CLASSIC SERIES - stenner.com

1 TO BE INSTALLED AND MAINTAINED BY PROPERLY TRAINEDPROFESSIONAL INSTALLER ONLY. READ manual & LABELSFOR ALL SAFETY INFORMATION & METERING pumps SINCE 1957 CLASSIC SERIESPERISTALTIC METERING PUMPSINSTALLATION AND MAINTENANCE manual CLASSIC OF CONTENTSW arranty and Service Policy ..3 Safety , 14-16, 19-23, 26, 27, 35 Flow Rate Outputs ..6-11 Materials of Construction ..12 Accessories ..23-26 Tube Replacement ..27-34 Cleaning the Point of Exploded View and Rate Control Exploded View and Parts ..42-43 Pump Head Exploded View and Parts ..44-46 Pump Tubes ..47 Check Your Records ..49 IMCL 021822US and Canada , International CLASSIC Series3 WARRANTY AND CUSTOMER SERVICELIMITED WARRANTYS tenner Pump Company will for a period of one (1) year from the date of purchase (proofof purchase required) repair or replace, at our option, all defective parts.

2 Stenner is notresponsible for any removal or installation costs. Pump tube assemblies and rubbercomponents are considered perishable and are not covered in this warranty. Pump tubewill be replaced each time a pump is in for service, unless otherwise specified. The cost ofthe pump tube replacement will be the responsibility of the customer. Stenner will incurshipping costs for warranty products shipped from our factory in Jacksonville, Florida. Anytampering with major components, chemical damage, faulty wiring, weather conditions,water damage, power surges, or products not used with reasonable care and maintained inaccordance with the instructions will void the warranty. Stenner limits its liability solely tothe cost of the original product. We make no other warranty expressed or offers a 30-day return policy on factory direct purchases.

3 Except as otherwiseprovided, no merchandise will be accepted for return after 30 days from purchase. Toreturn merchandise at any time, call Stenner at for a Return MerchandiseAuthorization (RMA) number. A 15% re-stocking fee will be applied. Include a copy of yourinvoice or packing slip with your OR LOST SHIPMENTSAll truck shipments: Check your order immediately upon arrival. All damage must be notedon the delivery receipt. Call Stenner Customer Service at for all shortagesand damages within seven (7) days of & REPAIRSB efore returning a pump for warranty or repair, remove chemical from pump tube byrunning water through the tube, and then run the pump dry. Following expiration of thewarranty period, Stenner Pump Company will clean and overhaul any Stenner meteringpump for a minimum labor charge plus necessary replacement parts and shipping.

4 Allmetering pumps received for overhaul will be restored to their original condition. Thecustomer will be charged for missing parts unless specific instructions are given. To returnmerchandise for repair, call Stenner at or for a ReturnMerchandise Authorization (RMA) information contained in this manual is not intended for specific application Pump Company reserves the right to make changes to prices, products, andspecifications at any time without prior is a registered trademark of the Stenner Pump is a registered trademark of Exxon Mobil is a registered trademark of Saint-Gobain Performance is a registered trademark of Lubrizol Advanced Materials, is a trademark of Houghton INFORMATIONIMPORTANT SAFETY INSTRUCTIONSWhen installing and using this electrical equipment, basic safety precautionsshould always be followed, including the following.

5 READ AND FOLLOW ALL INSTRUCTIONSW arns about hazards that CAN cause death, serious personalinjury, or property damage if SHOCK HAZARDELECTRIC SHOCK HAZARD Pump supplied with grounding power cord and attached plug. To reduce risk ofelectrical shock, connect only to a properly grounded, grounding type only on a circuit protected by a Ground-Fault Circuit-Interrupter (GFCI).DANGER DE CHOC LECTRIQUE La pompe est dot e d un cordon d alimentation avec mise la terre muni d'unefiche. Pour r duire le risque de choc lectrique, branchez uniquement sur une prisecorrectement mise la terre. Installez uniquement sur un circuit prot g par undisjoncteur diff NOTalter the power cord or plug NOTuse receptacle NOTuse pump with a damaged or altered power cord or plug. Contact thefactory or an authorized service facility for VOLTAGE DISCONNECT power cord before removing motor cover for service.

6 Electrical serviceby trained personnel HAZARD This equipment IS NOTexplosion proof. DO NOTinstall or operate in an explosive OF CHEMICAL EXPOSURE Potential for chemical burns, fire, explosion, personal injury, or property damage. Toreduce risk of exposure, the use of proper personal protective equipment is OF FIRE HAZARD DO NOTinstall or operate on any flammable OF CHEMICAL OVERDOSE To reduce risk, follow proper installation methods and recommendations. Check yourlocal codes for additional reduce the risk of injury, do not permit children to use thisproduct. This appliance is not to be used by persons with reduced physical, sensoryor mental capabilities, or lack of experience or knowledge, unless they have beengiven supervision or and Canada , International CLASSIC Series5 SAFETY INFORMATION continuedWarns about hazards that WILL or CAN cause minor personal injury or property damage if Chemical feed pump installation must always adhere to your local plumbing codes and requirements.

7 Be sure installation does not constitute a cross connection. Checklocal plumbing codes for : Indicates special instructions or general mandatory metering pump is portable and designed to be removable from the plumbingsystem without damage to the installing or servicing the pump, read the pump manual for all safetyinformation and complete instructions. The pump is designed for installation andservice by properly trained of product must adhere to all regulatory and compliance codesapplicable to the metering pump and its components have been tested for use with the followingchemicals: Sodium Hypochlorite (10-15%), Muriatic Acid (20-22 Baume, ), and Soda pompe de dosage et ses composants ont t test s pour leur compatibilit avec les produits chimiques suivants : hypochlorite de sodium (10 15 %), acidechlorhydrique (20 22 % Baume, 31,5 % HCl), et carbonate de metering pump is certified by WQA for use with Water and Sodium Hypochlorite15%, when using Santoprene tube material.

8 This is the safety alert symbol. When displayed in this manual or on theequipment, look for one of the following signal words alerting you to thepotential for personal injury or property SUITABLE FOR USE OUTDOORS when installed with a Stenner Rain Roof PartNo. installation should adhere to all national and local codes. Consult alicensed professional for assistance with proper electrical power from pool/spa recirculation pump must also remove power from use of an auxiliary safety device (not supplied), such as a flow switch or sensor,is recommended to prevent feed pump operation in the event of a recirculationpump failure or if flow is not of chemical injection should be beyond all pumps , filters, and for indoor and outdoor e une utilisation aussi bien l int rieur qu l ext THESE INSTRUCTIONSM odelItem Number Maximum Pump Feed Rate Control SettingPrefixpsi / bar TubeL1234567891045 MHP245 MJH1100 / / / / / / / / RATE OUTPUTS CLASSIC 45 NOTICE:The information within this chart is solely intended for use as a guide.

9 The output data is an approximation based onpumping water under a controlled testing environment. Many variables can affect the output of the pump. Stenner PumpCompany recommends that all metering pumps undergo field calibration by means of analytical testing to confirm their Head Adjustable Gallons per Number Maximum Pump Feed Rate Control SettingPrefixpsi / bar TubeL1234567891045 MHP245 MJH1100 / / / / / / / / Head Adjustable Liters per Head Fixed Gallons & Liters per DayModelItem Number Maximum PumpGPD @ 60 HzLPD @ 50 HzPrefixpsi / bar Tube45 MPHP245 MFH1100 / / / / / / / / Outputs @ 60 HzApproximate Outputs @ 50 HzApproximate Outputs @ 60 & 50 HzUS and Canada.

10 International CLASSIC Series7 ModelItem Number Maximum Pump Feed Rate Control SettingPrefixpsi / bar TubeL1234567891085 MHP585 MJH1100 / / / / / / / / RATE OUTPUTS CLASSIC 85 NOTICE:The information within this chart is solely intended for use as a guide. The output data is an approximation based onpumping water under a controlled testing environment. Many variables can affect the output of the pump. Stenner PumpCompany recommends that all metering pumps undergo field calibration by means of analytical testing to confirm their Head Adjustable Gallons per Head Adjustable Liters per DaySingle Head Fixed Gallons & Liters per Day1 ModelItem Number Maximum PumpGPD @ 60 HzLPD @ 50 HzPrefixpsi / bar Tube85 MPHP585 MFH1100 / / / / / / / / Outputs @ 60 HzModelItem Number Maximum Pump Feed Rate Control SettingPrefixpsi / bar TubeL1234567891085 MHP585 MJH1100 / / / / / / / / Outputs @ 50 HzApproximate Outputs @ 60 & 50 HzClassic.