I2c interface
Found 9 free book(s)
I2C Serial Interface 1602 LCD Module - handsontec.com
handsontec.comI2C Serial Interface 1602 LCD Module This is I2C interface 16x2 LCD display module, a high-quality 2 line 16 character LCD module with on-board contrast control adjustment, backlight and I2C communication interface. For Arduino beginners, no more cumbersome and complex LCD driver circuit connection.
Lidar Lite v3 Operation Manual 2 and Technical …
static.garmin.comI2C Interface This device has a 2-wire, I2C-compatible serial interface (refer to I2C-Bus Specification, Version 2.1, January 2000, available from Philips Semiconductor). It can be connected to an I2C bus as a slave device, under the control of an I2C master device. It supports 400 kHz Fast Mode data transfer.
UM10204 I2C-bus specification and user manual
www.pololu.comI2C interface is more successful in the marketplace due to the wide variety of existing peripheral devices available. 3. The I2C-bus protocol 3.1 Standard-mode, Fast-mode and Fast-mode Plus I2C-bus protocols Two wires, serial data (SDA) and serial clock (SCL), carry information between the devices connected to the bus.
SC16IS740/750/760 Single UART with I2C-bus/SPI interface ...
www.nxp.comSingle UART with I2C-bus/SPI interface, 64-byte FIFOs, IrDA SIR 5. Block diagram Fig 1. Block diagram of SC16IS750/760 I2C-bus interface Fig 2. Block diagram of SC16IS740 I2C-bus interface SC16IS750/760 16C450 COMPATIBLE REGISTER SETS 002aab014 VDD I2C-BUS TX RX RTS GPIO REGISTER CTS GPIO[3:0] XTAL1 XTAL2 SCL SDA A0 IRQ I2C/SPI 4 A1 …
USB to I2C Example using the FT232H and FT201X devices
www.ftdichip.comFT232H as a USB-to-I2C Master interface. The FT232H would be used where the PC application needs to communicate with one or more I2C slaves. For example, the application may be taking readings from Analog to Digital converters which have 2an I C interface, or may be reading and writing to an EEPROM chip or I/O expander.
24AA64/24LC64 64K I2C Serial EEPROM
ww1.microchip.com• 2-wire serial interface bus, I2C™ compatible • Cascadable for up to eight devices • Schmitt Trigger inputs for noise suppression • Output slope control to eliminate ground bounce • 100 kHz (24AA64) and 400 kHz (24LC64) com-patibility • Self-timed write cycle (including auto-erase) • Page-write buffer for up to 32 bytes
PLDM Base Specification - Home | DMTF
www.dmtf.orgPLDM is designed to be an effective interface and data model that provides efficient access to low-level platform inventory, monitoring, control, event, and data/parameters transfer functions. For example, temperature, voltage, or fan sensors can have a …
PCA9548A 8-channel I2C-bus switch with reset
www.nxp.comI2C-bus interface logic; compatible with SMBus standards Active LOW reset input Three address pins allowing up to eight devices on the I2C-bus Channel selection via I2C-bus, in any combination Power-up with all switch channels deselected Low Ron switches Allows voltage level translation between 1.8 V, 2.5 V, 3.3 V and 5 V buses
with SPI and I2C
www.skyworksinc.comThe I2C_SEL pin must be low for SPI. The SPI protocol has a command format that must be followed for reading and writing transactions. The SPI commands that the applicable timing devices support are defined in the following table: Table 2.1. SPI Commands and Expected Command Format Instruction 1st Byte. 1. 2nd Byte 3rd Byte Nth Byte. 2, 3