404 ACD 1116 GBOctober 2000 IMO AB, Telephone: + 46 8 50 622 800, Telefax: + 46 8 645 15 09E-mail: Speed: 1450 rpm Speed: 2900 rpm&Diff.

7 Pressure (bar)Diff. pressure (bar)Lead(cSt) Speed: 1750 rpm Speed: 3500 rpm&Diff. pressure (bar)Diff. pressure (bar)Lead(cSt) guide 50 HzSelection guide 60 Hz(lit/min)(kW)(lit/min)(kW) (bar)* (bar)* (bar)* (bar)* * Valid for liquids free from unresolved air or gas. * Valid for liquids free from unresolved air or 1116 GBOctober 2000 IMO AB, Telephone: + 46 8 50 622 800, Telefax: + 46 8 645 15 09E-mail: dimensionsPump ACDD imensions in mm (The counter flanges are accessories)Pump unit ACDD imensions in mm (With standard electric motor)Fig.

8 1 Fig. 26 ACD 1116 GBOctober 2000 IMO AB, Telephone: + 46 8 50 622 800, Telefax: + 46 8 645 15 09E-mail: Fig. 3 Bare shaft pumpFig. 4 Set of counter flangesFig. 5 Angle bracketFig. 7 Electric motorFig. 6 Double assembly unitA bare shaft pump (fig. 3) can be ordered with the accessories in fig. 4 ACD-pump with counter flanges of theweld neck type is mounted directly to anelectric motor and has an angle bracket formounting horizontally, vertically or anyother attitude. Two pump units can also bemounted to a double assembly on a com-mon frame with inlet and outlet pipeconnections.

9 The double assembly savesspace and facilitates installation,maintenance, service and supervision. SeeProduct Description for T4. For more information about installationread the Installation and Start-up manualfor low pressure and ServiceSpare parts for these pumps are easilyavailable from stock. For detailed informa-tion and know-how about service read theMaintenance and Service instruction forACD- pumps or contact IMO 1116 GBOctober 2000 IMO AB, Telephone: + 46 8 50 622 800, Telefax: + 46 8 645 15 09E-mail: view flow outflow in601551451 443 509 1020 614 615 605 602 ACD 025, all modelsList of componentsPos No Denomination1020 Power rotor134 Locking screw162 Nylon sleeve socket202 Idler rotor401 Pump body443 Drip nipple451 Screw501 Front cover506O-ring509 Shaft sealPos No Denomination551 Rear cover556 Gasket601 Valve cover602 Sealing washer605O-ring612 Regulating screw612 ARetaining ring614 Valve piston615 Valve spring501162451134506556202401612A612 Fig.

10 88 ACD 1116 GBOctober 2000 IMO AB, Telephone: + 46 8 50 622 800, Telefax: + 46 8 645 15 09E-mail: AB: Box 42090, S-126 14 STOCKHOLM, Sweden. Telephone: + 46 8 50 622 800 Telex: 11548 IMO S, Telefax: + 46 8 645 15 09, E-mail.