Charged Device Model (CDM) Qualification Issues

1 Charged Device Model (CDM) Qualification Issues Industry Council on ESD Target levels CDM Presentation 2 Purpose /Abstract IC design for performance constraints make it increasingly difficult to meet the current CDM levels as the technologies continue to shrink and the circuit speed demands continue to increase This work shows that devices with CDM levels below the general target of 500 V can safely be handled with CDM control methods available in the industry today Based on these observations and constraints it will be shown through this work that 250V is a safe and practical target cdm level Industry Council on ESD Target levels CDM Presentation 3 Outline Relevance of CDM CDM Technology & Design Issues

2 CDM Qualification Methods ESD Control Methods Addressing CDM Analysis of Field Return Data Summary Conclusion Roadmap Industry Council on ESD Target levels CDM Presentation 4 Relevance of CDM CDM is a unique and important test method for IC component ESD testing There are proven damage signatures for field returns due to fast ESD discharges with high peak current that cannot be reproduced by HBM (or MM) CDM testing can effectively replicate these failure signatures Typical discharge scenarios have been simulated in IC testing and observed in manufacturing which cause CDM failure signatures CDM is a necessary and important Qualification test Industry Council on ESD Target levels CDM Presentation 5 CDM protection design is primarily driven by the peak current from the IC package discharge at the required (targeted) CDM voltage level.

3 Increasing package size (and capacitance) lead to increasing peak CDM current for a given CDM stress voltage. Additionally, CDM protection design is increasingly limited by reduction in breakdown voltage of gate dielectrics and junctions. CDM Technology & Design Issues Industry Council on ESD Target levels CDM Presentation 6 IC Circuit Speed Demand IC Die and Package Size Technology Scaling IC Breakdown Voltage Reduced ESD Design Window Practical CDM levels CDM Technology & Design Issues Parasitics from ESD devices IC design requirements create severe limitations for CDM protection CDM Discharge Current Customer/ Design Requirements Impact on ESD Issues Solution Difficult to meet currently accepted CDM levels Industry Council on ESD Target levels CDM Presentation 7 Impact of Package on CDM Discharge Current @500V I t 1A I t 12-15A 8-Pin DIP 2400-Pin LGA Wide variations (>12X)

4 In the peak discharge current from the smallest to the largest IC packages Industry Council on ESD Target levels CDM Presentation 8 500 1000 1500 2000 2500 3000 2002 0 Pin Count 2004 2006 2008 2010 Calendar Year Trends in IC Package Pin Counts: Microprocessors 2012 2014 2016 4000 5000 Higher pin count devices at every new tech node are market driven towards HSS pins on microprocessors Industry Council on ESD Target levels CDM Presentation 9 Calendar Year 370423603604 TJB1B2B3H1H2H3G1G2G3 RLSN (479)Number of contactsLaunch yearNext socket targetTrends in IC Package Pin Counts: Server Sockets Industry Council on ESD Target levels CDM Presentation 10 CDM peak Current @500V Vs. Pin Count (Package Area) Jahanzeb et al, ESD Symp.

5 2007 0 2 4 6 8 10 12 14 0 1000 2000 3000 Package Area (mm 2 ) CDM Peak Current (A) 100 3000 1000 500 Pin Count Variations in Peak Current Industry Council on ESD Target levels CDM Presentation 11 Capacitive loading of ESD protection for high speed serial (HSS) link design is limited to ~ 100 fF. The limitation to 100 fF only allows a maximum peak current of 4 A in this example. For BGA with more than 300 pins this limits the cdm level to 250 V at best. CDM Analysis - Example for High Speed Serial Link High Speed Serial Links - 45nm Bulk CMOS 0 10 20 30 40 50 60 70 80 0 100 200 300 400 500 600 ESD Capacitive Loading Budget [fF] Data Rate [Gigabits/sec] 0 1 2 3 4 5 6 Peak CDM Current [A] Max.

6 HSS data rate vs. capacitive loading CDM peak current - double diodes + RC- Clamp (Substrate Charged neg) CDM peak current - DTSCR + RC-Clamp (Substrate Charged neg) Industry Council on ESD Target levels CDM Presentation 12 Overview of CDM Design Capability for Advanced Nodes with 10-20 GB/s Speed Performance Tech. Node Design Type Max Achievable CDM Peak Current Corresponding cdm level 65nm High Speed Serial Link 5-6 Amps 300-400V 45nm High Speed Serial Link 4-5 Amps 250-300V 45nm Radio Frequency (RF) 2-3 Amps 200-250V 200-250V becomes the new practical level that is achievable Industry Council on ESD Target levels CDM Presentation 13 Relevance of ESD Control for Safe Manufacturing For CDM, as with HBM, ESD control in the production areas is an essential part of a safe manufacturing process Effective ESD control measures covering CDM events include the grounding of metallic machine parts.

7 Control of metal-to-metal contact with the Device leads AND control of insulators Control of insulators requires assessment of the various handling steps Industry Council on ESD Target levels CDM Presentation 14 Basic ESD Control Program addressing CDM Ionizer if there are process relevant insulators that are considered a threat Remove all non-process relevant insulators E-Field measurements by Field Meter or Field Mill Below Threat Level Dissipative Worksurface Threat level per ANSI/ESD and IEC 61340-5-1 Industry Council on ESD Target levels CDM Presentation 15 Relationship between General ESD Control and CDM Specific Control Industry Council on ESD Target levels CDM Presentation 16 Analysis of FAR Data FAR data was collected from various Council members for over 11 billion shipped IC's.

8 Field returns include returns from handling and testing by IC suppliers, manufacturing of the PCBs and end-customer returns. 949 designs have been included covering automotive, consumer, memory and discrete products. The presented data were collected in the time frame from 2003 to 2007. Industry Council on ESD Target levels CDM Presentation 17 FAR Data versus CDM voltage Important Observations: EOS/ESD failure rates do not show a clear trend with respect to dependence of the CDM voltage A few designs with high return rates (outliers) dominate the statistics Further Limitations: devices not always tested to failure voltage Discrepancy between JEDEC and ESDA testers Rel. Humidity during testing not controlled/recorded <= 200>200 =< 300>300 =<400>400 =<500>500 <=750>750 <=1000>1000 =<1250>1250 =<1500>1500 =<1750>1750 =<2000>20000,00,20,40,60,81,01,21,41,61,82,0128 0 M1260 M2210 M86 M600 M460 M2300 M1000 M1200 M390 M730 Mbased on billion devicesupper limit of EOS/ESD failure rateCDM robustness [V] Industry Council on ESD Target levels CDM Presentation 18 FAR Data versus CDM voltage w/o Outliers Important Observations.

9 Excludes 15 designs classified as FAR outliers (defined by > 100 field returns per type) Remaining designs (934 out of 949) show a FAR rate < 1 dpm No increase in the average return rate of parts with lower CDM levels <= 200>200 =< 300>300 =<400>400 =<500>500 <=750>750 <=1000>1000 =<1250>1250 =<1500>1500 =<1750>1750 =<2000>20000,00,10,20,30,40,50,60,70,80,91,01,1 1200 M870 M2200 M220 M1040 M290 M2260 M220 M360 M570 M1 dpm linebased on billion devicesupper limit of EOS/ESD failure rateCDM robustness [V] Industry Council on ESD Target levels CDM Presentation 19 FAR Data versus CDM peak current Contains one outlier in TQFP 100 with 409 fails out of 36 Mio (VCDM = 1000V) Limitations: Some peak currents were measured with a 1 GHz scope, others with 4 GHz scope (up to a factor of two difference in peak value) BUT.

10 EOS/ESD failures occur at all CDM peak currents levels (even at very high values) 0<=22-<=33-<=44-<=55-<=66-<=77-<=88-<=99-<=1010-<=1111-<=1212-<=1414-<=16>160,00,51,01,52,02,531 Mio sold100 Mio sold150 Mio sold200 Mio sold280 Mio sold480 Mio sold260 Mio sold370 Mio sold540 Mio sold1170 Mio sold990 Mio sold470 Mio sold910 Mio sold280 Mio soldbased on 6,2 Billion devicesEOS/ESD failure [dpm]CDM peak current [A] Industry Council on ESD Target levels CDM Presentation 20 Analysis of FAR of a CDM Weak Device Low CDM Effect on FAR 140-Pin BGA shows 30 failures out of 67M units shipped CDM performance = <125V FA shows clear damage on IO gate due to marginal design Identical damage was detected on units stressed at 125V Implementing advanced CDM controls resulted in 0 FAR for 105M shipped Control measures can be effective.