Example: confidence
ENC28J60 Data Sheet
Oct 26, 2012 · SCK 8 4 I ST Clock in pin for SPI interface.(3) CS 9 5 I ST Chip select input pin for SPI interface.(3,4) RESET 10 6 I ST Active-low device Reset input.(3,4) VSSRX 11 7 P — Ground reference for PHY RX. TPIN- 12 8 I ANA Differential signal input. TPIN+ 13 9 I ANA Differential signal input. RBIAS 14 10 I ANA Bias current pin for PHY.
Tags:
Information
Domain:
Source:
Link to this page:
Documents from same domain
Low Quiescent Current LDO - Microchip Technology
ww1.microchip.com2005-2016 Microchip Technology Inc. DS20001826D-page 1 MCP1700 Features: • 1.6 µA Typical Quiescent Current • Input Operating Voltage Range: 2.3V to 6.0V
MTCH6102 Low-Power Projected Capacitive Touch …
ww1.microchip.com2014 Microchip Technology Inc. DS40001750A-page 1 Description: Microchip’s MTCH6102 is a turnkey projected capacitive touch controller that simplifies adding
Power Factor Correction in Power Conversion …
ww1.microchip.com© 2007 Microchip Technology Inc. DS01106A-page 2 AN1106 FIGURE 1: CURRENT WAVEFORMS WITH AND WITHOUT PFC These waveforms illustrate that …
2.7V to 5.5V Single Supply CMOS Op Amp
ww1.microchip.comMCP601/1R/2/3/4 DS21314G-page 2 © 2007 Microchip Technology Inc. 1.0 ELECTRICAL CHARACTERISTICS Absolute Maximum Ratings † VDD –VSS.....7.0V
Data Encryption Routines for PIC24 and dsPIC Device
ww1.microchip.com© 2006 Microchip Technology Inc. DS01044A-page 1 AN1044 INTRODUCTION Currently, there are three data encryption standards approved …
MCP6021/1R/2/3/4 - Rail-to-Rail Input/Output, 10 …
ww1.microchip.com2001-2017 Microchip Technology Inc. DS20001685E-page 1 MCP6021/1R/2/3/4 Features • Rail-to-Rail Input/Output • Wide Bandwidth: 10 MHz (typical)
MCP1703 250 mA, 16V, Low Quiescent Current
ww1.microchip.com2010 Microchip Technology Inc. DS22049E-page 1 MCP1703 Features: • 2.0 µA Typical Quiescent Current • Input Operating Voltage Range: 2.7V to16.0V
PIC32 GUI Development Board with Projected …
ww1.microchip.comPIC32 GUI Development Board with Projected Capacitance (PCAP) Touch Information Sheet Microchip Technology Inc.
RN4020 Bluetooth Low Energy Module User’s Guide
ww1.microchip.comRN4020 BLUETOOTH LOW ENERGY MODULE USER’S GUIDE 2014 Microchip Technology Inc. DS70005191B-page 7 Preface INTRODUCTION This chapter contains general information that will be useful to know before using the
Using SAM-BA for Linux on SAMA5D3 Xplained
ww1.microchip.comAN-8995 – Using SAM-BA for Linux on SAMA5D3 Xplained: 42328A−06/2014 Page 5 of 19 2. Setup With Ubuntu distributions, a user has to be member of the dialout group to access serial devices like
Related documents
USB to serial chip CH340 - SparkFun Electronics
cdn.sparkfun.comCH340 chip set up USB pull-up resistor internal, UD+ and UD- pins must be connected to USB bus directly. CH340 chip set up power up reset circuit internal. When CH340 chip is working normally, the outside must supply 12MHz clock signal to XI pin. In
Single chip 2.4 GHz Transceiver nRF24L01
www.sparkfun.com• 20-pin package (QFN20 4x4mm) • Uses ultra low cost +/- 60 ppm crystal • Uses low cost chip inductors and 2-layer PCB • Power supply range: 1.9 to 3.6 V GENERAL DESCRIPTION nRF24L01 is a single chip radio transceiver for the world wide 2.4 - 2.5 GHz ISM band. The transceiver consists of a fully integrated frequency synthesizer, a power
PL-2303HX Edition (Chip Rev D) USB to Serial Bridge ...
www.prolific.com.two Suspends power of chip when idle (COM port is closed) Provides royalty-free USB to Virtual COM Port drivers for Windows, Mac, Linux, Android -40 oC to 85 oC Operating Temperature Small footprint 28-pin SSOP or 32-pin QFN IC packages (RoHS compliant and Pb …
ES9038Q2M 32-Bit Stereo Low Power Audio DAC Analog ...
www.esstech.comchip-to-chip gain variation is minimized via a built-in auto gain calibration circuit. The ES9038Q2M SABRE 32 Reference DAC sets the standard, SABRE SOUND ® , for HD audio performance, typically consumes 40mW in normal operation mode (1.3mW in standby mode), and comes in an easy-to-use 30-QFN (3mm x
How to Program an IC Chip
www.princeton.edu•Place chip in the programmer in the ZIF socket •Pull lever to open slots •Place in programmer at the bottom of the slots with pin 1 pointing towards lever •Close slots by moving lever to original position. NOTE: This step only needed if you are using a UV erasable device (i.e. 2532A or …
TP4056 1A Standalone Linear Li-lon Battery Charger with ...
dlnmh9ip6v2uc.cloudfront.netpin draws less than 2uA current in chip disable mode or in sleep mode. BAT pin provides charge current to the battery and provides regulation voltage of 4.2V. (Pin6): Open Drain Charge Status Output When the battery Charge Termination, the pin is pulled low by an internal switch, otherwise pin is in high impedance state.
FE1.1 USB 2.0 H SPEED 4-PORT H CONTROLLER
cdn-shop.adafruit.comDPU 31 16 UT The D+ pin of the Upstream Facing Port. XRSTJ 34 17 I External Reset, active low, is an optional source of chip reset signal, beside the build-in Power-On-Reset.
LMC6484 CMOS, Quad, Rail-to-Rail Input and Output ...
www.ti.comCurrent at power supply pin 40 mA TJ Junction temperature(6) 150 °C Tstg Storage temperature, Tstg −65 150 °C (1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process. Manufacturing with less than 500-V HBM is possible with the necessary precautions.