6500 quickfix 201510 - SealBoss

1 SealBoss Product Data Sheet 6500 quickfix Polyurea Joint Filler Product Description Fast Cure Joint Filler & Joint Repair System SealBoss 6500 quickfix is a technologically advanced Clear, Grey and Custom Colors self leveling, two component, 1:1 ratio, 100% solids, flexible polyurea elastomer product. SealBoss 6500 quickfix Applications SealBoss 6500 quickfix is a high quality joint and crack filler To fill cracks, damaged control joints, for concrete substrates in applications that are time critical. It works well in adverse temperature conditions as the material construction joints on horizontal concrete cures in ambient temperatures from -28C (-20F) to 54C For industrial floor applications which receive (130F).

2 The tack free time is 5 to over 15 minutes depending heavy vehicle tra c, such as fork lifts or steel on temperature. This permits to reopen the jobsite to vehicle wheeled carts and foot tra c just one hour after the application. Exposure to Highly flexible, allowing slab movement, sunlight (UV) may cause discoloration, however the physical yet strong enough to protect the vertical edges properties are essentially una ected. Ask your SealBoss of concrete from spalling under heavy loading technician for details. The product is for professional use. Interior and exterior use, discoloration in prolonged UV exposure in lighter colors Installation Guidelines Clean the area of debris and contaminants, such as oils, Advantages loose materials, dirt, rubber etc.

3 , to allow for good adhesion of the product. Expose clean rough concrete for best results. 100% Solids and VOC Free If using a saw to cut concrete and clean the crack, remove Remains Flexible, Even in Cold Temperatures all the dust from the cut out area. Make sure the area is dry. Return Project to Service in 60 Minutes All equipment, pumps and hoses must be dry. Avoid moisture Cures From -28C / -20F to 54C / 130F. contact with the mixture. Reduced Moisture Sensitivity Essentially Odorless For bulk mixing, pre-mix each component thoroughly. Proportion Resistant to Petrochemicals equal parts by volume of Component A and Component B.

4 Through appropriate metered mixing equipment. Mix only the quantity that can be used within 2 minutes and do not allow Typical Application Environments mixed material to reside in static mixing head or mixer for more than 1 minute or nozzle blockage may result. Industrial Facilities Do not add solvents. They will prevent proper cure. Not for Warehouse Floors sealing cracks and joints under hydrostatic pressure or with Manufacturing Facilities extreme movement. Material is a vapor barrier after cure. Pulp and Paper Mills Minimum age of concrete must be 21-28 days, depending on Bottling and Canning Facilities curing and drying conditions prior to applications.

5 Airports Water and Waste Water Treatment Maintenance of Equipment SealBoss 6500 quickfix Polyurea Joint Filler Cold Storage Facilities Tools and equipment must be cleaned immediately after use. Food Processing Facilities Remove all excess product. Cured product is hard to remove. Freezers SealBoss R70 Pump Flush is a solvent free, non-flammable cleaner, lubricator, pump and hose conditioner. Please refer to Tips for Cartridge Users the product data sheet for detailed information. Shake cartridge prior to all applications and each Health and Safety time it is used for a minimum of 1 minute.

6 Remove air from system - prime cartridge by slowly Protect your health! Always use safety gear in compliance with dispensing product from cartridge into mixer in OSHA and all applicable local and job-site regulations While vertical orientation until mixer is completely filled. working with products. Handling of this product may result in spills, splashes, and airborne substances. Wear appropriate Discard a small amount of product prior to safety goggles, gloves and safety clothing at all times. Consider application. Ratio may be slightly o when initial property in proximity of the application to prevent loss or product travels through static mixer.

7 Once uniform damage. Protect jobsite from unauthorized persons. Store all mixture is observed, product is ready for application. materials and equipment safely and out of reach of children and Do not apply to wet or damp substrates. animals! Observe container labels, SDS, applicable laws and Excessive moisture may cause bubbles or regulations and all instructions before using the product and uneven reaction. equipment. In case one of the components comes in contact with the skin, wash thoroughly with soap and water. Provide Recommended Joint Filler Pump adequate ventilation in volume and pattern in working area.

8 Further protection: emergency showers and eyewash stations. Get immediate medical attention as needed. JointMaster Pro2 G3i Digital SealBoss Corp. USA ph 877-932-2293 intl 714-662-4445. SealBoss Product Data Sheet 6500 quickfix Polyurea Joint Filler TECHNICAL DATA. PHYSICAL PROPERTIES: Color (A+B) Charcoal Grey, Black, or other Viscosity (mixed) Self Leveling Mix Ratio (by volume) 1:1. Pot Life at 25C / 77F 30 - 60 sec Standard Tack Free , Thin Film at 25C / 77F 5-8 min Initial Cure at 25C / 77F 15 min Final Cure at 25C / 77F 60 min % of Elongation 180-200 ASTM D-412. Service Movement 20%.

9 Tensile Strength, psi 900-1000 ASTM D-412. Bond Strength, fully cured clean concrete, psi 500 ASTM C-882. Shore A Hardness 75-85A ASTM D-2240. Resistance to Chemicals Resistant to Most Organic Solvents, Mild Acids, Alkali and Micro Organisms PACKAGING: 1:1 ratio by volume units: 22/44/56 oz. Cartridges, 22oz. cartridge yields 39 cu. in. 2 gal. Units, 10 gal. Units Shelf Life: 1 year in original unopened container. Storage Conditions: Store at 55F-95 F. Disposal: In accordance with all applicable laws and regulations. Empty containers must be drip free Chemical Resistance: Test Procedure; ASTM D-1308 R=Recommend Material Consumption RC=Recommend Conditional, some swelling Filling joint slots in given dimensions.

10 Feet per 22 oz. Cartridge or discoloration N=Not Recommend Width 1/4" 1/2" 3/4" 1" 1-1/4" 1-1/2". 1=Some discoloration only Depth Chemical Result 1/4" Acetic Acid 10 % R 1/2" Acetone RC 3/4" Battery Acid (Sulfuric Acid) RC 1" Brake fluid R 1- 1/4" Chlorine (2,000ppm in H2O) R 1-1/2" Citric Acid R 1-3/4" Gasoline R 2" Hydraulic Oil R-1 2-1/2" .87. Methanol (5%) Gasoline RC 3" .87 .73. Motor Oil R-1. Toluene RC. Vinegar R. Water R. Xylene R. SealBoss 6500 quickfix Polyurea Joint Filler JointMaster Pro2 G3i Digital Two Component Joint Filler Pump Limited Warranty Policy and Disclaimer for Products Supplied and/or Distributed by SealBoss Corp.