EHE0200361 RF Programmable Room Thermostat

1 1 User GuideEHE0200361 RF Programmable Room ThermostatThe EHE0200361 RF Programmable room Thermostat is designed to control your heating system efficiently, providing comfortable temperatures when you are at home and energy savings when you are away. The following instructions explain how to program and use the Thermostat to provide the most home comfort at the least Ergonomic user interface featuring an OK-button . Large LCD (Liquid Crystal Display) Screen. 7-day heating program to match your lifestyle, whilst maximising energy savings. 4 independent temperature levels per day (from 5 C to 35 C). Built-in Memory holds the user program of the EHE020036150039991-011 A ScreenBattery Low IndicatorTime DisplayBurner On IndicatorDay IndicatorTemperature DisplayTemperature Change ButtonsTemperature Enquiry Button1239101145 Operating Mode ButtonsOK ButtonBattery CompartmentBattery CoverProgram ButtonsCopy Day ButtonSet Day ButtonTime Change Buttons12131415 Controls Layout6712435891071213111561416168 This section shows you how to setup and run the Thermostat in 3 simple steps:STEP 1: Installing the BatteriesNote: Please follow the instructions in this section only if the Thermostat screen is blank (no symbols or digits are displayed).

2 If the room temperature is already displayed move on to Step 2: Setting the Date and install the Batteries:a. Lift up the front cover of the Thermostat to reveal the battery cover and product Remove the battery cover by pressing down and sliding Insert the 2 x AA LR6 Alkaline Batteries supplied with the Thermostat , ensuring the correct orientation (see Controls Layout on page 2).d. After a short pause the Thermostat will display information on the screen and is now ready for Replace the battery cover by sliding it firmly back into the front of the 2: Setting the TimeTo set the Date and Time:a. Press the D AY button once and the day indicator will begin to Press the D AY button until the correct day is reached (Day 1 = Monday). Press the button to Press either of the or buttons once to enter time setting mode.

3 The LCD screen flashes the time digits (when the unit is powered for the first time the display shows 12:00).e. Use the or buttons to set the correct time then press the button to confirm. Each press of the buttons will change the time by one minute and holding them down will change the time slowly at first and get progressively quicker. Note: If this mode is entered accidentally then press the AUTO, MAN or OFF buttons to 3: Running the Built-in Heating ProgramThe Thermostat is now ready for operation. Press the AUTO button and the built-in heating program will start : The built-in heating program has been designed to provide normal comfort requirements, but if you want to customise the settings please see the next section Programming the EHE0200154 .Setting-up the EHE020036145 Reviewing the Heating ProgramTo review or edit the heating program use the PROGRAM or buttons to navigate between the 4 individual programming periods for that day.

4 Use the DAY button to step through each day of the week, so the complete 7 day heating program can be reviewed or the Heating ProgramTo change the heating program:a. Press either of the PROGRAM or buttons to enter the programming mode. The time / temperature settings for period 1 on Monday (Day 1) will be flashing as shown. The active period is highlighted by a flashing square around the numbers at the bottom of the screen and the selected day is shown with the day To adjust the period start time use the or buttons, the OK? indicator will be displayed to confirm the change. Holding the button down will change the time quickly. Note: If you are pressing the or buttons and the display flashes the next period, it means the next period will be pushed Once the required time is reached press the button to confirm.

5 Note: If the original time setting did not require adjustment press the button to move to step d .MonTueWedThuFriSatSun4321 The Built-in Heating ProgramThe built-in heating program has 4 temperature level changes per day that can be set between and the following day - allowing you to maintain the evening temperature after midnight. Each temperature level can be set between 5 C and 35 C, and adjusted in C increments. The factory default program for heating is as the EHE0200361 Period 1 2 3 4 Time 6:30 8:00 18:00 22:30 Temperature 21 C 18 C 21 C 16 CPeriod 1 2 3 4 Time 8:00 10:00 18:00 23:00 Temperature 21 C 21 C 21 C 16 CMonday to Friday (Day 1 to 5)Saturday & Sunday (Day 6 & 7)Programming the EHE0200361d.

6 The temperature setting for period 1 on Monday (Day 1) will now be flashing. To adjust this press the or buttons and confirm the setting again by pressing the The next time and temperature period will now be active. Adjust this by repeating steps b - d above until all 4 periods are set for Monday or press the AUTO button to run the program as set, at any now have a choice of how to set the program for the next day:f. i) Press the COPY DAY button to copy Monday s program into Tuesday. The display will go blank apart from the non flashing day indicator, which indicates the day copied and the flashing target day to copy the program to. To accept this day press the button. To select a different target day press the D AY button until the flashing day indicator is under the required day, then accept it by pressing the button.

7 Note: Once the target day is confirmed it becomes the day that is copied if the COPY DAY button is pressed again. OR ii) Press the D AY button to move the day indicator to Tuesday (Day 2). The program for that day can then be adjusted by following steps b to e. Programs for the remaining days can be set in the same way, using the D AY button to move to the next exit the programming mode select the desired operating mode by pressing the AUTO, MAN or OFF buttons. Note: To run the adjusted program select the AUTO / Enabling Time PeriodsThe Thermostat has 4 periods each day that can be programmed, but you may not need all of these switch points for your heating requirements. Therefore, any period from 2 to 4 can be removed from (or returned to) the heating program disable or enable time periods:a.

8 To disable unwanted periods go to the desired period (2 to 4) using the PROGRAM or buttons to navigate, ensure the correct period is highlighted with the flashing square symbol. Press and hold the button for at least 2 seconds and the display will indicate the period has been removed from the To enable periods again follow the same procedure as above, navigating to the already disabled period. To enable this period again press and hold the button for at least 2 the Operating ModeThe Thermostat can operate in three different modes: Automatic, Manual or Off. To set the operating mode press either of the AUTO, MAN or OFF buttons. The screen indicates which mode is currently active by displaying AUTO, MAN or OFF. AUTO (automatic) mode sets the Thermostat to follow the built-in temperature program (default or personalised).

9 Operating the Thermostat in this mode is the best way to maintain a high level of temperature comfort whilst maximising your energy savings. MAN (manual) mode sets the Thermostat to act as a simple Thermostat with a fixed setpoint throughout the day. The setpoint can be adjusted from 5 C to 35 C by using the or buttons. The Thermostat will continue to maintain this temperature until another operating mode or temperature is selected. OFF mode sets the Thermostat to control to a minimum temperature setting of 5 C (default) that acts as a frost protection measure for your Normal Operation Temperature Enquiry In AUTO, MAN and OFF operating modes the Thermostat will display the current room temperature. To review the programmed target temperature (the temperature which the Thermostat is trying to maintain) press the button.

10 This target temperature value will be displayed flashing for 5 seconds before returning to the current room temperature value. Temperature Override During normal operation (AUTO mode) the programmed temperature can be adjusted manually by pressing the or buttons or the button. The target temperature will be displayed and flash for 5 seconds - during this time the or buttons can be used to modify the set value. Note: This temperature override is cancelled at the next programmed temperature the TimeTo adjust only the time during normal operation use the or buttons to adjust the time and press the button again to confirm any the EHE0200361 Troubleshooting the EHE0200361 How do I change the batteries on the Thermostat when they run out?The Thermostat constantly monitors the battery power level, which typically lasts for about 2 years before the batteries need to be replaced.