Chip And Pin

USB to serial chip CH340 - SparkFun Electronics

CH340 chip set up USB pull-up resistor internal, UD+ and UD- pins must be connected to USB bus directly. CH340 chip set up power up reset circuit internal. When CH340 chip is working normally, the outside must supply 12MHz clock signal to XI pin. In

  Chip

Single chip 2.4 GHz Transceiver nRF24L01

• 20-pin package (QFN20 4x4mm) • Uses ultra low cost +/- 60 ppm crystal • Uses low cost chip inductors and 2-layer PCB • Power supply range: 1.9 to 3.6 V GENERAL DESCRIPTION nRF24L01 is a single chip radio transceiver for the world wide 2.4 - 2.5 GHz ISM band. The transceiver consists of a fully integrated frequency synthesizer, a power

  Chip, Nrf24l01

PL-2303HX Edition (Chip Rev D) USB to Serial Bridge ...

o Suspends power of chip when idle (COM port is closed) Provides royalty-free USB to Virtual COM Port drivers for Windows, Mac, Linux, Android -40 oC to 85 oC Operating Temperature Small footprint 28-pin SSOP or 32-pin QFN IC packages (RoHS compliant and Pb …

  Chip

ES9038Q2M 32-Bit Stereo Low Power Audio DAC Analog ...

chip-to-chip gain variation is minimized via a built-in auto gain calibration circuit. The ES9038Q2M SABRE 32 Reference DAC sets the standard, SABRE SOUND ® , for HD audio performance, typically consumes 40mW in normal operation mode (1.3mW in standby mode), and comes in an easy-to-use 30-QFN (3mm x

  Power, Audio, Chip, Stereo, Es9038q2m, Es9038q2m 32 bit stereo low power audio dac

How to Program an IC Chip

•Place chip in the programmer in the ZIF socket •Pull lever to open slots •Place in programmer at the bottom of the slots with pin 1 pointing towards lever •Close slots by moving lever to original position. NOTE: This step only needed if you are using a UV erasable device (i.e. 2532A or …

  Chip

TP4056 1A Standalone Linear Li-lon Battery Charger with ...

pin draws less than 2uA current in chip disable mode or in sleep mode. BAT pin provides charge current to the battery and provides regulation voltage of 4.2V. (Pin6): Open Drain Charge Status Output When the battery Charge Termination, the pin is pulled low by an internal switch, otherwise pin is in high impedance state.

  Chip

FE1.1 USB 2.0 H SPEED 4-PORT H CONTROLLER

DPU 31 16 UT The D+ pin of the Upstream Facing Port. XRSTJ 34 17 I External Reset, active low, is an optional source of chip reset signal, beside the build-in Power-On-Reset.

  Chip

ENC28J60 Data Sheet

Oct 26, 2012 · SCK 8 4 I ST Clock in pin for SPI interface.(3) CS 9 5 I ST Chip select input pin for SPI interface.(3,4) RESET 10 6 I ST Active-low device Reset input.(3,4) VSSRX 11 7 P — Ground reference for PHY RX. TPIN- 12 8 I ANA Differential signal input. TPIN+ 13 9 I ANA Differential signal input. RBIAS 14 10 I ANA Bias current pin for PHY.

  Chip

LMC6484 CMOS, Quad, Rail-to-Rail Input and Output ...

Current at power supply pin 40 mA TJ Junction temperature(6) 150 °C Tstg Storage temperature, Tstg −65 150 °C (1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process. Manufacturing with less than 500-V HBM is possible with the necessary precautions.