RUBBER MOLDED Table of Contents - SEACON Underwater …

1 (REV 0704) RUBBER MOLDED SERIEST able of ContentsRubber MOLDED Bulkhead Connector Mates .. 50-AIntroduction .. 50-1 General Information .. 50-2 Maintenance Procedures .. 50-3 Typical Right Angle and Straight Connector Indexing .. 50-4 Typical Mated Assembly and Options .. 50-5 RMA-FS and Associated Parts .. 50-6 RMA-MP .. 50-6 RMA-FS .. 50-6 RMA-FS R/A .. 50-6 RMA-MP-SL .. 50-6 RMA-FS-SL .. 50-6 RMA-FSD .. 50-6 RMA-MPD-LP .. 50-6 RMA-MPD-HP .. 50-6 RMA-BCL .. 50-7 XSA-BC .. 50-7 XSA-BCL .. 50-7 XSB-BCL .. 50-7 XSC-BC .. 50-8 XSC-BCL .. 50-8 VMA-FS and Associated Parts .. 50-9 VMA-MP .. 50-9 VMA-FS .. 50-9 VMA-FS R/A.

2 50-9 VMA-MP-SL .. 50-9 VMA-FS-SL .. 50-9 VMA-FSD-LP .. 50-9 VMA-FSD-HP .. 50-9 VMA-MPD .. 50-9 VMA-BCL .. 50-10 VSA-BC .. 50-10 VSA-BCL .. 50-10 VSB-BCL .. 50-10 RMF-FS and Associated Parts .. 50-11 RMF-MP .. 50-11 RMF-FS .. 50-11 RMF-FS R/A .. 50-11 RMF-FSD .. 50-11 RMF-MPD-HP .. 50-11 RMF-MPD-LP .. 50-11 XSF-BC .. 50-12 XSF-BCL .. 50-12 XSFDE-BCL .. 50-12 VMF-FS and Associated Parts .. 50-13 VMF-MP .. 50-13 VMF-FS .. 50-13 VMF-FS R/A .. 50-13 VMF-FSD-HP .. 50-13 VMF-FSD-LP .. 50-13 VMF-MPD .. 50-13 VMF-BCL .. 50-14 VSF-BCL .. 50-14 LMG-FS and Associated Parts .. 50-15 LMG-MP .. 50-15 LMG-FS .. 50-15 LMG-FS R/A.

3 50-15 LMG-FSD .. 50-15 LMG-MPD-LP .. 50-15 LMG-MPD-HP .. 50-15 LSG-BC .. 50-16 LSG-BCL .. 50-16 LSG-BC-SC .. 50-17 LSG-BC-HP .. 50-18 RMG-FS and Associated Parts .. 50-19 RMG-MP .. 50-19 RMG-FS .. 50-19 RMG-FS R/A .. 50-19 RMG-FS WOC .. 50-19 RMG-MP WOC .. 50-19 RMG-FSD .. 50-19 RMG-MPD .. 50-19 RMG-BCL .. 50-20 XSG-BCL .. 50-20 XSG-BCL-P-R/A .. 50-20 XSG-PBC .. 50-21 XSG-PBCL .. 50-21 XSG-PBCLM .. 50-21 RMGS-BC .. 50-22 RMGS-BCL .. 50-22 VMG-FS and Associated Parts .. 50-23 VMG-MP .. 50-23 VMG-FS .. 50-23 VMG-FS R/A .. 50-23 VMG-FS WOC .. 50-23 VMG-MP WOC .. 50-23 VMG-FSD .. 50-23 VMG-MPD .. 50-23 VMG-BCL.

4 50-24 VSG-BCL .. 50-24 VSG-PBC .. 50-24 VSG-PBCL .. 50-25 VSG-PBCLM .. 50-25 RMK-FS and Associated Parts .. 50-26 RMK-MP .. 50-26 RMK-FS .. 50-26 RMK-FS R/A .. 50-26 RMK-FS WOC .. 50-26 RMK-MP WOC .. 50-26 RMK-FSD .. 50-26 RMK-MPD .. 50-26 RMK-BCL .. 50-27 XSK-BCL .. 50-27 XSK-DEBCL .. 50-27 VMK-FS and Associated Parts .. 50-28 VMK-MP .. 50-28 VMK-FS .. 50-28 VMK-FS R/A .. 50-28 VMK-FS WOC .. 50-28 VMK-MP WOC .. 50-28 VMK-FSD .. 50-28 VMK-MPD .. 50-28 VMK-BCL .. 50-29 VSK-BCL .. 50-29 Special Assemblies .. 50-30 Locking Sleeves .. 50-31A-FLS-D .. 50-32A-MLS-D .. 50-32F-FLS-D .. 50-32F-MLS-D .. 50-32 VSF-FLS-D.

5 50-32 VSF-MLS-D .. 50-32G-FLS-D .. 50-32G-MLS-D .. 50-32G-FLS-S .. 50-32G-MLS-S .. 50-32G-FLS-X .. 50-32G-MLS-D .. 50-32K-FLS-D .. 50-32K-MLS-D .. 50-32K-FLS-S .. 50-32K-MLS-S .. 50-32K-FLS-X .. 50-32K-MLS-D .. 50-32 RUBBER MOLDED Quick Reference Mating Table .. 50-3350-A(REV 0704)1/4-28 XSA-BCTHD5/16-24 THD1/4-28 THD3/8-24 THDTHD3/8-241/4-28 THD5/16-24 THD5/16-24 THDVSA-BCRMA-BCLXSA-BCLVMA-BCLVSA-BCLXSB -BCLXSC-BCXSC-BCLRMA FSVMA FSRMA-FS R/AVSB-BCLPage : Torque values referenced in this literature assume installation intodry metal threads. Please contact the factory for HPTHD3/4-16 LSG-BC SC(formerly LSK-BC SC)LMG FSLMG FS R/ANOTE:LSG-3-BC HP: 1/2-20 LSG-4-BC HP: 9/16-18 LSG-6-BC HP: 9/16-1811/16-16 THD3/8-24 THD3/8-24 THDXSFDE-BCL(formerly XSDE-BCL)XSF-BCXSF-BCLRMF FSRMF FS R/A50-12 Page FSVMF FS R/A50-14 Page :LSG-3-BC: 1/2-20 LSG-4-BC: 9/16-18 LSG-6-BC: 9/16-18 NOTE:LSG-3-BCL: 1/2-20 LSG-4-BCL: 9/16-18 LSG-6-BCL: 9/16-18 RUBBER MOLDED BULKHEAD CONNECTOR MATESVISUAL INDEX50-B(REV 0704)1-14 THD1-14 THDVMK FSRMK FSRMK FS R/AXSKDE-BCL1 1/2-14 THDRMK-BCLXSK-BCLVMK-BCLVSK-BCLPage FSVMG FS1/2-20 THDVSG-PBCLM1/2-20 THDVSG-PBCLRMG FS R/ANOTE.

6 RMGS-BC (1/2" NPT)RMGS-BCL (3/4" NPT)VMG-BCLVSG-BCLRMG-BCL50-20 RMGS-BC50-22 RMGS-BCL50-22 XSG-BCL50-20 XSG-BCL-P-R/A50-20 Page : Torque values referenced in this literature assume installation into dry metal threads. Please contact the factory for MOLDED BULKHEAD CONNECTOR MATESVISUAL INDEX50-1(REV 0704)INTRODUCTIONOur standard RUBBER MOLDED series typically consists of an in-line female neoprene connector mated to a glassreinforced epoxy (XS) bulkhead connector. Various sizes are available ranging from single contact connectors upthrough 12 contact connectors. Most are available with pins and sockets reversed to help prevent mismating ofconnectors, which otherwise look identical.

7 This also allows for socket type contacts in a connector where there isa possibility of a "power-on" situation. Many of the bulkhead type connectors are available in 316 Stainless Steel,and can also be manufactured of any of the exotic metals. Male in-line connectors round out the series allowingfor in-line mated sets not requiring bulkhead penetration. In addition, the WOC (without cable) type connectorsallow for field installation in the event that a connector is damaged while at sea and needs replacing, or for longcable lengths that make cable transportation cost time proven RUBBER MOLDED series is one of our most inexpensive lines and has been used on all types ofunderwater instrumentation including: Underwater lighting, communications, ROV's, thermistor arrays, hydrophonearrays, and all types of sonar systems.

8 The contacts are gold plated per ASTM-B-488 and the series is rated up to20,000 psi in a mated NUMBERING SYSTEMCONNECTORSRMG-6-FS-R/ARight Angle (optional)Female SocketNumber of ContactsSizeRubber MoldedBulkhead ConnectorsLSGlass Reinforced Epoxy- Special VersionRMMetal ShellVMReversed Metal ShellVSReversed Glass Reinforced EpoxyXSGlass Reinforced EpoxyBCBulkhead ConnectorBCLBC w/Locking ThreadCCOAXDED ouble EndedHPHigh PressureIDCI nboard DisconnectPPigtailsIn-Line ConnectorsLMRubber MOLDED -Special VersionRMRubber MoldedVMReversed RUBBER MoldedFSFemale SocketFSDF emale Socket DummyMPMale PlugMPDMale Plug DummyFIField InstallableHPHigh PressureLPLow PressureSLSlip-on SeriesWOCW ithout CableR/ARight AngleSCSolder CupTHThermistor Housing50-2(REV 0704)

9 GENERAL INFORMATIONRUBBER MOLDED AND ASSOCIATED SERIESAPPLICATIONS:Standard, Reversed RUBBER MOLDED SeriesApplications requiring light to medium ruggednessHazardous environmentsField installable applicationsGlass Reinforced Epoxy SeriesApplications requiring medium ruggednessHazardous environmentsPower transmissionSignal telemetryMetal Shell SeriesApplications requiring heavy ruggednessHazardous, rugged environmentsPower transmissionSignal telemetryCABLE: RUBBER MOLDED SeriesConnector's power capability may be limited by amperage and voltage rating of cable to which it ismolded to. With the exception of field installable connectors, the in-line series are provided on a stan-dard 18" length of 18 AWG SO cable unless otherwise Reinforced Epoxy Series & Metal Shell SeriesConnector's power capability may be limited by amperage and voltage rating of must specify if pigtails are to be : Torque values referenced in this literature assume installation intodry metal threads.

10 Please contact the factory for (REV 0704)MAINTENANCE PROCEDURESCONNECTORSMAINTENANCEThe following procedures detail the maintenance requirements for the RUBBER MOLDED Series and theirassociated parts. Even though this procedure appears simple, only qualified technicians should per-form the maintenance. If connectors are periodically unmated SEA CON recommends the unmating ensure connectors are free of foreign contaminates. Visually check for andnote any damage or unmating visually check for and note any damage, cuts or any grease, moisture or foreign particles from connectors and sealing surface the event the internal contact surfaces are dirty or have been exposed to water, the connec-tor should be flushed with distilled or deionized water and thoroughly surface should be dried using a low pressure (15 - 25 psi) gas stream of dry nitrogen orfiltered compressed air (dry nitrogen is preferred).