Example: bachelor of science
CHEMICAL RESISTANCE GUIDE
and stronger than the copolymer grade. Piping is normally PP-H. a few Chemline valves are also PP-H. The working temperature range of PP-H back pressure valves for example is 10 to 70°C (50 to 158°F). • Copolymer (PP-R) made from Type II resin produced from Random 94% propylene with 6% ethylene. PP-R is a bit softer but has better
Tags:
Information
Domain:
Source:
Link to this page:
Documents from same domain
BORE CHART (INSIDE DIAMETER OF PIPE)
everythinginsidethefence.comLight, Black = Weight per Foot Wall Thickness displayed are in inches and Weights displayed are in pounds/foot. IF THE WEIGHT IS NOT DISPLAYED USE THE FOLLOWING FORMULA TO CALCULATE THE WEIGHT OD – Wall x Wall x 10.68 = LBS / FOOT PIPE SIZE DN O.D. in inches 5 10 20 30 40 Std 60 80 XH 100 120 140 160 XXH 1 / 8 0.405 1 / 4 0.540 3 / 8 10 0.675 ...
Related documents
HYOSUNG CHEMICAL POLYPROPYLENE
www.hyosungchemical.comRandom CPP Transparent, USP Class VI, EP §3.1.6, US FDA DMF 21499, CFDA R530C 7 7,500 10 ... IMPACT COPOLYMER / HOMOPOLYMER Property ASTM Method Unit Melt Flow Index D1238 ... 95 110 General injection Processibility, Stiffness, UL 94HB J800 23 370 16,500 3 / …
Polypropylene Random Copolymer for Injection Moulding ...
www.bhavikenterprises.comPolypropylene RJ470MO Polypropylene Random Copolymer for Injection Moulding IM 1246 30.10.2004 Ed. 3 Borealis A/S Parallelvej 16 DK-2800 Kongens Lyngby (Denmark) Telephone: +45 45 96 60 00 Fax : +45 45 96 61 23 www.borealisgroup.com Description RJ470MO is a highly transparent polypropylene random copolymer with very high fluidity intended for
Polypropylene (PP)
www.opalindia.inPolypropylene – Random Copolymer High Speed Molding, Rigid Packaging, Thin Wall Molding, Deli g MR12C 12 Clarified, Antistatic High Clarity Rigid Containers, Media Packaging, Housewares, Injection Stretch Blow Moulding MR20K 20 Clarified, Antistatic Housewares, Rigid Packaging, Consumer Products MR35K 35 Clarified, Antistatic,
永嘉烯品級物性表YUNGSOX PP resin properties data sheet (2)
www.fpc.com.twInjection Grade High Impact Copolymer 無規共聚物 Random Copolymer 4084 4204 4304 5060 5060T 5090T 5200XT 5090R 5350T 熔融指數 Melt Index g/10min ISO1133 10 19 30 7 7.5 15 18 17 35 熱變形溫度 Heat Deflection Temperature ℃ ASTM D648 100 100 100 90 95 95 95 95 95 軟化點溫度 Vicat Softening Temperature
www.bis.gov
bis.gov.inPolypropylene-random Copolymer Pipes For Hot And Cold Water Supplies - 90 IS 2052 Compounded Feeds For Cattle 91 IS 3601 Steel Tubes For Mechanical And General Engineering Purposes 92 IS 8034 Submersible Pumpsets - Specification
Products and Properties - Braskem Usa
www.braskem.comPP • Polypropylene Injection Molding Typical Properties Melt Flow (230 C, 2.16 kg) Flexural Modulus (0.05in/min, 1% secant) Notched Izod Impact Strength @ 23 C Tensile Strength @ yield (2 in/min) ASTM Method D1238 D790A D256A D638 Units g/10' psi MPA ft-lb/in J/m psi MPA HOMO F006EC2 0.5 200,000 1,379 1.3 69 4,900 34 Enhanced long term heat ...
POLYMER STRUCTURE AND CHARACTERIZATION
www.cof.orst.educopolymer polymerized from monomers of adipic acid and hexamethyl diamine. Although it is a copolymer, the structure on the right side Fig. 1.1 can be viewed as the single repeat unit for Nylon 6/6. The \6/6" in the polymer name denotes the number of …