63230-401-203A1

1 PowerLogic Power Meter PM5350. User Guide 63230-401-203A1 . 03/2011. HAZARD CATEGORIES AND SPECIAL SYMBOLS. Read these instructions carefully and look at the equipment to become familiar with the device before trying to install, operate, service or maintain it. The following special messages may appear throughout this bulletin or on the equipment to warn of potential hazards or to call attention to information that clarifies or simplifies a procedure. The addition of either symbol to a Danger or Warning safety label indicates that an electrical hazard exists which will result in personal injury if the instructions are not followed.

2 This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. DANGER. DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. WARNING. WARNING indicates a potentially hazardous situation which, if not avoided, can result in death or serious injury. CAUTION. CAUTION indicates a potentially hazardous situation which, if not avoided, can result in minor or moderate injury. CAUTION. CAUTION, used without the safety alert symbol, indicates a potentially hazardous situation which, if not avoided, can result in property damage.

3 NOTE: Provides additional information to clarify or simplify a procedure. PLEASE NOTE. Electrical equipment should be installed, operated, serviced, and maintained only by qualified personnel. No responsibility is assumed by Schneider Electric for any consequences arising out of the use of this material. CLASS A FCC STATEMENT. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

4 This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. This Class A. digital apparatus complies with Canadian ICES-003. 63230-401-203A1 PowerLogic Power Meter PM5350. 03/2011 Table of Contents Table of Contents Chapter 1: Introduction Power Meter Hardware .. 1. Power Meter Parts and Accessories.

5 2. Box Contents .. 2. Firmware .. 2. Chapter 2: Safety Before You Begin .. 3. Precautions Chapter 3: Operation Operating the Display .. 5. How the Buttons Work .. 6. Changing Values .. 6. Icons .. 7. LEDs .. 7. Energy/Alarm 7. Heartbeat/Comms LED .. 7. Menu Overview .. 9. Setting Up the Power Meter .. 10. Power Meter Basic Setup .. 10. Setting Up the Power System .. 10. Supported Power System 11. Setting Up Voltage Connection and CT Options .. 13. Setting Up the System Frequency .. 14. Setting Up the Phase Rotation .. 14. Power Meter Advanced Setup .. 15. Setting Up the Load Timer Setpoint .. 15. Setting Up the Peak Current Demand Over Last Year.

6 16. Power Meter Demand Setup .. 16. Setting Up Power and Current Demand .. 17. Select the Digital Input .. 18. Power Meter Comms Setup .. 19. Setting Up Communications .. 19. Setting Up Alarms .. 19. Setting Up I/O .. 20. Power Meter HMI Setup .. 20. Setting Up the Display .. 20. Setting Up Regional Settings .. 22. Setting Up Passwords .. 23. Power Meter Clock Setup .. 23. Setting Up the Clock .. 24. Reset the Power Meter .. 24. Global Resets .. 25. Single Resets .. 26. Chapter 4: Metering Power Meter Characteristics .. 27. MODBUS RS485 .. 28. Digital Outputs .. 28. Digital Inputs .. 28. Min/Max Values for Real-Time Readings.

7 28. Power Factor Min/Max Conventions .. 29. Demand Readings .. 30. Demand Calculation Methods .. 30. Block Interval Demand .. 30. Synchronized Demand .. 32. Thermal 33. Predicted Demand .. 33. Peak Demand .. 34. Energy Readings .. 34. Power Analysis Values .. 35. 2011 Schneider Electric All Rights Reserved i PowerLogic Power Meter PM5350 63230-401-203A1 . Table of Contents 03/2011. Chapter 5: Alarms About Alarms .. 37. 1-Second Alarms .. 37. Digital Alarms .. 39. Unary Alarms .. 40. Alarm Priorities .. 40. Using an Alarm to Control a Relay Output .. 40. Alarm Setup .. 40. Setting Up 1-Second Alarms .. 41.

8 Setting Up Unary Alarms .. 43. Setting Up Digital Alarms .. 44. Viewing Alarm Activity and History .. 46. Viewing Active Alarms and Alarm Counters .. 46. Viewing Unacknowledged Alarms and the Alarm History Log .. 47. Chapter 6: Input/Output Digital Inputs .. 49. Capabilities Setting Up the Digital Inputs .. 50. Setting Up the Digital Inputs in Normal Mode .. 51. Setting Up the Digital Inputs in Demand Sync Mode .. 52. Digital Outputs .. 53. Setting Up the Digital Output .. 54. Setting Up the Digital Output in External Mode .. 55. Setting Up the Digital Output in Alarm Mode .. 56. Setting Up the Digital Output in Demand Sync Mode.

9 57. Energy/Alarm LED .. 58. Setting Up the Energy/Alarm LED .. 58. Chapter 7: Maintenance and Password Recovery .. 59. Troubleshooting Power Meter Memory .. 59. Identifying the Firmware Version, Model, and Serial Number .. 59. Additional Meter Status Information .. 60. 60. Control Power .. 60. Downloading Firmware .. 60. Troubleshooting .. 61. Heartbeat/Comms LED .. 61. Getting Technical Support .. 62. Register List .. 62. Appendix A: Specifications Power Meter Specifications .. 63. Appendix B: Communications Communications Capabilities .. 67. Wiring Daisy-Chaining Devices to the Power Meter .. 67. Appendix C: Power Factor Power Factor Register Format.

10 69. Register Format Appendix D: Command Command Interface .. 71. Interface Using the Protected Command Interface .. 72. Using the Unprotected Command Interface .. 73. Glossary Terms .. 75. Abbreviations .. 77. Index .. 79. ii 2011 Schneider Electric All Rights Reserved 63230-401-203A1 PowerLogic Power Meter PM5350. 03/2011 Power Meter Hardware Chapter 1 Introduction Power Meter Hardware Figure 1 1 below shows the parts of the power meter. Table 1 1 describes the parts. Figure 1 1 Parts of the power meter (rear view). B C. A. G. D E F. Table 1 1 Parts of the Power Meter Number Part Description A Retainer clips Used to secure the power meter in place Control power supply B Connection for control power to the power meter connector C Voltage inputs Voltage metering connections D Digital outputs Digital outputs (DO1 and DO2) connections Used for communications with a monitoring and control system, can E RS485 port (COM1).