GR-1600XL - TADANO America Corporation

1 Note : Dimension is with boom angle at radius 6 wheel steer32' 6" 2 wheel steer48' 11" swing of counterweight15' 1" are subject to change without DIMENSIONS ( R25 Tires)160 Ton Capacity (145 Metric Tons)HYDRAULIC ROUGH TERRAIN CRANEDIMENSIONSGR-1600 XLCRANE SPECIFICATIONSBOOMWIRE ROPE - Non-rotating 3/4" (19mm) 7x35 section boom, single cylinder telescoping with pinning system,Breaking Strength 79,400 lbs (36,000 kg) ' - ' ( - ), of round box constructionwith seven sheaves, 15-3/4" ( ) root diameter, at boom BLOCKSTwo easily removable wire rope guards, rope dead end provided110 ton (100 metric ton) - 7 sheaves with swivel hook blockon both sides of boom head. Boom telescope sections are ton ( metric ton) - Weighted hook ball with swivel and safety wear pads both vertically and speed ' in 450 counterweight (40,100 + 24,500 = 64,600 lbs)BOOM ELEVATION - By a double acting hydraulic cylinder withholding valve.

2 Elevation minus o - o, combination controls for handHYDRAULIC SYSTEMor foot operation. Boom angle speed reduction and soft stop - Two variable piston pumps for crane raising speed 20o to 60o in 28 gear pump for steering, slewing and optional by carrier engine. Pump disconnect for crane isJIB - Two stage bi-fold lattice type with 0 o, 20 o or 40 o offset (tilt type).engaged/ disengaged by rotary switch from operator's sheave, 17-5/16" ( ) root diameter, at the head of bothjib sections. Stored alongside base boom section. Jib length is CONTROL VALVES - Multiple valves actuated by pilot ' ( ) or ' ( ). Assistant cylinders for mountingwith integral pressure relief stowing, controlled at right side of superstructure. Self stowing jib mounting - 202 gallon (763 lit.) capacity. External sight level JIB (*Optional)FILTRATION - BETA10=10 return filter, full flow with bypassTwo lattice insert sections ( ' each) to extend to '.

3 Protection, located inside of hydraulic reservoir. Accessible foreasy DUTY JIB (*Optional)Two sheaves, heavy lifting jib with 20o or 40o offset (tilt type).OIL COOLER - Air cooled fan length is ' ( ).AUXILIARY LIFTING SHEAVE (SINGLE TOP)CAB AND CONTROLSS ingle sheave, 17-5/16" ( ) root diameter. Mounted to mainboom head for single line work (storable).Both crane and drive operations can be performed from one cabmounted on rotating BLOCK - Pendant type over-winding cut out devicewith audio-visual (FAILURE lamp/BUZZER) warning side, 1 man type, tilting cab, steel construction with sliding dooraccess and safety glass windows opening at side. Door window isSLEWING powered control. Windshield glass window and roof glass windowHydraulic axial piston motor through planetary slewing speedare shatter-resistant.

4 Tilt-telescoping steering wheel. Adjustable reducer. Continuous 360 o full circle slewing on ball bearing turncontrol lever stands for slewing, boom elevating, boom telescoping,table at -1 {rpm}. Equipped with manually locked/releasedauxiliary hoist and main hoist. Control lever stands can changeslewing brake. A 360o positive slewing lock manually engaged in positions and tilt for easy access to cab. 3 way adjustableTwin slewing system: Free slewing or lock slewing controlled byoperator's seat with high back, headrest and armrest. Engineselector switch on front knob. Foot operated controls: boom elevating,boom telescoping, service brake and engine throttle. MAIN HOIST - Variable speed type with grooved drum driven byHot water cab heater and air axial piston motor through speed reducer. Power loadlowering and raising.

5 Equipped with automatic brake (neutral brake) Dash-mounted engine start/stop, monitor lamps, cigarette lighter,and counterbalance valve. Controlled independently of auxiliary selector switch, parking brake switch, steering modeEquipped with cable follower and drum rotation switch, power window switch, pump engaged/disengagedswitch, slewing brake switch, telescoping/auxiliary hoist selectDRUM - Grooved 15" ( ) root diameter x 29-1/4" ( ) , outrigger controls, free slewing / lock slewing selector switch,Wire rope: 1050' of 3/4" diameter rope (320m of 19mm).eco mode switch, high speed hoist (main/aux) switch and capacity: 1293' (394m) 7 single line pull (available): 21,800 lbs (9,900kg).Instruments - Torque converter oil temperature, engine waterMaximum line speed: 505 FPM (154m/min) at the 6th , air pressure, fuel, speedometer, tachometer,hour meter and odometer / tripmeter.

6 Hydraulic oil pressure is AUXILIARY HOIST - Variable speed type with grooved drum drivenmonitored and displayed on the AML-C display hydraulic axial piston motor through speed reducer. Power loadlowering and raising. Equipped with automatic brake (neutral brake)and counterbalance valve. Controlled independently of main with cable follower and drum rotation - Grooved 15" ( ) root diameter x 29-1/4" ( )wide. Wire rope: 738' of 3/4" diameter rope (225m of 19mm).Drum capacity: 1293' (394m) 7 single line pull (available): 21,800 lbs (9,900kg).Maximum line speed: 476 FPM (145m/min) at the 5th electronic LOAD MOMENT INDICATOR system Main hoist / auxiliary hoist select(AML-C) including: Drum rotation indicator (audible and visible type) main and Control lever lockout functionauxiliary hoist Boom position indicator Outrigger state indicatorTADANO AML-C monitors outrigger extended length and Boom angle / boom length / jib offset angle / jib length / loadautomatically programs the corresponding "RATED LIFTING radius / rated lifting capacities / actual loads read outCAPACITIES" table Ratio of actual load moment to rated load momentindicationOperator's right hand console includes transmission gear Automatic Speed Reduction and Slow Stop function selector and sight level bubble.

7 Upper console includes on boom elevation and slewing working light switch, roof washer and wiper switch Working condition register switchemergency outrigger set up key switch, Load radius / boom angle / tip height / slewing rangejib equipped/removed select switch, eco mode switch,preset functionhigh speed hoist (main / aux) switch, Cab tilt switch, External warning lampand air conditioning control switch. Slewing lock lever. Tare function Fuel consumption monitorNOTE: Each crane motion speed is based on SPECIFICATIONSTYPE - Rear engine, left hand steering, driving axle 2-waySUSPENSION selected type by manual switch, 6x2 1st axle drive, 6x4 1st and1st axle - Rigid mounted to axle and 3rd axles - "Hydro-Pneumatic suspension cylinders" withleveling adjustment and - High tensile steel, all welded mono-box SYSTEMS - Service: Air over hydraulic disc brakes onTRANSMISSION - Electronically controlled full automaticall 6 wheels.

8 Parking/Emergency: Spring applied-air releasedtransmission. Torque converter driving full powershift withbrake acting on input shaft of 1st and 3rd axles. Auxiliary: Electro-driving axle selector. 5 forward and 2 reverse speeds, constantpneumatic operated exhaust speeds - high range - 2 wheel drive; 4 wheel driveTIRES - R253 speeds - low range - 4 wheel driveOUTRIGGERS - Four hydraulic, beam and jack SPEED - mph (15 km/h) *with counterweightVertical jack cylinders equipped with integral holding valve. EachTRAVEL SPEED - mph (4 km/h) *without counterweightoutrigger beam and jack is controlled independently from extend to 26'10-7/8" ( m) center-line and retract toGRADEABILITY (tan )within 10' 10-1/2" ( m) overall width with floats. 44% *with counterweight 64,600 lbs ( t)Outrigger jack floats are attached thus eliminating the need of manually 52% *with counterweight 40,100 lbs ( t)attaching and detaching them.

9 Controls and sight bubble located Machine should be operated within the limit of engine crankcasein superstructure cab. Four outrigger extension lengths are provideddesign (30o - Cummins )with corresponding "RATED LIFTING CAPACITIES" for crane dutyin confined outrigger boxes for ease of axle - Full floating type,Min. Extension 9' 9-3/4" ( ) center to center steering and driving axle with planetary Extension18' 1/2" ( ) center to center2nd axle -Steering axleMid. Extension23' 11-3/8" ( ) center to center3rd axle - Full floating type,Max. Extension 26' 10-7/8" ( ) center to center steering and driving axle with planetary size(Diameter) 1' 10-1/2" ( )STEERING- Hydraulic power steering controlled by steeringwheel. Four steering modes available: 2 wheel front, 4 wherear, 6 wheel coordinated and 6 wheel crabEmergency steering deviceENGINEM odel Cummins [Tier4]Radiator Fin and tube core, thermostat controlledType Direct injection dieselFan, in.

10 (mm) Suction type, 9-blade, 28 (711) of cylinders6 Starting 24 voltCombustion 4 cycle, turbo charged and after cooledCharging 24 volt system, negative groundBoreXStroke, in.(mm) x (107 x 124)Battery 2-120 amp. HourDisplacement, cu. in (liters) 409 ( )Compressor, air, CFM(l /min) CFM (481) at 2,400rpmAir inlet heater 24 volt preheatHorsepower (kW) Gross 270 (201) at 2,000rpmAir cleaner Dry type, replaceable elementTorque, Max. ft-lb (Nm) 730 (990) at 1,500rpmOil filter Full flow with replaceable elementCapacity, gal.(liters)Fuel filter Full flow with replaceable elementCooling water (29)Fuel tank, gal.(liters) (300), right side of carrierLubrication (15)Cooling Liquid pressurized, recirculating (300) (38)3- Six section boom, single cylinder telescoping with pinning system- Cummins turbo charged after cooled ' - ' ( - )(270HP) with exhaust brake- ' or ' ( or ) bi-fold lattice jib (tilt type)- Electronic controlled automatic transmission drivenwith 0 o, 20 o or 40 o pinned offsets and self stowing pins.