AIR CONDITIONER OUTDOOR UNIT - Fujitsu General

1 EnglishFran aisEspa olEn-1 AIR CONDITIONER OUTDOOR UNITPART NO. 9374747115 INSTALLATION MANUALFor authorized personnel D'INSTALLATIONPour le personnel agr DE INSTALACI NSolo para personal 120/12/2553 8:58:37En-1 SAFETY PRECAUTIONS11 This installation manual describes how to install the OUTDOOR unit only. To install the indoor unit , refer to the installation manual included with the indoor !Please Read Before StartingThis air conditioning system meets strict safety and operating the installer or service person, it is an important part of your job to install or service the system so it operates safely and safe installation and trouble-free operation, you must: Carefully read this instruction booklet before beginning.

2 Follow each installation or repair step exactly as shown. Observe all local, state, and national electrical codes. Pay close attention to all danger, warning, and caution notices given in this :This mark indicates procedures which, if improperly performed, are most likely to result in the death or serious injury to the user or service :This symbol refers to a hazard or unsafe practice which can result in severe personal injury or :This symbol refers to a hazard or unsafe practice which can result in personal injury and the potential for product or property damage. Hazard alerting symbolsElectricalSafety / alertIf Necessary, Get HelpThese instructions are all you need for most installation sites and maintenance conditions.

3 If you require help for a special problem, contact our sales/service outlet or your certified dealer for additional Case of Improper InstallationThe manufacturer shall in no way be responsible for improper installation or maintenance service, including failure to follow the instructions in this PRECAUTIONS When Wiring ELECTRICAL SHOCK CAN CAUSE SEVERE PERSONAL INJURY OR DEATH1 ONLY A QUALIFIED, EXPERIENCED ELECTRICIAN SHOULD ATTEMPT TO WIRE THIS SYSTEM1 Do not supply power to the unit until all wiring and tubing are completed or reconnected and checked.

4 Highly dangerous electrical voltages are used in this system. Carefully refer to the wiring diagram and these instructions when wiring. Improper connections and inadequate grounding can cause accidental injury or death. Ground the unit following local electrical codes. Connect all wiring tightly. Loose wiring may cause overheating at connection points and a possible fire Transporting Be careful when picking up and moving the indoor and OUTDOOR units. Get a partner to help, and bend your knees when lifting to reduce strain on your back. Sharp edges or thin aluminum fins on the air CONDITIONER can cut your Installing111.

5 In a Ceiling or WallMake sure the ceiling/wall is strong enough to hold the unit s weight. It may be necessary to construct a strong wood or metal frame to provide added a RoomProperly insulate any tubing run inside a room to prevent sweating that can cause dripping and water damage to walls and Moist or Uneven LocationsUse a raised concrete pad or concrete blocks to provide a solid, level foundation for the OUTDOOR unit . This prevents water damage and abnormal an Area with High WindsSecurely anchor the OUTDOOR unit down with bolts and a metal frame. Provide a suitable air a Snowy Area (for Heat Pump-type Systems)Install the OUTDOOR unit on a raised support that is higher than drifting snow.

6 Provide snow Connecting Refrigerant Tubing Keep all tubing runs as short as possible. Use the flare method for connecting tubing. Apply refrigeration compressor oil (or equivalent) used for the OUTDOOR unit to the matching surfaces of the flare and union tubes before connecting them, then tighten the nut with a torque wrench for a leak-free connection. Check carefully for leaks before starting the test :Depending on the system type, liquid and gas lines may be either narrow or wide. Therefore, to avoid confusion the refrigerant tubing for your particular model is specified as either small or large rather than as liquid or gas.

7 When Servicing Turn the power OFF at the main circuit breaker panel before opening the unit to check or repair electrical parts and wiring. Keep your fingers and clothing away from any moving parts. Clean up the site after you finish, remembering to check that no metal scraps or bits of wiring have been left inside the unit being serviced. After installation, explain correct operation to the customer, using the operating sure to read this Manual thoroughly before installation. The warnings and precautions indicated in this Manual contain important information pertaining to your safety.

8 Be sure to observe this Manual, together with the Operating Manual, to the customer. Request the customer to keep them on hand for future use, such as for relocating or repairing the installation, explain correct operation to the customer, using the operating manual. DANGERN ever touch electrical components immediately after the power supply has been turned off. Electrical shock may occur. After turning off the power , always wait 5 minutes or more before touching electrical components. WARNINGD uring installation, make sure that the refrigerant pipe is attached firmly before you run the compressor. Do not operate the compressor under the condition of refrigerant piping not attached properly with 2-way or 3-way valve open.

9 This may cause abnormal pressure in the refrigeration cycle that leads to breakage and even not remove the connection pipe while the compressor is in operation with 2-way or 3-way valve open. This may cause abnormal pressure in the refrigeration cycle that leads to breakage and even installing and relocating the air CONDITIONER , do not mix gases other than the specified refrigerant (R410A) to enter the refrigerant cycle. If air or other gas enters the refrigerant cycle, the pressure inside the cycle will rise to an abnormally high valueand cause breakage, injury, installing this system in high humidity locations, install using ground fault equipment breakers (often referred to in other countries as an ELCB earth leakage current breaker) to reduce the risk of leaking current which may result in electric shock or potential MANUALPART NO.

10 9374747115 Contents1. SAFETY PRECAUTIONS ..12. ABOUT THE Precautions for using R410A refrigerant .. Special tools for R410A .. Accessories .. System configuration ..33. INSTALLATION Selecting an installation location .. Drain installation .. Installation dimensions .. Transportation of the unit .. Installation of the unit ..64. PIPE Flare connection (pipe connection) ..65. ELECTRICAL The precautions of electrical wiring .. Electrical requirement .. unit wiring .. Connection Diagrams .. OUTDOOR unit ..96. PIPE Vacuum .. Additional charging ..107. power ..108. TEST Make a test run in accordance with the installation instruction sheet for the indoor unit .