Search results with tag "High side"
NCP51530 - High and Low Side Gate Driver, High …
www.onsemi.comInput voltage range VCC −0.3 to 20 V High side boot pin voltage VB −0.3 to 720 V High side floating voltage VB−VHB −0.3 to 20 V High side drive output voltage VHO VHB – 0.3 to VB + 0.3 V Low side drive output voltage VLO −0.3 to VCC + 0.3 V Allowable hb slew rate dVHB/dt 50 V/ns Drive input voltage VLIN, VHIN −5 to VCC + 0.3 V
Active Clamp Transformer Reset: High Side or Low Side?
www.ti.comSLUA322 − September 2004 6 Active Clamp Transformer Reset: High Side or Low Side? 3 Gate Drive Considerations for Low-Side Clamp Since it has already been established that the auxiliary MOSFET of a low-side clamp circuit
PI2061- High Side High Voltage Load Disconnect Switch ...
www.vicorpower.comTitle: PI2061- High Side High Voltage Load Disconnect Switch Controller IC Author: jclarkin - Picor Subject: The PI2061 is a high-speed electronic circuit breaker controller IC designed for use with N-channel MOSFETs in high side load disconnect switch solutions for medium voltage applications.
PWM Buck Controller, Synchronous, 100V DIAGRAM
www.onsemi.com7 LDRV Output driver for low side MOSFET. 8 DRVVCC This pin provides biasing for the internal low side driver. A minimum of 0.1 F, high frequency capacitor must be connected from this pin to power ground. 9 VB This pin powers the high side driver and must be connected to a voltage higher than input voltage. A minimum of
4.5 V to 60 V Input, 2 A, 4 A, 6 A, 10 A microBUCK DC/DC ...
www.vishay.comThe SiC46x is a family of wide input voltage, high efficiency synchronous buck regulators with integrated high side and low side power MOSFETs. Its power stage is capable of supplying high continuous current at up to 2 MHz switching frequency. This regulator produces an adjustable output voltage down to 0.8 V from 4.5 V to 60 V input rail to
AN53 - Micropower High Side MOSFET Drivers
www.analog.comApplication Note 53 AN53-1 Micropower High Side MOSFET Drivers Tim Skovmand Figure 2. Logic-Level and Standard N-channel MOSFET VGS Ratings AN53 • TA02 RDS (ON) RATED AT VGS = 10V. MAX VGS = ±20V. STANDARD
MAX9611/MAX9612 - High-Side, Current-Sense Amplifiers …
datasheets.maximintegrated.com-200-100 0 100 200 300 400 500 600 700-300 0 60 8x ADC PATH T V 12-Bit ADC and Op Amp/Comparator. SENSE. SET SENSE 12-Bit ADC and Op Amp/Comparator + …
Datasheet - VN7140AJ, VN7140AS - High-side driver with ...
www.st.comSymbol Parameter Value Unit EMAX Maximum switching energy (single pulse) (TDEMAG = 0.4 ms; Tjstart = 150 °C) 10 mJ VESD Electrostatic discharge (JEDEC 22A-114F) V INPUT 4000 MultiSense 2000 SEn, SEL0,1, FaultRST OUTPUT 4000 VCC VESD Charge device model (CDM-AEC-Q100-011) 750 V Tj Junction operating temperature -40 to 150 °C Tstg Storage …
High-Accuracy, High-Side, Adjustable Current Limit Power ...
ww1.microchip.comMIC2039 High-Accuracy, High-Side, Adjustable Current Limit Power Switch General Description The MIC2039 is a highside MOSFET power distribution -
High-Accuracy, High-Side, Adjustable Current-Limit Power ...
ww1.microchip.comOct 25, 2017 · High-Accuracy, High-Side, Adjustable Current-Limit Power Switch. MIC2039 DS20005540A-page 2 2018 Microchip Technology Inc. Typical Application Circuit Functional Block Diagram MIC2039 SOT-23-6 VOUT GND VIN ILIMIT FAULT/ C1 47μF 6.3V V OUT 5V/1A V IN 5V C2 100μF 6.3V EN
Similar queries
High, Side, Voltage, High Side, Active Clamp Transformer Reset: High Side, Considerations, High Side High, High Side High Voltage Load Disconnect Switch Controller IC, Channel, Low side, Side power, Power, Current, Adjustable, High-Side, Current-Sense Amplifiers, High-side, Accuracy, High-Side, Adjustable Current, Accuracy, High-Side, Adjustable Current Limit Power Switch