Owner’s Manual - Home Security Systems from …

1 owner s ManualThe Keychain Remote contains the simplisafe Easy Setup Wizard a software program that provides animated instructions and lets you customize your system most easily. Insert the Keychain Remote into a USB port on a computer. No software will be installed. The Easy Setup Wizard will automatically : If the welcome screen does not appear, open My Computer on your desktop and look for the simplisafe drive. On the drive, open the simplisafe application. Follow the on-screen you don t have access to a computer, just follow the instructions in this owner s Manual . Two options for getting started:12visit or call 1-888-95-SIMPLI (957-4675) for additional assistance2 Plan Your Installation608070install near thermostatExtra SirenCarbon Monoxide DetectorKeychain RemoteSmokeDetectorWater Sensorload onto keyrininstall near sleeping areasinstall near water heaterFreeze Sensorinstall in central locationinstall near sleeping areasBase Statioinstall in centra location Note.

2 The system should be installed in accordance with Chapter 2 of the National Fire Alarm Code, ANSI/NFPA 72visit or call 1-888-95-SIMPLI (957-4675) for additional assistance3 Motion SensorKeychain RemoteEntry Sensorinstall near windowsGlassbreak SensorKeypadload onto keyringinstall next to front doorinstall on doors and windowsPanic Buttoninstall in masterbedroominstall 4-5ft high in a cornerBase Stationinstall in central location visit or call 1-888-95-SIMPLI (957-4675) for additional assistance41. Install your Security system : Base Station Set up your Base Station in a central location in your house. Tip: don t install it on the floor.

3 Plug the Base Station into a power outlet using the included power cord. Helpful Information about your Base Station It s the control center of your system , communicating with all of your wireless sensors. It has a built in cellular alarm transmitter that will send us your alarm signals when you activate your simplisafe alarm monitoring service (see page 15). Your Base Station s blue light has 4 modes: a) Off when your system is offb) Glowing steady when your system is armedc) Flashing when there is an error or warning message on the Keypadd) In test mode it will glow bright blue, when your Base Station has good cellular reception.

4 Tip: make sure the power outlet is not controlled by a light switch which could accidentally cut power to the Base Stationvisit or call 1-888-95-SIMPLI (957-4675) for additional assistancevisit or call 1-888-95-SIMPLI (957-4675) for additional assistance5 Install your Keypads Remove the battery activation strip. Adhesive tape has already been installed on the back of the Keypad just peel and stick. If you make a mistake, see How do I move a sensor? on page 19. Adhere the Keypad to the wall by your main information about your Keypad Your default PIN is 1234. We ll help you change that when we personalize your system in just a few : Your alarm system has 3 modes: Away, home and Off.

5 Turn your alarm on by putting it in Away or home mode. Turn your alarm off by putting it in Off buttonsMode iconsoffawayhomeTip: before applying the adhesive tape make sure the surface is clean and dry. Tip: for the most reliable wireless connection, install the Keypad between 10 and 100 feet of the Base or call 1-888-95-SIMPLI (957-4675) for additional assistance6 Install your Motion Sensors Remove the battery activation strip. Place the Motion Sensor on a shelf or adhere it to a wall, approximately 4 to 5 feet off the Information about your Motion Sensor If you have large pets, weighing more than 30 lbs, you can install your motion sensors upside down.

6 This way they ll ignore any movement underneath them. By default, all Motion Sensors will be active in the Away mode only. Put the alarm in the home mode and you can move freely about your home without setting off an : Your Motion Sensor looks straight ahead and 90 to the left and right. It also looks downward at a 45 angle. Mount it in a corner for maximum coverage of your room. Avoid placing the Sensor near a heater, air conditioner, lamp, or electronics (such as a WiFi router). When placed 5 feet off the ground the Motion Sensor should not detect pets under 30 pounds, as long as the pet cannot get within 5 feet of it.

7 Visit or call 1-888-95-SIMPLI (957-4675) for additional assistance7 Install your Glassbreak Sensors Remove the battery activation strip. Adhere the Glassbreak sensor close to a bank of windows or on a wall facing your windows. You can install it up to 20 feet away from the windows you d like to Information about your Glassbreak Sensor Glassbreak Sensors are programmed to listen for the specific frequency of glass breaking. Avoid placing your Glassbreak Sensor in the kitchen, as glasses knocking into each other could trigger a false : Curtains can dull the sound of glassbreaking. If your windows are covered in heavy curtains, place your Glassbreak Sensor within 5-10 feet of your Distance: 20 Feetvisit or call 1-888-95-SIMPLI (957-4675) for additional assistance8visit or call 1-888-95-SIMPLI (957-4675) for additional assistanceInstall your Entry Sensors` Remove the battery activation strip.

8 Align the magnet with the sensor s grooves so the two pieces are less than 2 inches apart when the door or window is : Test the alignment before you adhere each piece. The blue light should flash once when the door or window opens and twice when it closes. Adhere the Sensor on the door and the magnet on the doorframe, or the other way around. There is no right side up. SensorMagnetGroovesClosed magnet is within 2 inches of the sensor, aligned between the sensor ExampleDoor Examplevisit or call 1-888-95-SIMPLI (957-4675) for additional assistance9 Install your Panic Buttons Remove the battery activation strip. Adhere the Panic Button to a wall.

9 Most people install one in their master Information about your Panic Button To trigger a panic alarm you must firmly press your Panic Button for 1-2 full seconds. Tip: install the Panic Button within easy reach in your Master Bedroomvisit or call 1-888-95-SIMPLI (957-4675) for additional assistance10 Install your 105 Decibel Sirens Remove the battery activation strip. Indoor Installation: Adhere Siren in a central location within 100 ft. of the Base Station. Outdoor Installation: Install within 100 ft of your Base Station. Slip the backing bracket off of your Siren and use the included screws to mount the backing under an eve or an awning.

10 Then slide the Siren back onto its backing. Helpful Information about your Siren Be cautious when testing your Siren indoors. Prolonged exposure to a 105 decibel siren can cause hearing damage. We recommend you use ear plugs or stand 5 feet away. When your alarm system has been triggered, the Siren will beep during the entry delay peroid. You can disable the entry delay beeps by removing the backing and pressing the programming button 5 times. You will hear one long tone to confirm the beeps have been disabled. Tip: Install in a cental location. visit or call 1-888-95-SIMPLI (957-4675) for additional assistance11visit or call 1-888-95-SIMPLI (957-4675) for additional assistanceInstall your Carbon Monoxide Detector Remove the battery activation strip.