Precision Low TCR High Temperature Thin Film …

1 Dale thin film Revision: 08-Jul-161 Document Number: 60082 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT Low TCR high Temperature thin film Resistor,Surface Mount Chip, 5 ppm/ C TCR, % ToleranceVishay s proven Precision thin film wraparound resistors will meet your exact requirements. These resistors are ideal for use in oil industry Precision applications requiring low noise, long term stability under high Temperature , ultra low Temperature coefficient of resistance, and low voltage coefficient. The chip resistors are available in any resistance ohmic value in the range specified PLTT0603 case size is qualified to AEC-Q200 for automotive applications -55 C to 215 C operating Temperature range TCR of 5 ppm/ C standard Tolerances to % Anti corrosion resistant film with (SPM) special passivation method Stable film and performance characteristics % max.

2 At 2000 h, 215 C, 25 % rated power Non-standard resistance values available Very low noise and voltage coefficient (< -30 dB, ppm/V) UL 94 V-0 flame resistant Gold terminations (10 " to 20 ") Material categorization: for definitions of compliance please see TYPICAL PERFORMANCENote Consult factory for additional case sizeAdhesion LayerHigh PurityAlumina SubstrateNickel BarrierPlatedGold (10 " to 20 ")SPM PassivationEnhancementPassivated NichromeResistive ELECTRICAL SPECIFICATIONSTESTSPECIFICATIONSCONDITIO NSM aterialPassivated nichrome-Resistance Range50 to 3 M -TCR: Absolute 5 ppm/ C-55 C to +215 CTolerance: Absolute % to %+25 CStability: Absolute R %2000 h at 215 C, 25 % rated powerStability: Ratio--Voltage Coefficient ppm/V (typical)-Working Voltage100 V to 200 V-Operating Temperature Range-55 C to +215 C-Storage Temperature Range-55 C to +215 C-Noise< - 35 dB (typical)-Shelf Life Stability: Absolute R %1 year at +25 CCOMPONENT RATINGSCASE SIZEPOWER RATINGAT 70 C(mW)WORKING VOLTAGE(V)RESISTANCE RANGE ( )06031507575 to 130K0805250100250 to 260K1206400200500 to 775K2010800200500 to 2M25121000200500 to Dale thin film Revision: 08-Jul-162 Document Number: 60082 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE.

3 THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT in inchesCASE to to to + + to to TESTS - MIL-PRF-55342 ENVIRONMENTAL TESTCONDITIONSTYPICAL vishay PERFORMANCET hermal ShockMIL-STD-202 method 107 Cond F, -65 C to +150 C %Short Time OverloadMIL-PRF-55342 Para , rated working voltage %Low Temperature OperationMIL-PRF-55342 Para , -65 C %Resistance to Soldering HeatMIL-STD-202 method 210 %Moisture ResistanceMIL-STD-202 method 106, no power applied % high Temperature ExposureMIL-PRF-55342 Para , at 150 C for 100 h %LifeMIL-STD-202 method 108, 25 % rated powerfor 2000 h at 215 C %TCRMIL-STD-202 method 304 5 ppm/ CENVIRONMENTAL TESTS - AEC-Q200 PLTT0603 Case Size OnlyENVIRONMENTAL TESTCONDITIONSTYPICAL vishay PERFORMANCEHigh Temperature storageMIL-STD-202 method 108, 1000 h at 125 C % Temperature cyclingJESD22 method JA-104, 1000 cycles,-55 C to +155 C %Moisture resistanceMIL-STD-202 method 106, no power applied %Biased humidityMIL-STD-202 method 103, 1000 h at 85 C,85 % RH, 10 % rated power %LifeMIL-STD-202 method 108,1000 h at 175 C, 50 % rated power %Mechanical shockMIL-STD-202 method 213, condition C %VibrationMIL-STD-202 method 204, 10 Hz to 2 kHz %Resistance to soldering heatMIL-STD-202 method 210, condition B %Electrostatic dischargeAEC-Q200-002, human body (< 1 k : 1 kV; > 1 k : 2 kV)< 1 k : 1 kV.

4 > 1 k : 2 kVSolderabilityMIL-STD-883 method 2003 para and J-STD-002 PassTCRMIL-STD-202 method 304 5 ppm / CDie shearMIL-PRF-55342, kg for 30 s minimunPassFlame retardanceAEC-Q200-001 para Dale thin film Revision: 08-Jul-163 Document Number: 60082 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT Performance obtained with following mounting conditions PCB: Polymide IPC-7831A STD land patterns Solder paste: PbSnAg ( )Note(1)Q tolerances are available only for resistance values 250 .DERATING CURVEA mbient Temperature C070215230 Percent of Rated Power0255075100175 PLTT0805 500 STABILITY TEST RESULTSTime on Test (h)Maximum (%)- Conditions:Case Size: 0805 Resistance Value: 500 Applied Power: 25 % of rated powerTest Chamber Temperature : 215 CPLTT0805 50 k STABILITY TEST RESULTSTime on Test (h)Maximum (%)- Conditions:Case Size: 0805 Resistance Value: 50 k Applied Power: 25 % of rated powerTest Chamber Temperature : 215 CGLOBAL PART NUMBER INFORMATIONGLOBALMODELCASESIZETCRCHARACT ERISTICRESISTANCETOLERANCETERMINATIONPAC KAGINGPLTT06030805120620102512Z = 5 ppm/ CThe first 3 digits are significant figures and the last digit specifies the number of zeros to follow.

5 R designates the decimal point. Example: 1001 = 1 k 2500 = 250 Special values with more than 4 significant figures, use a R for value below 1 k and a K for values greater than 1 k to signify a decimal point. 982R6 = 532R41 = Q = % (1)A = %B = %D = %F = 1 %G = 2 %G = Wraparound Gold over Ni barrier (10 " min. Au)WS = WAFFLE WI = 100 (item single lot date code) WP = 100 (package unit single lot date code) TAPE AND REEL T0 = 100 min., 100 mult T1 = 1000 min., 1000 mult T5 = 500 min., 500 mult TF = Full reel TS = 100 min., 1 mult TI = 100 (item single lot date code) TP = 100 min., 1 mult (package unit single lot date code)05Z101Q00GT1 TPL8 TLegal Disclaimer Revision: 08-Feb-171 Document Number: 91000 Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.

6 vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, vishay ), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability.

7 Statements regarding the suitability of products for certain types of applications are based on vishay s knowledge of typical requirements that are often placed on vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer s technical experts. Product specifications do not expand or otherwise modify vishay s terms and conditions of purchase, including but not limited to the warranty expressed as expressly indicated in writing, vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the vishay product could result in personal injury or death.

8 Customers using or selling vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized vishay personnel to obtain written terms and conditions regarding products designed for such license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of vishay . Product names and markings noted herein may be trademarks of their respective owners. 2017 vishay INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED