SPECIFICATION SUBMITTAL - Dimmers And …

1 Contemporary SPECIFICATION series rotary control Large control ProfilePRODUCT FAMILY FEATURES Durable dimmer in a time-honored rotary style For demanding applications up to 2000 watts Captive rotary knobSPECIFICATION SUBMITTALDIMMERS MaximumDescriptionCapacity 1 Model #IncandescentRotary On/Off DimmersSMALLCONTROLS ingle pole600WC-600-Single pole1000WC-1000-LARGECONTROLS ingle pole1500WC-1500-Single pole 2000WC-2000-Push On/Off DimmersSMALLCONTROLS ingle pole600WC-600P-Single pole1000WC-10P-3-way600WC-603P-3-way1000 WC-103P-Electronic Low VoltageFor control of electronic low-voltage loads, use C-600-or C-600P- with Hi-Power 2 4 6 Dimming Low VoltageFor control of magnetic low-voltage loads, use C-600- or C-600P-with Hi-Power 2 4 6 Dimming control of fluorescent loads, use Lutron Hi-lume FDB or Eco-10 TMelectronic dimming ballasts with C-600- or C-600P- and Hi-Power 2 4 6 DimmingModule.

2 See Lutron Wallbox Lighting control Catalog P/N 360-178 for lamps type and ballast model 2 4 6 TMDIMMING MODULESTo increase load capacity up to 30,000W/VA in mostpopular sources, use one C-600- or C-600P- and add up to five dimming modules. Cannot be used with 0-10 VDC exclusive single-gang wallplate provided withproduct. Single-gang replacement plates with knobs sold COLORS/FINISHESM atte Finishes (Ships in 3-5 days)Add color/finish suffix to model number to : C-600-WHWHW hiteBEBeigeHave Questions? Call the Lutron Hotline 800-523-9466 To order Call Lutron Customer Service 610-282-3800 JOB NAMEAREA CONTROLLEDLOCATIONJOB NUMBERTITLEPAGE SERIES STANDARD FEATURES Power-failure memory Voltage compensation Captive rotary knob Superior RFI suppression Electrostatic discharge tested Accessible air-gap switch Heavy-duty components for surge protection and long product lifeLutron controls are rated at 120 VAC, 60Hz unless otherwise noted.

3 Lightlevel withknob; rotate to offRotary DimmerSelect lightlevel withknob; presson/offPreset "(70mm) "(116mm) "(116mm) "(116mm) " *(33mm) "(70mm).65"( )*some models up to "( )WIRING DIAGRAMSW iring Diagram 1 Single-Pole WiringModel # C-600-C-1000-C-1500-C-2000-C-600P-C-10P- Wiring Diagram 34-Way WiringModel # C-603P-C-103P-Wiring Diagram 23-Way WiringModel # C-603P-C-103P-NeutralBlack DimmerBlack or Red Hot120 VAC60 HzLighting LoadGreen GroundWire ConnectorsDERATING/MAXIMUM CAPACITYNo side One side Two sidesections sectionsectionsremovedremovedremoved(Ful l Capacity)(End Units)(Middle Unit)Incandescent Dimmers600W600W500W1000W900W700W1500W125 0W1000W2000W1800W1500 WNote: For multi-gang applications with side sections removed, cut faceplate alongscore mark on the back of the Questions?

4 Call the Lutron Hotline 800-523-9466 To order Call Lutron Customer Service 610-282-3800 ControlsControl Line Side3-WaySwitchDimmerDimmerLighting LoadNeutralRed Red Green Green Black Hot120 VAC60Hz3-WaySwitchLighting Load NeutralRed Red Black Hot120 VAC60 HzControl Load SideGroundWire Connectors control Line SideControl Load SideBlack Red Red Red NeutralHotGreen 120 VAC60Hz3-Way Dimmer4-WaySwitchLighting Load3-WaySwitchNeutralHotGreen 120 VAC60 HzBlack Red 4-WaySwitchLighting Load 3-WaySwitch3-WayDimmerORORG roundWire Connectorsh. Controls shall be capable of operating at the rated capacity;this includes modified capacities for ganging configurationswhich require the removal of fins. Operation at rated capacityshall be possible across the full ambient temperature range,without shortening design To ensure a precise color match between all plastic parts, colorvariation of any matte finish control shall not exceed a delta Eof 1, CIE L*a*b* color units, as defined in ASTM E Dimmer shall provide smooth and continuous Square Lawdimming curve, for the full knob rotation, on their rated load per The IESNA Lighting Handbook, 9th edition, p.

5 Controls shall meet the applicable requirements of UL 20 andUL 1472 referring to the inclusion of a visible, accessible air-gap off switch and the limited short circuit Controls shall withstand voltage surges of up to shall be designed to reduce interference with radio,audio, and video Controls shall incorporate power-failure memory. Shouldpower be interrupted and subsequently returned, the lights will come back on to the same levels set prior to the powerinterruption. Restoration to some other default level is Controls shall not be susceptible to damage or loss of memorydue to static Dimmer shall include voltage compensation to compensatelight output for variation in the AC line-voltage. Dimmers inwhich the light output is not held constant with varying ACline-voltage shall not be Controls shall operate in an ambient temperature range of 0 C (32 F) to 40 C (104 F).

6 R. 3-Way controls shall wire using conventional 3-way and 4-waywire Dimmer shall be capable of operating in either 3-way Contractors shall install all backboxes with a minimum wallboxdepth of Incandescent Dimmers a. Provide incandescent Dimmers for direct control of up to a full20A lighting circuit, which is derated by 20% to 16 Amps perthe Dimmers shall have a high-end of no less than 95% of Remote dimming modules for high power loads a. Where lighting loads exceed the full rated capacity of singledimmers, provide a Centurion incandescent dimmer drivinghigh power modules. High power module and dimmer shall be from the same manufacturer to ensure High power modules shall be remotely High power module shall be rated and UL listed for control ofincandescent, magnetic low voltage, electronic low voltage,fluorescent, and neon/cold cathode loads in increments of2,000 Watts up to 30,000 Wallplates Lutron Centurion Style1.

7 Wallplates shall be manufactured from durable polycarbonateplastic with matte finish, and shall attach to the basic componentswithout using exposed hardware or Visible parts of Dimmers or any wallplate shall exhibit ultravioletstability when tested with multiple actinic light sources as definedin ASTM CONTROLSPART 1 GENERAL SUMMARY A. Scope: Provide, install and test all Dimmers as specified herein for theareas indicated on the drawings, specifications, and load Related Sections: Section 16580 (Ballasts), Section 16570 (DimmingSystems). REFERENCES A. UL 20, UL 1472, CSA, ISO 9001 SYSTEM DESCRIPTION AND OPERATION A. Permanently installed, wallbox mounted Dimmers SUBMITTALS A. Submit manufacturer's standard catalog data giving all application,wiring, and installation information on basic components and wallplatekits.

8 Provide test data and/or samples as required to demonstrateconformance with PART 2 of this QUALITY ASSURANCE A. Manufacturer shall have a minimum of 10 years continuousexperience in manufacturing wallbox dimming Dimmer controls shall be UL listed and CSA approved specifically foreach required load. Manufacturer shall provide file card or certificateupon request. Universal load-type Dimmers shall not be Manufacturer shall maintain ISO 9001 certification and provide a copyof the certificate upon WARRANTY A. All devices shall be covered by a minimum one-year 2 EQUIPMENT ACCEPTABLE MANUFACTURERS A. Lutron Electronics Co., EQUIPMENT A. Controls Lutron Centurion Style1. Performance a. Dimmers shall provide full-range, continuously variable controlof light Controls shall provide a rotary knob allowing the light level tobe set by the user.

9 "Rotate-to-off" controls shall use the rotaryknob to turn the control on and off. "Preset" Dimmers shallprovide a push on/push off switch integral to the rotary. Forpreset Dimmers , when the lights are on, the rotary knob shallchange the light level and when the lights are off, the rotaryknob shall preselect the light level the lights will turn on control on/off function must be accomplished utilizing amechanical air-gap switch to totally disconnect power from the load during "off" condition, no leakage current shall bepresent at the fixture(s).d. Rotary Knob shall be captured behind Preset Dimmers shall be capable of multi-location on andmechanical air-gap off using standard 3-way and Controls shall be able to have their visible plastic partsreplaced, for color changes in the field, without removing thebody of the control from the wall and without requiring Within rated capacity, Dimmers shall be available for directcontrol of incandescent Questions?

10 Call the Lutron Hotline 800-523-9466 To order Call Lutron Customer Service 610-282-3800 SOURCE QUALITY control A. All dimming controls shall be 100% function tested at the time ofmanufacture. Statistical sampling plan shall not be 3 EXECUTION INSTALLATION A. Contractor shall furnish all devices ( Dimmers , accessories, & wallplatekits), labor and other services necessary for the proper installation ofthe devices as indicated on the drawings and specified Contractor shall be responsible for derating dimmer capacity if sidesections are Contractor shall run separate neutral wires in 120/208 Devices shall be installed utilizing manufacturer's recommendedapplication, wiring and installation Contractor to provide seamless wallplate covers per SPECIFICATION for all devices ganged in a common box.