12.5 mm Modular Panel Potentiometer Cermet …

1 P11S, Sfernice Revision: 19-Jun-20181 Document Number: 51031 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT mm Modular Panel Potentiometer Cermet (P11S)or Conductive Plastic Elements (P11A)DESIGN SUPPORT TOOLSFEATURES mm square single turn Panel control Five shaft diameters and 29 terminal styles Multiple assemblies - up to seven modules Tests according to CECC 41000 or IEC 60393-1 GAM T1 P11S version for industrial, military, and aeronautics applications P11A version for professional audio applications Low current compatibility Shaft and Panel sealed version Up to twenty-one indent positions Rotary and push/push switch options Concentric shafts Custom designs on request Trimmer version T11 (see document no.)

2 51021) Material categorization: for definitions of compliance please see REFERENCE DATAM ultiple moduleUp to 7 modulesSwitch moduleYesDetent moduleYesSpecial electrical lawsA: linear, L: logarithmic, F: reverse logarithmic and others see specificationSealing levelIP 64 Lifespan50K cyclesclick logo to get startedAvailableModelsVERSATILEMODULARCO MPACTROBUSTCONFIGURATION EXAMPLE - Dimensions in millimeters (inches) mm ( ")Single module, single shaft, solder lugs, metric bushing and shaftSingle module, single shaft, vertical mounting, PC pins with support plate, metric bushing and shaftDual modules, single shaft, PC pins with front support plates, imperial bushing and shaft22( ) ( )8( ) ( )ADETAIL A0,9( ) ( )M6 x ( ) ( ) ( ) ( ) ( )5( ) ( ) ( ) ( )M10 x ( ) ( )16( ) ( )8( ) ( ) ( )3/8" x 3/8" ( ) ( ) ( ) ( )8( ) ( ) ( ) ( ) ( ) ( )P11S, Sfernice Revision: 19-Jun-20182 Document Number: 51031 For technical questions, contact.

3 DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT SPECIFICATIONSNote(1)Consult vishay Sfernice for other ohmic valuesELECTRICAL (initial)P11AP11 SResistive elementConductive plasticCermetElectrical travel270 10 270 10 Resistance range (1)Linear taper1 k to 1 M 20 to 10 M Non-linear taper470 to 500 k 100 to M ToleranceStandard 20 % 20 %On request 10 % 5 % or 10 %TaperCircuit diagramPower rating at 70 CLinear W at +70 C1 W at +70 CNon-linear W at +70 W at +70 CMultiple W at +70 C per W at +70 C per moduleTemperature coefficient (typical) 500 ppm 150 ppmLimiting element voltage350 V350 VEnd resistance (typical)2 2 Contact resistance variation (typical)

4 Linear taper1 %2 % or 3 Independent linearity (typical)Linear taper 5 % 5 %Insulation resistance106 M M strength1500 VRMS VRMS dB dB endurance50 000 cycles50 000 cyclesRFSWLA90 %50 %20 %10 %Vs%VeMechanical travel 300 31 31 Electrical travelwith switch 238 15 15 Electrical travel 270 50 %a(1)b(2)c(3)cw13070605040302010001 Ambient Temperature ( C)Rated Power (W) Linear TaperP11S Non-Linear TaperP11A Linear Non-Linear TaperP11S, Sfernice Revision: 19-Jun-20183 Document Number: 51031 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT Nothing stated herein shall be construed as a guarantee of quality or durabilityMECHANICAL (initial)Mechanical travel300 5 Operating torque (typical)Single and dual Ncm to Ncm max.

5 ( to max.)Three to seven modules (per module) Ncm to Ncm max. ( to max.)End stop torque (all bushing except G and concentric shaft configuration)3 mm, 4 mm, and 1/8" dia. shafts35 Ncm max. ( lb-inch max.)6 mm and 1/4" dia. shafts80 Ncm max. ( lb-inch max.)End stop torque for bushing GAll shafts Ncm max. ( lb-inch max.)End stop torque for concentric shaft configuration3 mm and 1/8" dia. shafts25 Ncm max. ( lb-inch max.)6 mm and 1/4" dia. shafts80 Ncm max. ( lb-inch max.)Tightening torque6 mm, 7 mm, and 1/4" dia. bushings150 Ncm max. (13 lb-inch max.)10 mm and 3/8" dia. bushings250 Ncm max. (21 lb-inch max.)Weight7 g to 9 g per module ( oz. to oz.)ENVIRONMENTALP11AP11 SOperating temperature range-55 C to +125 C-55 C to +125 CClimatic category55 / 125 / 2155 / 125 / 56 SealingIP64IP64 MARKING Potentiometer module vishay logo, SAP code of ohmic value, tolerance in %, variation law, manufacturing date (four digits), 3 for the lead 3, product series (P11S, P11A) Switch module Version, manufacturing date (four digits), c for common lead Indent module Version, manufacturing date (four digits)PACKAGING BoxPERFORMANCESTESTSCONDITIONSTYPICAL VALUE AND DRIFTSP11SP11 AElectrical endurance1000 h at rated power90 /30 - ambient temp.

6 70 C RT/RT 2 % 10 %Contact resistance variation 4 % 5 %Change of temperature-55 C to +125 C, 5 cycles RT/RT % %Damp heat, steady state+40 C, 93 % relative humidityP11S: 56 days, P11A: 21 days RT/RT 2 % 5 %Insulation resistance> 1000 M > 10 M Mechanical endurance50 000 cycles RT/RT 5 % 6 %Contact resistance variation 5 % 4 %Climatic sequenceDry heat at +125 C/damp heatcold -55 C/damp heat, 5 cycles RT/RT 1 %-Shock50 g s, 11 ms3 shocks - 3 directions RT/RT % % R1-2/R1-2 % %Vibration10 Hz to 55 mm or 10 g s, 6 h RT/RT % % V1-2/V1-3 % %P11S, Sfernice Revision: 19-Jun-20184 Document Number: 51031 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT ORDERING INFORMATION (part number)P11S2Q0 EASY00103 MAMODELSTYLENUMBEROFMODULESBUSHINGLOCATI NGPEGSHAFTSHAFTSTYLELEADSRESISTANCE CODE/TOLERANCE/TAPER OR SPECIALP11S = Cermet elementA = conductive plastic(audio)1234567 STANDARD RESISTANCE ELEMENT DATASTANDARDRESISTANCEVALUESP11S CERMETP11A CONDUCTIVE PLASTICLINEAR TAPERNON-LINEAR TAPERLINEAR TAPERNON-LINEAR 70 70 70 70 , Sfernice Revision: 19-Jun-20185 Document Number: 51031 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE.

7 THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT Hardware supplied in separate bags Slotted bushing for locking nut optionORDERING INFORMATION (part number)P11S2Q0 EASY00103 MAMODELSTYLENUMBER OFMODULESBUSHINGLOCATINGPEGSHAFTSHAFTSTY LELEADSRESISTANCE CODE/TOLERANCE/TAPER OR SPECIALP11 LOld CodesA 1/4" 1/4"7, 77, 77-3B 1/4" 3/8"71C 1/4" 1/2"72D 1/4" 3/8"71HE 1/4" 1/2"72HF 3/8" 3/8"2, 03, 0-G88 TP, QP, VP, 2P, 7PQ7 8QT6 8TV 10 , CC, CC-3 BUSHING DIMENSIONSPANEL CUT OUTABCKJ HGBushings F and VG HBushings A, B,C, D, E, T and ( ) ( )Bushing GPANEL AND SHAFT SEALED: BUSHING GBUSHING D AND E WITH LOCKING NUTAll models have the same bushing Dia. 8 mm - L 8 mm 8 ( ) ( )8( )ABCW rench 10 or 3/8"JBUSHINGSGTQVABCDEFDIMENSIONS mm ( )DIMENSIONS INCHES ( )AShafts All "1/8"1/8"1/8"1/8"1/4"BBushing 867101/4"1/4"1/4"1/4"1/4"3/8" "3/8"1/2"3/8"1/2"3/8"JLead versions threads/inchWrench , Sfernice Revision: 19-Jun-20186 Document Number: 51031 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE.

8 THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT ORDERING INFORMATION (part number)P11S2Q0 EASY00103 MAMODELSTYLENUMBER OFMODULESBUSHINGLOCATINGPEGSHAFTSHAFTSTY LELEADSRESISTANCE CODE/TOLERANCE/TAPER OR SPECIALOld CodesA =B24B =B30C =B530 =without pegLOCATING PEGS (anti-rotation lug)The locating peg is provided by a plate mounted on the bushing and positioned by the module sides. Four set positions are available, clock face orientation: 12, 3, 6, , B, C, D, E, T, QBUSHINGF, VEFFECTIVEHIGH PEGAll P11 bushings have a double flat. When Panel mounting holes have been punched accordingly, an anti-rotation lug is not d d d pegs are supplied in separate bags with nuts and washers12L369 dP11S, Sfernice Revision: 19-Jun-20187 Document Number: 51031 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE.

9 THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT INFORMATION (part number)P11S2Q0 EASY00103 MAMODELSTYLENUMBER OFMODULESBUSHINGLOCATINGPEGSHAFTSHAFTSTY LELEADSRESISTANCE CODE/TOLERANCE/TAPER OR SPECIALS = slotted L Old CodesAA =roundAB 3 = flattedAJ322RK =knurled/splinedAP = custom shaftBA 1/8" 3/8"CKD = customBB 1/8" 1/2"CMBG 1/8" 5/8"CDMBG 1/8" 5/8"CDBH 1/8" 3/4"CHBJ 1/8" 7/8"CRCC = concentric shaftEA 4 616 DFH 619 IFL625 NFR 650 SGG 1/4" 5/8"VDGH 1/4" 3/4" VHM, VHGJ 1/4" 7/8"VRGL 1/4" 1"VNGO 1/4" "VLSHAFTS in millimeters shaft length is always measured from the mounting shafts are designed by a 3 letters code (3 digits). Shafts slots are aligned to 10 of the wiper standard shafts are slotted except flatted and splined, see exeptions for : Q SPLINED SHAFT: FHKFLATTED SHAFTCUSTOM SHAFTSWhen special shafts are required - flat, threated ends, special shaft lengths, etc.

10 A drawing is COMBINATION OF SHAFT STYLES AND BUSHINGSSHAFT CODESHAFT LENGTH AND STYLE AVAILABLE IN STANDARD (others on request) 7 : FShaft: GHFB ushing: AShaft: at 45 P11S, Sfernice Revision: 19-Jun-20188 Document Number: 51031 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT INFORMATION (part number)P11S2Q0 EASY00103 MAMODELSTYLENUMBER OFMODULESBUSHINGLOCATINGPEGSHAFTSHAFTSTY LELEADSRESISTANCE CODE/TOLERANCE/TAPER OR SPECIALA vailable leadsA00 W00 X00 Y00 Z00A10 W10 X03 Y03 Z03A13 W20 X04 Y04 Z04A14X10Z10A20X13Z13A23X14Z14A24X20Z20X 23Z23X24Z24 FIRST DIGITSECOND DIGITTHIRD DIGITYS oldering lugs0Y = ( ") A, X, Z, W = ( ") pin spacing pins section x ( " x ") ( ") space between modulesXPCB ( ") space between modulesZPCB pins with front support ( ") space between modulesAPCB pins with front and back support ( ") pin spacing pin section x ( " x ")WPCB pins - vertical mounting with 2 extra pins - 1 module ( ")