Recommended Assembly Torques
Found 10 free book(s)
FASTENER TORQUE CHARTS - Imperial Supplies
www.imperialsupplies.comThe above recommended assembly torques are offered as a guide only. Torque specifications, especially for critical joints, should be determined . under actual assembly conditions due to the many variables involved which are difficult to predict and do affect the torque-tension relationship.
FITTING ASSEMBLY GUIDELINES
www.stoneagetools.comUnderstanding the proper preparation and assembly of high ... THREAD SIZE RECOMMENDED TORQUE 1/16 NPT 4–5 Nm 3–4 ft-lb 1/8 NPT 20–23 Nm 15–17 ft-lb ... If you apply these torques without an anti-seize compound on stainless steel connections, they will gall and
SAE J1926-1 — SAE Straight Thread O-ring Port (ISO 11926-1)
www.goodyearrubberproducts.com6) Maximum recommended spotface depth to permit sufficient wrench grip for proper tightening of the fitting or locknut. 7) 90 durometer nitrile is standard for hydraulic applications. 8) See page U27. NOTE: For port tapping tools, see page S34. For assembly torques see page T5. 0.1 Return To Index
GM Inline Engines
web.statler.wvu.edutightening torques (Table 3) are at the end of the chapter. ENGINE SERIAL NUMBER ... disengage it from the drive shaft assembly. 17. Remove the engine from the boat with the ... Fill the engine with an oil recommended in Chapter Four. 12. Fill the cooling system, if equipped with a closed system. See Chapter Twelve.
RECOMMENDED ASSEMBLY TORQUES - Steelmasters
www.steelmasters.co.nzRECOMMENDED ASSEMBLY TORQUES Class 10.9 ISO Metric Coarse Pitch Bolts & Screws Bolt Tension Recommended Corresponding to Assembly 65% of Proof Load Torque kN Nm 7.67 8 10.9 13 19.8 32 31.3 63 45.5 109 62.1 174 84.5 270 103 371 132 528 164 722 190 914 248 1339 303 1817 To convert kN to lbf: Multiply kN by 224.809 To convert Nm to lbft: Multiply ...
DESIGN DRAWING STANDARDS
www.naamsstandards.orgAssembly TM GLOBAL STANDARD COMPONENTS A – 3 9. METRIC DRAWING SCALE 9.1 For general design work, drawing scales shall be full size wherever possible. 9.2 The recommended reduced scale for fixture designs are 1:2, 1:5, 1:10, 1:20 and 1:50. 9.3 When increased scales are necessary, the scales shall be 2:1, 5:1, 10:1 20:1 and 50:1.
FLENDER gear units - Siemens
cache.industry.siemens.comrecommended or approved by Siemens. The faultfree, safe operation of the products calls for proper transport, proper storage, erection, assembly, installation, startup, operation and maintenance. The permissible ambient conditions must be adhered to. Notes in the relevant documentations must be observed. Trademarks
Fastener Handout - University of Wisconsin–Madison
homepages.cae.wisc.educomponent or assembly. The feature being referenced is indicated through the use of a leader line. The leader line points to the feature in question and terminates at the note. One common example of a local note is the specification of the size dimension of a hole feature. When a callout is made to a hole feature, the leader line
HPV-02. Variable pumps for closed loop operation.
www.linde-hydraulics.comThe table shows the complete capacity range of the pumps, while the diagram below shows the recommended practical range for the different nominal sizes of the HPV-02 pump with control limit between 200 bar ∆pmin and 280 bar ∆pmax . It enables initial selection of the required nominal pump size.
Data Sheets: EPI2, Keystone (VCPDS-13139-EN)
www.emerson.comProduct Data Sheet PDS-10-04-100-3058-EN Rev. 2 September 2021 The EPI2 is an intelligent quarter-turn electric actuator designed for direct mounting to a Keystone valve. Compact and lightweight, this all-in-one actuator fits all the features of larger, heavier actuators into a neat, innovative design.