1 Form A Solid-State Relay (Normally Open)

1 LH1500 AAB, LH1500 AABTR, Semiconductors Rev. , 05-Jul-20181 Document Number: 83804 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT Form A Solid-State Relay (Normally Open) DESCRIPTIONThe LH1500 is robust, ideal for telecom and ground fault applications. It is an SPST normally open switch (1 Form A) that replaces electromechanical relays in many applications. It is constructed using a GaAlAs LED for actuation control and MOSFETs for the switch output. In addition, it employs current-limiting circuitry to provide overvoltage Current limit protection Isolation test voltage 5300 VRMS Typical RON 22 Load voltage 350 V Load current 140 mA / 250 mA High surge capability Clean bounce free switching Low power consumption Material categorization: for definitions of compliance please see General telecom switching Security equipment Instrumentation Industrial controlsAGENCY APPROVALS UL1577, file no.

2 E52744S2S1 DCAC645132 ORDERING INFORMATIONLH1500###TRPART NUMBERELECTR. VARIATIONPACKAGE AND REELPACKAGEULSMD-6, tubeLH1500 AABSMD-6, tape and reelLH1500 AABTRDIP-6, mmDIP-6 SMD-6> mmLH1500 AAB, LH1500 AABTR, Semiconductors Rev. , 05-Jul-20182 Document Number: 83804 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. Functional operation of the device is not implied at these or any other conditions in excess of those given in the operational sections of this document.

3 Exposure to absolute maximum ratings for extended periods of the time can adversely affect reliabilityNotes Minimum and maximum values are testing requirements. Typical values are characteristics of the device and are the result of engineering evaluations. Typical values are for information only and are not part of the testing requirements(1)No DC mode current limit availablePIN CONFIGURATIONFig. 1 - Pin ConfigurationABSOLUTE MAXIMUM RATINGS (Tamb = 25 C, unless otherwise specified)PARAMETERCONDITIONSYMBOLVALUEU NITINPUTIRED continuous forward currentIF50mAIRED reverse voltageVR5 VInput power dissipationPdiss80mWOUTPUTDC or peak AC load voltageVL350 VContinuous load current (AC/DC configuration)IL140mAContinuous load current (DC only configuration)IL250mASSR output power dissipation (continuous) Pdiss550mWSSRA mbient temperature rangeTamb-40 to +85 CStorage temperature rangeTstg-40 to +150 CSoldering temperaturet = 10 s CELECTRICAL CHARACTERISTICS (Tamb = 25 C, unless otherwise specified)

4 PARAMETERTEST forward current, switch turn-onIL = 100 mA, t = 10 forward current, switch turn-offVL = 350 forward voltageIF = 10 (AC/DC configuration)IF = 5 mA, IL = 50 mARON-2227 On-resistance (DC only configuration)IF = 5 mA, IL = 100 Off-resistanceIF = 0 mA, VL = 100 Off-state leakage currentIF = 0 mA, VL = 100 VIO-< 1200nAIF = 0 mA, VL = 350 VIO-61000nAOutput capacitance (AC/DC configuration)IF = 0 mA, VL = 1 V, 1 MHzCO-39-pFIF = 0 mA, VL = 50 V, 1 MHzCO-6-pFCurrent limit (AC/DC configuration) (1)IF = 5 mA, t = 5 ms, VL = 6 VIlimit170300450mATRANSFERC apacitance (input to output)VISO = 1 pFAC/DC configuration6 Load ( )Load ( )Do not connect52431 ACDC only configuration6 Load (+)Load (-)52431 ACLH1500 AAB, LH1500 AABTR, Semiconductors Rev.

5 , 05-Jul-20183 Document Number: 83804 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT 2 - Timing SchematicNote As per IEC 60747-5-5, , this optocoupler is suitable for safe electrical insulation only within the safety ratings. Compliance with the safety ratings shall be ensured by means of protective circuitsSWITCHING CHARACTERISTICS (Tamb = 25 C, unless otherwise specified)PARAMETERTEST timeIF = 5 mA, IL = 50 msTurn-off timeIF = 5 mA, IL = 50 msSAFETY AND INSULATION RATINGSPARAMETERTEST CONDITIONSYMBOLVALUEUNITC limatic classificationAccording to IEC 68 part 140 / 85 / 21 Pollution degreeAccording to DIN VDE 01092 Comparative tracking indexInsulation group IIIaCTI175 Maximum rated withstanding isolation voltageAccording to UL1577, t = 1 minVISO5300 VRMSM aximum transient isolation voltageAccording to DIN EN 60747-5-5 VIOTM8000 VpeakMaximum repetitive peak isolation voltageAccording to DIN EN 60747-5-5 VIORM890 VpeakIsolation resistanceVIO = 500 V, Tamb = 25 CRIO 1012 VIO = 500 V.

6 Tamb = 100 CRIO 1011 Output safety powerPSO700mWInput safety currentISI240mASafety temperatureTS175 CCreepage distance 7mmClearance distance 7mmInsulation thicknessDTI to output test voltage, method BVIORM x = VPR, 100 % production testwith tM = 1 s, partial discharge < 5 pCVPR1669 VpeakInput to output test voltage, method AVIORM x = VPR, 100 % sample testwith tM = 10 s, partial discharge < 5 pCVPR1424 Vpeak6 OutputVL52431 ACInputOutput90 %10 %tontoffLH1500 AAB, LH1500 AABTR, Semiconductors Rev. , 05-Jul-20184 Document Number: 83804 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT 3 - Safety Power Dissipation vs.

7 Ambient TemperatureFig. 4 - Safety Input Current vs. Ambient TemperatureTYPICAL CHARACTERISTICS (Tamb = 25 C, unless otherwise specified)Fig. 5 - Maximum Load Current vs. Ambient TemperatureFig. 6 - Forward Voltage vs. Ambient TemperatureFig. 7 - Forward Current vs. Forward VoltageFig. 8 - Normalized Forward Current for Switch Turn-On Temperature0200400600800-50-250 255075100125150175 PSO-Output Safety Power (mW)Tamb- Ambient Temperature ( C)050100150200250-50-250 255075100125150175 ISI- Input Safety Current (mA)Tamb- Ambient Temperature ( C)0306090120150-40-200 20406080100IL- Load Current (mA)Tamb- Ambient Temperature ( C)IF>5 20406080100VF- Forward Voltage (V)Tamb- Ambient Temperature ( C)IF= 10 mAIF= 5 mAIF= 2 mA0102030405060 Forward Current (mA)VF- Forward Voltage (V)T = 85 CT = 25 CT = -40 C 20406080100 Normalized Forward Currentfor Switch Turn-OnTamb- Ambient Temperature ( C)Normalized to Tamb= 25 CIL= 100 mALH1500 AAB, LH1500 AABTR, Semiconductors Rev.

8 , 05-Jul-20185 Document Number: 83804 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT 9 - Normalized On-Resistance vs. Ambient TemperatureFig. 10 - Switch Capacitance vs. Applied VoltageFig. 11 - Off-State Leakage Current vs. Load VoltageFig. 12 - Turn-On Time vs. Forward CurrentFig. 13 - Normalized Turn-On Time vs. Ambient TemperatureFig. 14 - Turn-Off Time vs. Forward Current 20406080100 Normalized On-ResistanceTamb- Ambient Temperature ( C)Normalized to Tamb= 25 CIF= mAIL= 50 mA01020304050600 102030405060 Switch Capacitance (pF)Applied Voltage (V)IF= 0 mAf = 1 Leakage Current (nA)VL- Load Voltage (V)T = 85 CT = 25 CT = -40 CIF= 0 mA 1020304050 Turn-On Time (ms)IF- Forward Current (mA)T = 85 CT = 25 CT = -40 CIL= 50 mA Turn-On TimeTamb- Ambient Temperature ( C)Normalized to Tamb= 25 CIF= 5 mA 1020304050 Turn-Off Time (ms)IF- Forward Current (mA)T = 85 C T = 25 CT = -40 CIL= 50 mALH1500 AAB, LH1500 AABTR, Semiconductors Rev.

9 , 05-Jul-20186 Document Number: 83804 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT 15 - Normalized Turn-Off Time vs. Ambient Temperature PACKAGE DIMENSIONS (in millimeters)SMD-6 Turn-Off TimeTamb- Ambient Temperature ( C)Normalized to Tamb= 25 CIF= x = one footprintLH1500 AAB, LH1500 AABTR, Semiconductors Rev. , 05-Jul-20187 Document Number: 83804 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT 16 - Package DrawingsPACKAGE MARKINGFig.

10 17 - LH1500 Note Tape and reel suffix (TR) is not part of the package x = one to 9 YWW 68LH1500 AAB, LH1500 AABTR, Semiconductors Rev. , 05-Jul-20188 Document Number: 83804 For technical questions, contact: DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT INFORMATION (in millimeters)Fig. 18 - Tape and Reel PackingSOLDER PROFILESFig. 19 - Wave Soldering Double Wave ProfileAccording to J-STD-020 for DIP DevicesFig. 20 - Lead (Pb)-free Reflow Solder ProfileAccording to J-STD-020 for SMD DevicesHANDLING AND STORAGE CONDITIONSESD level: HBM class 2 Floor life: unlimitedConditions: Tamb < 30 C, RH < 60 %Moisture sensitivity level 1, according to J-STD-020 TAPE AND REEL PACKINGTYPEUNITS/REELSMD-61000 TUBE PACKINGTYPEUNITS/TUBETUBES/BOXUNITS/BOXS MD-650402000 DIP-650402000 Note: Cummulative tolerance of 10 spocket holes is Title1st line2nd line2nd lineTemperature ( C)Time (s)501502502 K/sSecondwaveFirst wave5 sFull line: typicalDotted lines:process limitsLead temperature235 C to 260 C100 C to 130 Cca.