Caséta Wireless Load Controls SPEC (369987)

1 Specification SubmittalpageJob Name:Job Number:Model Numbers:Cas taR WirelessLoad Controls369987c 1 taR Wireless Load ControlsThe Cas taR Wireless family of Dimmers and Switches can be controlled directly and remotely when paired with PicoR Remote Controls providing a system that delivers convenience and ease of taR Wireless Dimmers and Switches use LutronR patented Clear ConnectR RF Technology which enables Wireless communication with PicoR Remote Controls and the LutronR Smart bridge and Smart bridge Works with PicoR Remote Control Works with the LutronR App (via a Smart bridge or Smart bridge PRO)1 LutronR patented Clear ConnectR RF Technology works through walls and floors Includes Front Accessible Service Switch (FASST) for safe lamp replacement Works with LutronR Radio Powr SavrT Occupancy and Vacancy Sensors in standalone applications (sensors do not work with Smart bridge or Smart bridge PRO)

2 Cas taR Wireless In-Wall SwitchesCas taR Wireless In-Wall DimmersCas taR Wireless Plug-In Lamp DimmerCas taR Wireless ELV+ Dimmer1 The Lutron App is required for setup and usage with the Smart bridge and Smart bridge PRO. The LutronR App is compatible with iOSR devices version or later and AndroidT devices or later. iOS is a registered trademark of Cisco in the and other countries and is used under license. Android is a trademark of Google : Certain models or load types will require a neutral connection (see Load Types and Capacity sections). Specification SubmittalpageJob Name:Job Number:Model Numbers:Cas taR WirelessLoad Controls369987c 2 Approvals cULus Listed NOM Certified FCC Approved. Complies with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules Industry Canada Certified IFTEL Certified NEMA 410 (-5 ANS, -6 ANS, -5WS, -10 NXD, -5NE)PowerOperating voltage: 120 V~ 50/60 Hz: -3 PCL, -6 WCL, -10 NXD, -6 ANS, -5 ANS, -5NE 120 / 277 V~ 50 / 60 Hz: -5WS-DVKey Design Features Tested to withstand electrostatic discharge without damage or memory loss, in accordance with IEC 61000-4-2.

3 Tested to withstand surge voltages without damage or loss of operation, in accordance with IEEE Recommended Practice on Surge Voltages in Low-Voltage AC Power Circuits. Load Controls always operate locally and do not require system control. Power failure memory: should power be interrupted, the control will return to its previously set level prior to the interruption when power is restored. PD-5WS-DV, PD-5 ANS, PD-6 ANS, and PD-10 NXD use conventional 3-way wiring. Uses LutronR ClaroR Wallplates or designer-style wallplates from other manufacturers. Wallplates are sold separately. LutronR ClaroR Wallplates snap on with no visible means of attachment. Requires a 1-gang wallbox. 31 2 in (89 mm) depth recommended, 21 4 in (57 mm) depth minimum. Green status LED(s) to indicate load Communications and Capacity Cas taR Wireless In-Wall Switches and Dimmers communicate with PicoR remote Controls and the LutronR Smart bridge /Smart bridge PRO through Radio Frequency (RF).

4 The Cas taR Wireless In-Wall Switches and Dimmers communicate with LutronR Radio Powr SavrT Occupancy and Vacancy Sensors in a standalone application. Sensors do not work with Smart bridge or Smart bridge PRO. The Cas taR Wireless In-Wall Switches and Dimmers must be located within 60 ft (18 m) line-of-sight or 30 ft (9 m) through walls, of PicoR remote Controls and LutronR Smart bridge limits PicoR Remote Controls and Radio Powr SavrT Occupancy Sensors: up to 10 devices (total) may be paired to each Cas taR Wireless In-Wall Switch/Dimmer (with no Smart bridge installed). Smart bridge or Smart bridge PRO system: up to 50 total Wireless devices (Cas taR Wireless Dimmers/Switches, PicoR Remote Controls , and Shades) are supported per system. Smart bridge or Smart bridge PRO counts as one Ambient operating temperature: 32 F to 104 F (0 C to 40 C), 0% to 90% humidity, non-condensing. Indoor use only.

5 PD-5WS-DV, PD-5 ANS, PD-6 ANS, and PD-10 NXD can be used with mechanical switch in 3-way applications. Specification SubmittalpageJob Name:Job Number:Model Numbers:Cas taR WirelessLoad Controls369987c 3 Dimmer PD-10 NXDPlug-In Dimmer PD-3 PCLIn-Wall Dimmer PD-6 WCLELV+ Dimmer PD-5NE2-wire Switch PD-5WS-DVNeutral Switch PD-5 ANS, PD-6 ANSS imple two-wire installation (no neutral wire required) 1 Capable of dimming loads Favorite button (user defined one touch light level) Works with Hi-lumeR 1% 2-Wire LED Drivers (Forward-phase only) Works with Power Interfaces (PHPM and GRX-TVI) Works with Power Interfaces (PHPM-SW) No wiring required 1 In some low-wattage applications the PD-10 NXD will require a neutral wire Specification SubmittalpageJob Name:Job Number:Model Numbers:Cas taR WirelessLoad Controls369987c 4 Type and Capacity - SwitchesModel NumberDescriptionVoltageLoad TypeMinimum LoadMaximum Load 3 Not GangedEnd of GangMiddle of GangPD-5WS-DV1 Two -w i re switch120 V~Incandescent / Halogen25 W600 W450 W350 W277 V~Incandescent / Halogen25 W1350 W110 0 W800 W120 V~MLV25 W600 VA /475 W450 VA / 350 W 350 VA / 275 W277 V~MLV25 W1350 VA /1075 W 1100 VA / 875 W 800 VA / 625 W120 V~General Purpose A3 A3 A3 A120 / 277 V~LEDUse LUT-MLC25 A4 A3 A120 / 277 V~FluorescentUse LUT-MLC25 A4 A3 A120 V~ELVUse LUT-MLC2600 W450 W350 W277 V~ELVUse LUT-MLC21350 W110 0 W800 WPD-5 ANSN eutral-wire switch (neutral connection required)120 V~Incandescent / Halogen10 W600 W600 W600 WMLV10 W600 VA600 VA600 VAFan0.

6 1 A3 A3 A3 ALED1 bulb5 A5 A5 AFluorescent1 ballast5 A5 A5 AELV10 W600 W600 W600 WPHPM-SW1 interface2 interfaces2 interfaces2 interfacesPD-6 ANSN eutral-wire switch (neutral connection required)120 V~Incandescent / Halogen10 W720 W720 W600 WMLV10 W720 VA720 VA600 VAFan0 .1 ALED1 bulb6 A6 A5 AFluorescent1 ballast6 A6 A5 AELV10 W720 W720 W600 WPHPM-SW1 interface3 interfaces3 interfaces3 interfaces1 No neutral wire To ensure proper operation of the switch with LED, fluorescent, and ELV loads, a LUT-MLC (included) may be required, especially at lower wattages. If the status LED on the switch is flashing or solid red in color, a LUT-MLC must be installed. To guarantee best performance, installing a LUT-MLC with these load types regardless of wattage is recommended. Rarely, some load types may still flicker or glow in the off state even with the LUT-MLC installed, in which case a different load may be required or more than one LUT-MLC is See Ganging and Derating section.

7 Specification SubmittalpageJob Name:Job Number:Model Numbers:Cas taR WirelessLoad Controls369987c 5 Cannot be Need to change load type to MLV. See See bulb list at F or PD-10 NXD, a neutral connection is required for MLV loads, LED drivers, dimmable ballasts, and power modules (PHPM-PA, PHPM-3F, and GRX-TVI).5 Compatible dimmable ballasts include Tu-WireR, Mark X, and These loads are best operated using a forward-phase control. Consult to ensure the appropriate phase for bulb models SSL7 compliant when in forward-phase. 8 Canadian packaged Available in WH Kit model number. Kit includes (1) PD-3 PCL-WH, and (1) PJ2-3 BRL-WH-L01R (3-button with raise/lower Pico Wireless control in White).11 Kit model number. Kit includes (1) L-BDG2-WH (Cas ta Wireless Smart bridge with HomeKit technology), (1) PD-3 PCL-WH, (1) PJ2-3 BRL-WH-L01R (3-button with raise/lower Pico Wireless control in White) and (1) L-PED1-WH (Single tabletop pedestal in White).

8 12 Kit model number. Kit includes (1) PD-6 WCL-WH, (1) PJ2-3 BRL-WH-L01R (3-button with raise/lower Pico Wireless control in White), and (1) CW-1-WH (single-gang faceplate in White).13 Kit model number. Kit includes (1) L-BDG2-WH (Cas ta Wireless Smart bridge with HomeKit technology), (1) PD-6 WCL-WH, (1) PJ2-3 BRL-WH-L01R (3-button with raise/lower Pico Wireless control in White), and (1) CW-1-WH (single-gang faceplate in White).14 Kit model number. Kit includes (1) L-BDG2-WH (Cas ta Wireless Smart bridge with HomeKit technology), (2) PD-6 WCL-WH, (2) PJ2-3 BRL-WH-L01R (3-button with raise/lower Pico Wireless control in White), (2) L-PED1-WH (Single tabletop pedestal in White) and (2) CW-1-WH (single-gang faceplate in White).15 PRO Kit model number. Kit includes (1) L-BDGPRO2-WH (Cas ta Wireless Smart bridge PRO with HomeKit technology), (1) PD-6 WCL-WH, (1) PJ2-3 BRL-WH-L01R (3-button with raise/lower Pico Wireless control in White) and (1) CW-1-WH (single-gang faceplate in White).

9 Load Type and Capacity - DimmersModel NumberDescriptionVoltageLoad TypeMinimum LoadMaximum LoadNot GangedEnd of GangMiddle of GangPD-10 NXDPD-10 NXD-XX-C 8 Wireless In-Wall Dimmer PRO (neutral connection required for certain load types)4120 V~Incandescent / Halogen10 W with neutral (25 W without neutral)1000 W800 W600 WMLV Halogen10 W1000 VA800 VA600 VAMLV LEDSee Application Note #559 CFL/LED (120 V~ Rated)31 bulb3250 W250 W250 WHi-lumeR 1% 2-Wire LED drivers1 driver13 drivers13 drivers13 driversDimmable Ballasts51 ballast1000 VA 800 VA 600 VAPHPM-PA/3F and GRX-TVI 41 interface3 interfaces3 interfaces3 interfacesPD-3 PCL1, 9PD-3 PCL-WH-C 8P-PKG1P-WH 9, 10P-BDG-PKG2P 9, 11 Wireless Plug-In Lamp Dimmer120 V~Incandescent / Halogen10 W300 WN/AN/ACFL/LED (120 V~ Rated)31 bulb3100 WN/AN/APD-5 NEPD-5NE-XX-C 8 Phase Selectable Dimmer (neutral connection required)120 V~Incandescent / Halogen10 W500 W400 W300 WCFL/LED (120 V~ Rated)3, 6, 71 bulb3250 W250 W250 WMLV Halogen 2, 6, 710 W400 VA400 VA400 VAELV Halogen10 W500 W400 W300 WHi-lumeR 1% 2-Wire LED drivers 6, 71 driver20 drivers20 drivers20 driversDimmable Ballasts 5, 6, 71 ballast400 VA400 VA400 VAPHPM-PA/3F and GRX-TVI 6, 71 interface3 interfaces3 interfaces3 interfacesELV LEDSee Application Note #559 MLV LED 6, 7 See Application Note #559PD-6 WCLPD-6 WCL-XX-C 8P-PKG1W-WH 9, 12P-BDG-PKG2W 9, 13P-BDG-PKG2W 9, 14P-BDGPRO-PKG1W 9, 15 Wireless In-Wall Dimmer120 V~Incandescent / Halogen25 W600 W500 W400 WCFL/LED (120 V~ Rated)31 bulb3150 W150 W150 W Specification SubmittalpageJob Name:Job Number:Model Numbers:Cas taR WirelessLoad Controls369987c 6 and DeratingWhen ganging with other Switches/Dimmers in the same wallbox, derating is required.

10 See Load Type and Capacity Switch/Dimmer has inside fins removedMiddle of ganged Switches/Dimmers have all fins removedDo not remove outside fins on ends of ganged Switches/DimmersDo not remove outside fins on ends of ganged Switches/DimmersEach Switch/Dimmer has inside fins removedMiddle of ganged Switches/Dimmers have all fins removed Specification SubmittalpageJob Name:Job Number:Model Numbers:Cas taR WirelessLoad Controls369987c 7 Front Accessible Service SwitchImportant Notice: To service load, remove power by pulling out the FASST as far as possible. To restore power after servicing load, push the FASSTM back in FASSTM FASSTM FASSTM FASSTM FASSTM Status LEDI ndicates load status; glows softly as night light when load is offELV+ Dimmer and In-Wall DimmersFASSTM FASSTM FASSTM FASSTM FASSTM FASSTM FASSTF ront Accessible Service SwitchFASSTF ront Accessible Service SwitchOnStatus LEDsIndicates load status; glows softly as night light when load is offOffBrighterDarkerIn-Wall SwitchesFavorite (User defines light level.)