AS4586-2013 Flowcoat CR (0.3mm)

1 Technical Profile FIRE RESISTANCE. EN 13505-1 BFL - s1. SLIP RESISTANCE. Method described in Dry & Wet Rating is AS4586-2013 dependant on specification (in accordance with AS4586-2013 ). The slipperiness of flooring materials can change significantly, due to Flowcoat CR ( ) the installation process, after short periods of use, due to inappropriate maintenance, longer-term wear and/or surface contaminants (wet or dry). Textured systems are recommended to meet slip resistance value requirements for wet conditions and/or surface contaminants (wet or dry) - please contact our Technical Advisors for further details High performance, solvent free, TEMPERATURE RESISTANCE.

2 Hard wearing epoxy resin coating Tolerant up to 60 C. which provides enhanced chemical WATER PERMEABILITY. resistance. Karsten Test Nil (Impermeable). SURFACE HARDNESS. Typically used in industrial environments which Koenig Hardness Test 180secs may be subjected to chemical spillages. BOND STRENGTH. ASTM D4541 (Pull-Off Test) > *. ABRASION RESISTANCE. Taber Abrader BS8204-2 80mg loss per 1000 cycles 1kg load using CS10 wheels COMPRESSIVE STRENGTH. BS6319 >60 N/mm . FLEXURAL STRENGTH. BS6319 >40 N/mm . TENSILE STRENGTH. BS6319 >15 N/mm . chemical RESISTANCE. Contact Technical Department SPEED OF CURE** 10 C 20 C 30 C.

3 Light Traffic 48 hrs 24 hrs 16 hrs Full Traffic 72 hrs 48 hrs 36 hrs Solvent Free & Low Odour: Full chemical Cure 12 days 7 days 6 days The coating is low in odour and These figures are typical properties achieved in laboratory tests at 20 C and at solvent free. 50% Relative Humidity. *Assume concrete or substrate is a minimum of 25 N/mm . chemical Resistant: Provides enhanced resistance against a range of chemicals. Low Maintenance: Seamless, hygienic finish, which Light N Grey Steel Grey Charcoal Tile Red requires low maintenance. Version Durable: Hard wearing, durable and abrasion Light Green Dark Green Steel Blue Mid Blue resistant.

4 The applied colours may differ from the examples shown. For a full colour chart and samples, contact your local Flowcrete office. Model Specification Installation Service System Flowcoat CR The installation should be carried out by a qualified contractor with a documented Finish Gloss quality assurance scheme. For details of Thickness our recommended contractors, contact your Manufacturer Flowcrete Australia Pty Ltd local Flowcrete office. Detailed application Contact + 61 7 3205 7115 instructions are available upon request. Environmental Considerations Preparatory work and application in accordance with manufacturer's instructions.

5 The finished system is assessed as non- hazardous to health and the environment. System Design The long service life and seamless surface reduce the need for repairs and Flowcoat CR maintenance. Environmental and health considerations are controlled during manufacture of the products by Flowcrete staff. Aftercare, Cleaning & Maintenance Clean regularly using a single or double Flowprime headed rotary scrubber drier in conjunction with a mildly alkaline detergent. Please refer Products Included In This System to Flowcrete's Cleaning & Maintenance Guide for further information. Layer 1 Flowprime *If Required Layer 2 Flowcoat CR Warranty Layer 3 Flowcoat CR Flowcrete products are guaranteed against defective materials and manufacture and are Coving sold subject to our standard Warranty, Terms and Conditions of Sale', copies of which Coving can form an integral part of the can be obtained on request.

6 Warranty does flooring system. It creates a sealed finish not cover suitability, fit for purpose or any between the floor and wall joint. Please consequential or related damages. Please refer to Flowtex F1 Coving Mortar for further review warranty in detail before installing the information. products. Substrate Requirements Concrete or screed substrate should be a minimum of 25 N/mm , free from laitance, dust and other contamination. Substrate should be dry to 75% RH as per ASTM F2170. (AS1884:2012). Flowcrete Australia Pty Ltd Unit 2 41 Deakin Street Brendale QLD 4500 Australia Tel: +61 7 3205 7115 Fax: +61 7 3205 3116.

7 Unit 1 12 Blackmore Road Smeaton Grange NSW 2567 Australia Tel: +61 2 4648 0397 Fax: +61 2 4648 0719. Email: Method Statement System Flowcoat CR Application Equipment Specification Smooth Gloss Finish The use of correct application equipment is critical as incorrect application tools can This specification assumes a concrete result in poor finishing and incorrect material compressive strength greater than consumption. Always test the application 25 N/mm , application and curing equipment prior to commencing work. temperatures of 10 35 C, the presence of an effective damp proof membrane below The following equipment is recommended for substrate and concrete moisture content less this application.

8 Than 75% RH. If moisture content is above 75%. RH, please contact Flowcrete Australia. This specification must be read in conjunction with relevant product technical data sheets and the application of all materials is to be strictly in accordance with manufacturer's instructions. 10-12mm Nap Roller Spike Shoes Manufacturer Flowcrete Australia Pty Ltd Cover - Lambswool *Rolana or Equivalent Address Unit 2, 41 Deakin Street Suburb Brendale State QLD. Postcode 4500. Telephone +61 7 3205 7115. Email Slow Speed Drill with Squeegee Helical Mixer Head Outline for Installation Mechanically Prepare Substrate Apply Flowprime *If Required for @.

9 Porous Surfaces Only Apply Flowcoat CR @ . Apply Flowcoat CR @ . Storage 12 months in an unopened packaging stored at a temperatures of 5-40 C. Protect from frost, weather, moisture and contaminant ingress. Flowcrete Australia Pty Ltd Unit 2 41 Deakin Street Brendale QLD 4500 Australia Tel: +61 7 3205 7115 Fax: +61 7 3205 3116. Unit 1 12 Blackmore Road Smeaton Grange NSW 2567 Australia Tel: +61 2 4648 0397 Fax: +61 2 4648 0719. Email: Safety Precautions Application of Flowprime. Wear appropriate Personal Protective The substrate must be surface dry before the Equipment (PPE) including masks, gloves, application of Flowprime.

10 Eye protection and protective clothing during mixing and application. Ensure the 1. Mixing Flowprime working area is well ventilated and follow Pack components are pre-weighed for the appropriate Health and Safety guidelines optimum performance. Decant required applicable to the location where the amount of material by weight using digital application is undertaken. scales. Stir Base A to re-disperse any settlement. Add Material Set-Up Hardener B to the Base A container, and drain Before commencing work ensure that your thoroughly. Mix with a slow speed drill and material is set-up by separating all components helical spinner head for 1 minute, taking care ( Base A, Hardener B, Filler C etc.)