Crude Oil and E&P Testing - Stanhope-Seta

1 Crude Oil and E&P TestingLaboratory Instruments for quality control, analysis and calibrationStanhope-Seta, London Street, Chertsey, Surrey, KT16 8AP, UK t: +44 (0) 1932 564391 | e: | Part No: SA4000-3 VPP Part No: SA4015-0 Crude Oil Test Kit:SA4021-0H2S Analyser range: 0-250 mg/kg in the liquid phase (0-250 ppm H2S)Viscosity Range: Up to 3000 mm2/sPrinciple of measurement: Advanced Electrochemical sensorTest duration: 25 minutes with VPPS ample size: 1ml, 2ml, 5ml (depending on H2S concentration)Diluent volume: 20mlSize (HxWxD) /Weight:H2S Analyser: 21 x 30 x 41 cm / 8kgVPP: 40 x 24 x 20 cm / Analyser with Vapour Phase Processor (VPP)TM (SA4000-3 & SA4015-0)ASTM D7621 Appendix X1; IP 570 Procedure A Measurement range from 0-250 mg/kg H2S (0-250 ppm H2S) in the liquid phase Vapour Phase Processor proven to eliminate effects of chemical interference A non chemical method, no wet chemistry involved Small lab bench footprint, fully portable operation Suitable for monitoring Crude oils in the distribution system Critical Measurement method for Product Safety and ReleaseThe H2S Analyser was developed with Lloyd s Register s Fuel Oil and Bunker Analysis Service (FOBAS) along with support of other major international oil companies to offer rapid measurement of H2S in petroleum products.

2 The VPP accessory was subsequently developed to eliminate the effects of chemical interference and to enable the analyser to address a broader range of petroleum products. The Crude Oil Test Kit (SA4021-0) allows the H2S Analyser to be used for Testing Crudes and provides a highly cost effective test giving repeatable results even at low gas H2S Analyser is an excellent tool for supporting product Quality Control and safety ensuring product is within approved specification. It is also ideal for both product remediation treatment of feedstock components and off-spec products with fast repeat sample measurement is efficiently purged from the test sample by a combination of heat and agitation, and is measured by an advanced electrochemical sensor. The instrument offers a cost effective solution for H2S measurement no costly chemicals are required and there is no need for analytical preparation by an expert chemist.

3 View a demo video at: SA4000-3 & SA4015-0 Stanhope-Seta , London Street, Chertsey, Surrey, KT16 8AP, UK t: +44 (0) 1932 564391 | e: | Oil and E&P Testing2 Crude Oil Test Kit (SA4021-0)The Crude Oil kit allows the H2S Analyser to be used with the Vapour Phase Processor for Testing Crudes in accordance with Appendix X1 of ASTM D7621. New Test Vessel Crude Oil Test KitIP 570 Proficiency Test Scheme (PTS)IP 570/14a Mandated Verification ProcedurePTS is an invaluable Quality Assurance tool allowing participants to: Evaluate and monitor laboratory and instrument performance Provide additional confidence by demonstrating compliance with laboratory accreditation requirements Identify inter-laboratory differences by the comparison of test results and calculated statistical parameters with other laboratories in accordance with ISO/IEC 17025 Identify problems such as inadequate test or measurement processes and procedures Identify problems with the calibration of laboratory test equipmentVisit: SA4032-0 IP 570 PTS PackSeta Part No:4 place: 90000-3 or 6 place: 90100-0 Maximum RCF.

4 2214gMaximum RPM: 3000 Temperature Range: 30 to 80 C ( 1 C)Timer Range: 1 to 60 minutes in 1 minute steps, Continuous OperationRotor Capacity: 4 or 6 place samplesPower Requirement: 230 Vac (110V transformer option) 50/60Hz / 1kWSize (HxWxD) / Weight: 40 x 56 x 64cm / 86kgSeta Oil Test Centrifuge for Sediment & Water ASTM D4007; D96 (Obs); D1796; D2709; ISO 9030 Specifically designed for Testing oils Heated chamber, ambient to 80 C Static, near vertical bucket positioning 4 or 6 place swing out rotor Membrane touch control panel Pre-heat facility to ensure bowl is at test temperature prior to test Conforms to IEC 1010-1 & 1010-2-D safety requirementsThe Centrifuge has a large diameter chamber, with four or six place rotor and cushioned adaptors, which allows the use of 6 and 8 inch conical, pear-shaped, trace sediment and tubes.

5 The swing out rotor ensures that the samples are held near vertical when at rest allowing more precise measurement of sediment. An optional hazard reduction system extracts vapours and gases released from volatile Centrifuge (90000-3): place Centrifuge (90100-0): Tubes 100ml Long & Short Cone, Trace Sediment, and Finger Tubes Manufactured in strict compliance to test methods Permanently etched graduations High visibility white lined markings Optional factory certified, 7 point, long cone tubesSalt Content in Crude Analyser (99700-5)ASTM D3230; IP 265 Automatic salt concentration calculation Pre-calibrated for immediate use Membrane touch screen Interchangeable sensor 3 operating modes (ASTM, IP, user defined) Verification mode Battery or mains voltage operation MoistureproofA portable instrument for determining the approximate chloride (salts) content of Crude oils.

6 The instrument is pre-calibrated and automatically calculates the salt concentration in g/m3 or pounds per thousand barrels (ptb) (lb/1000bbl). Measurements can be displayed or downloaded to a PC. The instrument is supplied with carry case, mains adaptor, software, RS232 cable and instruction manual. An optional bench stand is available as an accessory (99701-0).Visit: - Salt in Crude Analyser Verification Tool (99703-0)A set of 3 SaltCheck verification modules which are calibrated to show equivalent salt values of 0 g/m3, 30 g/m3 and 190 g/m3. Instrument verification is easy - simply switch the instrument on and place the sensor into each SaltCheck module to confirm that the correct reading is being displayed. Saltcheck is supplied in a convenient storage case with a certificate of : Part No:99700-5 Salt in Crude Analyser99703-0 Verification Tool99701-0 Base UnitConductivity range: 0.

7 0 to 151 lb/1000bbl( ) to g/m3 (Res: g/m3)Temperature range:-20 C to 150 C (Res: C) Power supply: 9 volt dc battery or mains adaptor 110/240v, 50/60Hz adaptor suppliedSize (HxWxD) / Weight: 20 x 7 x / (including case) 99701-0 Base Unit 90000-3 Centrifuge Tubes 99700-5 99703-0 Stanhope-Seta , London Street, Chertsey, Surrey, KT16 8AP, UK t: +44 (0) 1932 564391 | e: | instruments for quality control, analysis and calibrationSetavap3 Automatic Vapour Pressure Tester (80500-0) ASTM D5191; D6378; D6377; D6897; D5188; EN 13016-1, 2 IP 394, 409, 481, Correlates with ASTM D323; D4953; D5190; D5482; D1267 Rapid automatic vapour pressure Testing Mini methods 1 ml sample volume 0 to 1550 kPa pressure range 0 to 120oC temperature range Integrated shaker Robust measuring chamber/Valves/piston mechanism Results available as DVPE, RVPE VPx Ptot, TVP, Pabs ASVP, T(V/L) Easy to use, large colour touch screen Test memory: >4 Million test reportsSetaVap 3 provides the next generation of automated vapour pressure Testing .

8 The design implements a robust measuring chamber with a movable piston for Testing gasoline, solvents, Crude oils, LPG and similar products in strict compliance with ASTM, IP and ISO methodology. SetaVap 3 is suitable for a broad range of applications including terminals, refineries, mobile Testing , independent laboratories and R&D. SetaVap 3 is extremely easy to operate and can be calibrated in the field, its large colour touch screen allows single press to test functionality and minimises operator involvement. Results are clearly displayed and can be captured using a QR code, emailed, saved to a memory stick, output to LIMS or produced in hard copy with the printer : Rapid Automatic Vapour Pressure Tester (81000-2) ASTM D5191; IP 409; IP 481; IP 394, EN 13016; Correlates with ASTM D323; D5842; D6378; IP 69 Multi-Mode - Ptot, DVPE, EPA, Crude , Pabs Fixed Liquid/Vapour ratio Mini method uses only 3ml sample size Automatic Drain and PurgeA quick and simple to use instrument for determining the vapour pressure of gasoline, solvents, light Crude oils, and similar products using the Mini test is highly automated with step by step instructions and prompts being displayed on the control panel.

9 Once the test procedure has been started operator intervention is only required to inject the sample into the chamber, the purging and cleaning cycle is carried out : Oil Filtration Apparatus (19727-0)ASTM D4807 Determines the sediment in Crude oils by membrane filtration in accordance with ASTM D4807. This test method has been validated for Crude oils with sediments up to approximately mass %.The Apparatus comprises: Insulated Funnel with heating coil (2 parts), bung, clamp, pack of filters (100), Seta steel stand, boss head, clamp, tubes with valves and clips, Buchner flask (500ml), grounding kit including mat, grounding cable assembly, earth bonding plug, earth bonding cord. Supplied with Works : 19727-0 81000-2 Seta Part No:80500-081000-2 Temperature Range:0 to 120 C CPressure Range:0 to 1550kPa0 to 200kPa (0 to 29psi )Pressure Resolution:Conforms to ( )Units of Pressure:kPa or psi (user selectable)kPa or psi (user selectable)Vacuum Requirement:Not Requiredbetter than (abs)Voltage:100/240 VAC 50-60 Hz (Auto)110/120V or 220/240V, 50/60Hz (switchable)Power:230W70 WSize (HxWxD)/ Weight:38 x 23 x 37cm / 16kg 37 x 13 x 20cm / 80500-0 Stanhope-Seta , London Street, Chertsey, Surrey, KT16 8AP, UK t: +44 (0) 1932 564391 | e.

10 | Oil and E&P Testing4KV-6 Viscometer Bath (84200-2)ASTM D445 Up to 6 viscometer tubes 50 litre oil/water bath Temperature stability at 40 C, at 100 C and at 150 C Temperature range ambient to 150 C Digital display with C resolution Toughened glass front panel Integral back lighting50 litre temperature controlled bath that can accommodate up to six standard viscometer tubes. Digital temperature control and an inbuilt cold water cooling coil provide accurate and stable test temperatures from ambient to 150 C. The bath is protected by low liquid level and overtemperature bath is equipped with a toughened glass front window, easily accessible drain valve, integral back lighting, top plate, and provision for reference : Range: Ambient to 150 CTemperature Stability: at 40 C, at 100 C, at 150 CTube Capacity:6 Bath Fluid: Oil or WaterBath Capacity: 50 LitresPower Requirement: (HxWxD) / Weight: 68 x 56 x 33cm / 33kg 84200-2 Viscometer Operating KitsComprises all items required for using glass capillary viscometer tubes.