Advant OCS $GYDQW &RQWUR OOHU

1 Advant OCSwith Master software $GYDQW &RQWUROOHU User s Guide 3 BSE 002 415R701 Rev A 3 BSE 002 415R701 Rev A 3 BSE001264/ETemplate: 3 BSE001286/EUse of '$1*(5, :$51,1*, &$87,21, and 127(This publication includes, '$1*(5, :$51,1*, &$87,21, and 127( information where appropriate to point out safety related or other important information.'$1*(5 Hazards which could result in severe personal injury or death:$51,1*Hazards which could result in personal injury&$87,21 Hazards which could result in equipment or property damage127(Alerts user to pertinent facts and '$1*(5 and :$51,1* hazards are related to personal injury, and &$87,21 hazards are associated with equipment or property damage, it should be understood that operation of damaged equipment could, under certain operational conditions, result in degraded process performance leading to personal injury or death.)))))))

2 Therefore, comply fully with all '$1*(5, :$51,1*, and &$87,21 $'(0$ , AdvaBuild, Advant Controller, Advant Fieldbus, Advant Station, MasterBatch, MasterGate, MasterBus, MasterFieldbus, ABB Master, ABB MasterNet, ABB MasterPiece and ABB MasterView registered trademarks of ABB Asea Brown Boveri Ltd. is a trademark of Allan-Bradley is a trademark of Microsoft is a registered trademark of Epson is a trademark of Rosemount Safeguard is a trademark of ABB Industri AS, Tally is a trademark of Mannesmann Tally 68040 is a registered trademark of MOTOROLA is a registered trademark of Gould is a trademark of the international organization PROFIBUS INTERNATIONAL (PI).))

3 Echelon, LON, LonTalk, LONWORKS, and Neuron are registered trademarks of Echelon and all Siemens-products mentioned in this publication are trademarks of Siemens is a trademark of ABB Industri AS, is a trademark of Digital Equipment ,&(The information in this document is subject to change without notice and should not be construed as a commitment by ABB Automation Products AB. ABB Automation Products AB assumes no responsibility for any errors that may appear in this no event shall ABB Automation Products AB be liable for direct, indirect, special, incidental or consequential damages of any nature or kind arising from the use of this document, nor shall ABB Automation Products AB be liable for incidental or consequential damages arising from use of any software or hardware described in this document and parts thereof must not be reproduced or copied without ABB Automation Products AB s written permission.)

4 And the contents thereof must not be imparted to a third party nor be used for any unauthorized purpose. The software described in this document is furnished under a license and may be used, copied, or disclosed only in accordance with the terms of such ( 0$5.,1*This product meets the requirements specified in EMC Directive 89/336/EEC and in Low Voltage Directive 73/23 ABB Automation Products AB Controller 450 User s GuideTable of Contents3 BSE 002 415R701 Rev A iTABLE OF CONTENTSC hapter 1 - Organization .. History .. Overview .. Versions .. Designation .. Structure .. System Utilities .. Module Contents.)

5 Clock, External Clock Synchronization .. Module .. Supply .. Interface .. I/O .. I/O .. I/O .. Link Types .. Communication .. Control .. Language .. of Application Building .. s Interface .. Personnel .. Operator .. and Security .. 1-106 Advant Controller 450 User s Guide Table of Contentsii3 BSE 002 415R701 Rev A .. Carrier and Submodule .. Interface .. 1-124 Chapter 2 - Planning Environment .. Selection and Building Considerations .. Compatibility .. of CE-marking Layout and Disposition of .. Supply and Connection .. Principles, Fusing and Voltage Distribution Applications.

6 Voltage Switch-gear Applications .. Stroke Protection .. and Mounting and Storing .. Regulations .. and Process Safety .. Safety .. and the .. Earth .. Line .. of Process Cable Shields .. of Communication Cable Shields .. of Internal System Cable Shields, Connection Unit -- I/O 2-24 Advant Controller 450 User s GuideTable of Contents3 BSE 002 415R701 Rev A of Process Signals .. of Additional Equipment .. Conductors .. Routing in Cabinets .. Supply Connection .. for .. Extension to S100 I/O .. I/O and S400 Units .. Philosophy, Earthing Line Cabling, Shielding, Grounding, Maximum.

7 Protection .. , Connection Unit, Circuit Board .. , Internal Cables .. Cables .. , Communication Cables .. Procedures Before Procedures .. Regulations .. and I/O .. Equipment .. Regulations .. and I/O .. of Engineering Station .. System Configuration .. 2-57 Advant Controller 450 User s Guide Table of Contentsiv3 BSE 002 415R701 Rev A and Loading .. of the Controller Start-up and Verification of the Start .. of Battery for Backup of Memory .. Verification .. Regulations .. Tool .. Permission .. and Deblocking of the PC Program .. of some Test Facilities provided by the Engineering Station.

8 Of Feedback Control of PC Programming During Operation when of Executing Unit Status .. of Process Input/Output of PC Program and Data Control .. of Functions in Systems Already Operating .. Tool .. Regulations .. I/O Boards .. with Redundant Processor Module .. of the System Software .. Ahead of Program Loading .. 2-91 Chapter 3 - Configuration/Application Considerations .. System Utilities .. Supervisory 3-3 Advant Controller 450 User s GuideTable of Contents3 BSE 002 415R701 Rev A of Application Program .. Supply .. Interface .. I/O System .. I/O System.

9 I/O System .. Link Types .. Communication .. Control .. Building with s Interface .. Operator .. and Security .. Dissipation Permitted in Cabinets .. in Groups .. of Heat Generated in a and Repair .. Possibilities and Spare Considerations .. Calculation .. , Load Calculation .. Data Including Capacity & Performance .. System Utilities .. Processor Modules .. Clock .. Supply .. Interface .. Technical Data, Capacity .. I/O .. I/O .. I/O .. Link Types .. 3-65 Advant Controller 450 User s Guide Table of Contentsvi3 BSE 002 415R701 Rev A Communication .. Control.

10 S Interface .. Operator Station .. Operator .. Start-up .. to the Definition .. Procedures .. Building Menus .. 3-76 Chapter 4 - Runtime Operation .. Modes .. Working Modes .. and Backup Processor Module .. between Start Modes and Working Modes .. Power-up .. and Initialization of Controller which Contains Application .. between Engineering Station Commands and WorkingModes .. Program .. System .. Communication .. for the System Program .. Program .. Area for PC Programs .. 4-20 Advant Controller 450 User s GuideTable of Contents3 BSE 002 415R701 Rev A Program.