3M Scotchkote Rebar Liquid Patch Compound …

1 Pot Life [60 g ( lbs) quantity33M Scotchkote Rebar Liquid Patch Compound413/215 and Cold Weather Grade 413/215 Instruction SheetProduct Description3M Scotchkote Rebar Liquid Patch Compound 413/215 and Cold Weather Grade 413/215 are two-part, ambient temperature cure, high solids content, thermosetting, Liquid epoxy coatings. They are designed for the repair of scrapes, scars, damage or imperfections in 3M Scotchkote Fusion-Bonded Epoxy Coating 413/215 and 413/215 Spray Grade. Meets ASTM A 775/A 775M, ASTM D 3963, AASHTO M 284-81 and AASHTO M for UseThe mixing ratio of Scotchkote 413/215 and Cold Weather Grade 413/215 is one part A to one part B by volume.]

2 Combine the two parts and mix thoroughly until a uniform color is obtained. If the components are mixed in an incorrect proportion, or the components are not thoroughly mixed, the coating will not cure properly and will remain tacky. The coating may be applied immediately after mixing. Multiple applications maybe required to meet edge coverage. If necessary, a second coat can be applied once the first coat is tack pot life of the combined material depends on temperature. Use the pot life graph below as a guideline. Prepare only the quantity of coating that can be applied in the indicated period of time. For minor damage or repair of Scotchkote Fusion Bonded Epoxy Coating 413 apply Scotchkote 413/215 as follows: 1) Remove moisture.

3 2) Clean all oil, grease, dust, scale, rust and damaged coating from the area to be repaired. 3) Mix A and B components thoroughly before combining. Apply Scotchkote 413/215 by standard spray or airless spray equipment, brush, or roller. To achieve maximum coating thickness, Scotchkote Patch compounds SHOULD NOT be thinned. To spray the Patch Compound use minimum in ( mm) tip orifice opening and a dry, oil free air supply capable of continuously supplying at least 20 cfm ( m3/min) at 40 psi ( bar) to the gun nozzle. 4) Allow applied coating to dry prior to handling and storage. For best results, use Scotchkote 413/215 when the temperature is 50 F (10 C) or higher during application and cure.

4 Minimum recommended coating thickness is 5 mils. Minimum application temperature is 40 F (4 C). For best results, use Scotchkote 413/215 CWG when the temperature is 15 F (-9 C) or higher during application and cure. Minimum application temperature is 5 F (-15 C). More than one coat/application of product may be needed to meet minimum edge coverage Patch Compound 413/215 Scotchkote Patch Compound CWG 413/215 Scotchkote Patch Compound CWG 413/215 Pot Life [60 g ( lbs) quantityScotchkote Patch Compound 413/2153 Infrastructure Protection Division6801 River Place , TX recycle. Printed in USA. 3M 2012. All rights and Safety PrecautionsRead all Health Hazard, Precautionary and First Aid, Material Safety Data Sheet, and/or product label prior to handling or Information/Customer ServiceFor ordering technical or product information, or a copy of the Material Safety Data Sheet, call:Phone: 800/722-6721 Fax.]

5 877/601-1305 Typical Properties3M Scotchkote Patch Compound 413/2153M Scotchkote Cold WeatherGrade Patch Compound 413/215 PropertyValuesColorLight Green - color matched toScotchkote 413/215 Light Green - color matched toScotchkote 413/215 Dry Film Coverage without waste120 ft2/lb/mil109 ft2/lb/milViscosity/Mixed95 - 98 - 100 Life unmixed, unopened containers24 months24 monthsPot LifeSee graphSee graphDrying TimeSee graphSee graphClosed Cup Flash PointPart A 98 F (36 C)Part B 140 F (60 C)Part A 125 F (52 C)Part B 112 F (44 C)Mix Ratio1:1 by volume; to 1B by weight1:1 by volume; to 1B by weightSag (mil)0 @120 @12 VOC (g/L)271112 Solids by by volumeUnit Weight2 gal unit ( L) 20 lbs ( kg)1/2 gal unit ( L) 5 lbs ( kg) 1 pint unit ( L) lbs (567 g)55 gal Drum (208L) 1079 lbs (489 kg)1 pint unit (0,47 L) lbs (621 kg)3M and Scotchkote are trademarks of 3M NoticeAll statements, technical information and recommendations related to 3M Products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed.

6 Before using the 3M Product, you must evaluate it and determine if it is suitable for your intended application. Because conditions of Product use are outside of our control and vary widely you assume all risks and liability associated with such use. Any Product-related statements not contained in current 3M publications, or any contrary statements contained in your purchase order, shall have no force or effect unless expressly agreed to in writing by an authorized officer of ; Limited Remedy; Limited Liability. 3M warrants that Product will conform to 3M published specifications upon shipment. If Product is proven not to have met the specifications your exclusive remedy and 3M s sole obligation will be, at 3M s option, to replace the Product or to refund the purchase price of the Product.

7 EXCEPT WHERE PROHIBITED BY LAW, THIS WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR THOSE ARISING FROM A COURSE OF DEALING, CUSTOM OR USAGE OF TRADE. Buyer is an expert in its field and is responsible for determining if Products are suitable for a particular purpose or application. 3M has no obligation under this warranty with respect to any Product that has failed due to inadequate or improper storage, handling, surface preparation, application, or maintenance; failure to follow Product instructions; or alteration or damage to the Product caused by accident, neglect, or misuse.

8 EXCEPT WHERE PROHIBITED BY LAW, IN NO EVENT SHALL 3M BE LIABLE FOR ANY DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL LOSS OR DAMAGES (INCLUDING LOST PROFITS) ARISING FROM THIS PRODUCT, REGARDLESS OF THE LEGAL THEORY ASSERTED.