Example: tourism industry
合金 2507 スーパー・デュープレックス・ ステンレス鋼製 …
しかしNORSOK M-001 Materials Selection standard によれば、 このチューブの最低使用温度は 46°C となっています。 NORSOK M-630 Material Data Sheets for Piping では、合金2507 ステンレス鋼チューブの肉厚が6 mm を下回る場合、低温衝撃 テストを実施する必要はありません。
Tags:
Information
Domain:
Source:
Link to this page:
Documents from same domain
Pre-Insulated Tubing Bundles - Swagelok
www.swagelok.comPre-Insulated Tubing Bundles 3 TUBING (227) BUNDLES The bundle is designed so that the jacket surface temperature will not exceed 140°F (60°C) with a process temperature of 400°F (204°C), an ambient
加熱保温バンドル・チューブ ... - swagelok.com
www.swagelok.comミリ・サイズ ① ジャケットの最高表面温度：60°C（プロセス温度204°C、周囲温度26°C、風速 16 km/h の場合） していますウレタン製ジャケットの最高表面温度：121°C
Leak Detectors, Lubricants, and Sealants (MS-01 …
www.swagelok.comLeak Detectors, Lubricants, and Sealants 3 LEAK DETECTORS LUBRICANTS SEALANTS Features Composition: Cures to a bond that resists vibration or shock Lubricates threads, preventing costly thread damage due to galling and
Grab Sampling Systems - Swagelok
www.swagelok.com• Provides a simple, effective way to safely collect samples • Keeps samples in their representative state for analysis • Can be adapted to meet system requirements
An Installer’s Pocket Guide for Swagelok Tube Fittings (MS ...
www.swagelok.comSee Swagelok tube fitting installation and reassembly, page 10 and 12 . Plugs While holding fitting body steady, tighten the plug one-quarter turn from the finger-tight position . For 1/16, 1/8, and 3/16 in.; 2, 3, and 4 mm tube fittings, tighten the plug one-eighth turn.
Hand Tube Bender Manual (MS-13-43;rev 5;en-US ... - …
www.swagelok.comHand Tube Bender Manual www.swagelok.com. 2. 3 Contents ... Read this manual before using the hand tube bender . Tubing Data The Swagelok hand tube bender bends 1/8, 1/4, 5/16, 3/8, and 1/2 in ., and 3, 6, 8, 10, and 12 ... when bending softer tubing such as copper or aluminum .
Ball Valves, General Purpose and Special Application 60 ...
www.swagelok.com• Swagelok ball valves are designed to be operated in ... (2-way) design. The one-piece center body uses no welding and allows 180° actuation. The switching design allows the user to: divert flow from a common inlet to one of two outlets ... Every 60 series ball valve is …
One-Piece Instrumentation Ball Valves - Swagelok
www.swagelok.comOne-piece ball stem ensures alignment of stem and orifice. 40T and 40E Series for Low-Temperature Service SW ... One-Piece Instrumentation Ball Valves—40G Series and 40 Series 5 40G / 40 SERIES BALL ... The 40G series valve is designed for thermal cycling …
Pressure Regulators K Series - Swagelok
www.swagelok.comPressure Regulators K Series Pressure-reducing models Back-pressure models Gas cylinder changeover model Vaporizing models www.swagelok.com. 2 Pressure Regulators and Filters K SERIES REGULATORS ... High-Pressure (KPP Series), 16 High-Flow (KPF Series), 18 High-Pressure
Trunnion Ball Valves - Swagelok
www.swagelok.comTrunnion Ball Valves—83 Series and H83 Series 1 83 / H83 SERIES BALL Trunnion Ball Valves 83 Series and H83 Series Working pressures up to 10 000 psig (689 bar) 1/8 to 1/2 in. and 6 to 12 mm Swagelok® tube fitting or NPT end connections 316 stainless steel materials www.swagelok.com
Related documents
Technical Data Sheet - Jotun
www.jotun.comNORSOK Standard M-501, Edition 6, Coating system no. 7A - Carbon and stainless steel in the splash zone NORSOK Standard M-501, Edition 6, Coating system no. 7B - Submerged carbon and stainless steel ≤ 50 °C NORSOK Standard M-501, Edition 6, Coating system no. 7C - Submerged carbon and stainless steel >50 °C Colours selected range of colours
ASTM A182 F51 – Duplex Stainless Steel
www.duplexsteel.coNORSOK D41 to D45 Forging Forging temperature for this material should be 1100 – 1250oC Reheat as often as necessary and cool in still air. Machining Material in the annealed condition is readily machinable by all conventional methods. Welding F51 is readily weldable using many of the standard electric arc welding processes but oxyacetylene ...
NORSOK STANDARD N-001
www.standard.noNORSOK standard N-001 Rev. 4, February 2004 NORSOK standard Page 4 of 22 NORSOK N-002 Collection of metocean data NORSOK N-003 Actions and action effects NORSOK N-004 Design of steel structures NORSOK N-005 Condition monitoring of load bearing structures NORSOK S-001 Technical safety NORSOK S-002 Working environment
NORSOK STANDARD
www.standard.noNORSOK Standard 2 of 16 FOREWORD NORSOK (The competitive standing of the Norwegian offshore sector) is the industry initiative to add value, reduce cost and lead time and remove unnecessary activities in offshore field developments and operations. The NORSOK standards are developed by the Norwegian petroleum industry as a part of the
ISO12944 - AkzoNobel
international.brand.akzonobel.comISO12944 is the industry standard for corrosion protection of steel structures by protective paint systems. Originally released in 1998, the standard is put together by representatives from key countries and companies involved in the protection of steel structures to build a mutually beneficial standard.
Gas-Liquid Separators Sizing Parameter
www.jmcampbell.comSep 09, 2015 · region is NORSOK P-100. Table 1. API 12 J recommended range of KS –values for vertical and horizontal separators [7] Type Height or Length, ft (m) Typical KS range, ft/sec Typical KS range, m/s Vertical 5 (1.52) 0.12 to 0.24 0.037 – 0.073 10 (3.05) 0.18 to 0.35 0.055 – 0.107 Horizontal 10 (3.05) 0.40 to 0.50 0.122 to 0.152